Onkyo TX-NR626 Owner's Manual page 25

1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV
receiver is connected.
2 Set the speaker setup microphone at the Main
Listening Position , and connect it to the
SETUP MIC jack.
SETUP MIC jack
Speaker setup microphone
The speaker setting menu appears.
Note
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN. If your TV is
connected to other video outputs, use the AV
receiver's display when changing settings.
3 When you've finished making the settings,
press ENTER.
MultEQ: Auto Setup
Speakers Type (Front)
Powered Zone 2
Surround Back/Front High
Subwoofer
Perform the "2. Speaker Setup" according to your
speaker configuration:
– Speakers Type (Front) (➔ page
– Powered Zone 2 (➔ page 55)
– Surround Back/Front High (➔ page
– Subwoofer (➔ page 56)
If you use a powered subwoofer(s), go to step 4.
If not, go to step 5.
4
Adjust the subwoofer volume level to 75 dB,
and then press ENTER.
Test tones are played through the subwoofer.
Use the volume control on the subwoofer.
Note
• If your subwoofer does not have a volume control,
disregard the displayed level and press ENTER to
proceed to the next step.
• If you set the subwoofer's volume control to its
maximum and the level displayed is lower than 75 dB,
leave the subwoofer's volume control at its maximum
and press ENTER to proceed to the next step.
5
Use / to select "Audyssey Quick Start" or
"Audyssey MultEQ Full Calibration", and then
press ENTER.
6 Press ENTER.
Audyssey MultEQ
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ Room Correction and Speaker
Setup runs. This process takes a few minutes.
Please refrain from talking during
measurements and do not stand between
speakers and the microphone.
Do not disconnect the speaker setup microphone
AUDYSSEY during Audyssey MultEQ Room Correction and
Normal
Speaker Setup, unless you want to cancel the
No
Surround Back
setup.
Yes
If you select "Audyssey Quick Start", you will go
to step 9.
55) 7 Place the speaker setup microphone at the
next position, and then press ENTER.
56)
Audyssey MultEQ performs more
measurements. This takes a few minutes.
8
When prompted, repeat step 7.
® Room Correction and
En-25
Turning On & Basic Operations
9
Use / to select an option, and then press
ENTER.
MultEQ: Auto Setup
-- Review Speaker Configuration --
Subwoofer Yes
Front 100Hz
Center 40Hz
Surround 100Hz
Front High None
Surround Back 120Hz
Surround Back Ch 2ch
Save
Cancel
The options are:
Save:
Save the calculated settings and exit
Audyssey MultEQ Room Correction and
Speaker Setup.
Cancel:
Cancel Audyssey MultEQ Room Correction
and Speaker Setup.
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels
by using / .
10
Use / to select a target, and use
change the setting.
After the results of Audyssey MultEQ have been
saved, the menu will display the "Audyssey"
(➔ page 58), "Dynamic EQ" (➔ page
"Dynamic Volume" (➔ page 59) settings.
Note
• When "Audyssey Quick Start" has been used for
measurement, "Audyssey" cannot be selected.
• These settings are applied to all input selectors.
11
Press ENTER.
12 Disconnect the speaker setup microphone.
AUDYSSEY
/ to
59),