Switching The Phase; Graphic Equalizer Adjustments - Alpine DVA-9861Ri Owner's Manual

8
Select the desired channel by pressing
then press MODE.
When L+R is selected :
FRONT 1 FRONT 2
SUBWOOFER FRONT 1
When L/R is selected :
FRONT 1L FRONT 1R
REAR L REAR R CENTER
FRONT 1L
• The speakers display differs, depending on the connected speakers.
9
Adjust the calculated time correction value (0.00 to
20.00ms) by turning the Rotary encoder, then
press MODE.

Switching the Phase

10
Switch the phase (PHASE 0° or 180°) by turning the
Rotary encoder, then press MODE.
11
To adjust other channels, repeat steps 8 to 10.
12
When the setting is complete, press and hold TA for
at least 2 seconds.
The unit returns to the normal mode.
• When the speaker is set to the "OFF" mode, the TCR for that
speaker cannot be set. Refer to "Setting the Speakers" (page 37).
• The adjustment value for FRONT2 (Speakers) which is adjusted in
time correction, is also applied to the front speakers in "Setting Bass
Focus" (page 41).
• The adjustment (AUTO TCR) cannot be automatically set on this
unit.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 44.
or
REAR CENTER
FRONT 2L FRONT 2R
SUBWOOFER
,

Graphic Equalizer Adjustments

The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and centre
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
1
Check that Defeat mode is off (page 25).
2
Press and hold TA for at least 2 seconds.
The audio processor control mode is activated.
3
Select the G-EQ mode by pressing TA repeatedly.
4
Select L+R or L/R by pressing and holding BAND for
at least 2 seconds.
L+R: Sets the same adjustment values for the left and right
channels.
L/R: Different adjustment values can be set for the left and
right channels.
When parametric EQ is adjusted, this setting will be turned
off.
5
Select the desired channel by pressing
then press MODE.
When L+R is selected :
FRONT REAR
When L/R is selected :
FRONT L FRONT R
SUBWOOFER
• The speakers display differs, depending on the connected speakers.
6
Select the frequency by turning the Rotary
encoder, then press MODE.
Adjustable frequency:
FRONT/REAR/CENTER: 20Hz - 20kHz (in 1/3 octave steps)
SUBWOOFER:
7
Adjust the level (LEVEL) (±9dB 1dB step) by turning
the Rotary encoder, then press MODE.
8
To adjust other frequencies, repeat steps 6 and 7.
9
To adjust other channels, repeat steps 5 to 8.
10
When the setting is complete, press and hold TA for
at least 2 seconds.
The unit returns to the normal mode.
• When the speaker is set to the "OFF" mode, the level of the graphic
equalizer for that speaker cannot be adjusted. Refer to "Setting the
Speakers" (page 37).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 44.
CENTER SUBWOOFER
REAR L REAR R CENTER
FRONT L
20Hz - 160Hz (in 1/3 octave
steps)
39
or ,
FRONT
-EN