Auto Standby - Onkyo TX-NR626 Owner's Manual

■
Audio Return Channel
Off
Auto:
The audio signal from your TV tuner can be sent
to HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an
ARC capable TV to send the audio stream to HDMI
OUT MAIN of the AV receiver. To use this function,
you must select the TV/CD input selector and your TV
must be ARC capable. The ARC indicator will light
when the audio signal is detected. Default setting:
" "
- - - -
Note
• This setting is fixed to "- - - -" when the "HDMI CEC (RIHD)"
setting is set to "Off".
• This setting is set to "Auto" automatically when the "HDMI
CEC (RIHD)" setting is set to "On" for the first time.
• If you set "Audio Return Channel" to "Auto", the "Audio
Selector" settings of the TV/CD input selector will be
automatically switched to "ARC" (➔ page
Tip
• After changing the settings of the "HDMI CEC (RIHD)",
"HDMI Through" or "Audio Return Channel", turn off the
power on all connected pieces of equipment and then turn
them on again. Refer to the user's manuals for all
connected pieces of equipment.
■
Lip Sync
Off
On
This function allows the AV receiver to automatically
correct any delay between the video and the audio,
based on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV
supports HDMI Lip Sync.
■
InstaPrevue
These settings apply to "InstaPrevue" of the Home
menu
(➔ page 47)
HDMI video streams.
Sub Window
Multi:
Displays preview thumbnails all at once.
Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.
Position
(with "Sub Window" set to "Multi")
Top, Bottom, Left, Right
(with "Sub Window" set to "Single")
Upper Left, Upper Right, Lower Left, Lower
Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
62).
Note
• Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.

Auto Standby

■
Auto Standby
Off
On
When "Auto Standby" is set to "On", the ASb
indicator lights and the AV receiver will automatically
enter standby mode if there is no operation for 30
minutes with no audio and no video signal input.
"Auto Standby" will appear on the AV receiver's
display and OSD 30 seconds before the Auto
Standby comes on.
and specify the preview display of
En-66
Advanced Operations
Default setting: On (European, Australian and
Asian models), Off (North American and
Taiwanese models)
Note
• Set to " On" , the Auto Standby function may activate itself
during playback with some sources.
• The Auto Standby function does not work when Zone 2 is
on.
■
HDMI Through
Off
On
This setting enables or disables the Auto Standby
during HDMI Through by detecting the audio/video
input signal.
When this setting is set to "On", the AV receiver will
automatically enter standby mode if there is no audio
and no video signal input during HDMI Through for 30
minutes. (The Auto Standby function does not work
when Zone 2 is on.)
When this setting is set to "Off", the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
• Entering standby mode is possible by setting "HDMI CEC
(RIHD)" to "On" and using CEC-compatible component
regardless of the above-mentioned setting.
See "HDMI CEC (RIHD)" in "7. Hardware Setup" for linked
operation (➔ page 64).
• When the HDMI Through is enabled, the power
consumption slightly increases.
Note
• This setting is fixed to "Off" when "Auto Standby" is set to
"Off".
Operating
procedure
(➔ page 52)