Manual Operation; Wall Thermostat Operation; Installation Of Remote Receiver; Wiring Diagram - Empire Comfort Systems CIVF-25-2 Installation Instructions And Owner's Manual

Wiring of ON/OFF/REMOTE Switch with 750 Millivolt Wall
Thermostat Accessory and Another Accessory
Connect the green and red, stripped and bare, wires on the ON/OFF/
REMOTE switch wire harness to the 750 millivolt wall thermostat AND
to the remote receiver that is a component in the FRBC-1, FREC-1 OR
to the FWS-1, wall switch.
1. Connect (1) wire from the 750 millivolt wall thermostat and (1) wire
from appropriate accessory to the GREEN, stripped and bare wire
from the ON/OFF/REMOTE wire harness.
2. Connect (1) wire from the 750 millivolt wall thermostat and (1) wire
from appropriate accessory to the RED, stripped and bare wire from
the ON/OFF/REMOTE wire harness.
Note: When the appliance is in the MANUAL mode and the batteries
fail in the FRBC-1 or if the electric (120 volt) fails in the FREC-1, and
immediate heat is desired, turn the ON/OFF/REMOTE switch on
wiring chase from the REMOTE position to the ON position.

Manual Operation

1. Turn ON/OFF/REMOTE switch on wiring chase to REMOTE
position.
2. Turn wall thermostat OFF.
3. Turn accessory, FRBC-1, FREC-1 or FWS-1, ON. Appliance is now
in the manual mode. You must turn the appliance ON or OFF with
appropriate accessory.

Wall Thermostat Operation

1. Turn the ON/OFF/REMOTE switch on wiring chase to REMOTE
position.
2. Turn accessory, FRBC-1, FREC-1 or FWS-1, OFF.
3. Turn wall thermostat ON and set appropriate temperature. Wall
thermostat will cycle the appliance ON and OFF.

Installation of Remote Receiver

(Figure 17)
1. Attach, from left to right, the slide-on cover plate onto the remote
receiver. ON will be to the top and OFF will be to the bottom on the
slide-on cover plate.
2. Push the receiver slide button onto the receiver slide switch. Reverse
installation of the slide button if it is off center.
3. Attach velcro loop on the left side of the valve cover support.
4. Attach velcro hook onto remote receiver. The word TOP on the
remote receiver should be to the top when installed onto valve cover
support.
5. Attach velcro hook on remote receiver onto velcro loop on valve
cover support..
Figure 17
Page 12
Wiring Diagram (Figure 18)
.
Figure 18
PLEASE NOTE
It is normal for appliances fabricated of steel to give off some
expansion and/or contraction noised during the start up or cool
down cycle. Similar noises are found with your furnace heat
exchanger or car engine.
Installation of Logs (Figure 19)
1. Remove screen front from inner body by removing (4) 1/2" hex-head
screws.
2. Remove logs from interior of inner body. Remove all protective
packaging from logs and interior of inner body.
3. Align the two rear pins on the base with the two alignment holes on
the underside of the rear log. Place the rear log onto the two rear pins
on the base.
4. Align the two front pins on the base with the two alignment holes on
the underside of the front log. Place the front log onto the two front
pins on the base.
5. Align the two pins on the front log with the two alignment holes on
the underside of the top log. Place the top log onto the two pins on
the front log.
6. Replace and attach screen front onto inner body with (4) 1/2" hex-
head screws from Step 1.
7. Installation of logs is completed.
Refer to Figure 19 for the following warning.
Warning: Failure to position the parts in accordance with this
diagram or failure to use only parts specifically approved with this
appliance may result in property damage or personal injury.
R-3451