Audio Adjust - Onkyo TX-NR626 Owner's Manual

Owner's manual english
Hide thumbs Also See for TX-NR626:
Table of Contents

Advertisement

Level Calibration
This setting is set automatically by
Audyssey MultEQ
®
Room Correction and Speaker
Setup function
(➔ page
24).
Here you can adjust the level of each speaker with
the built-in test tone so that the volume of each
speaker is the same at the listening position.
Left, Front High Left, Center
, Front High Right,
*1
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
–12dB to 0dB to +12dB in 1 dB steps.
Subwoofer
*1
–15dB to 0dB to +12dB in 1 dB steps.
Note
• These settings cannot be calibrated when the AV receiver
is muted.
• Speakers that you set to "No" or "None" in
"Speaker Configuration" cannot be selected
• When the "Powered Zone 2" setting is set to "Yes" and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
*1
For the center speaker and subwoofer, the level settings
made by using the Quick Setup are saved in this menu
(➔ page
50).
Tip
• If you're using a handheld sound level meter, adjust the
level of each speaker so that it reads 75 dB SPL at the
listening position, measured with C-weighting and slow
reading.

3. Audio Adjust

With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono
Multiplex
Input Channel
Main
Sub
Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio
channels or languages with multiplex sources,
multilingual TV broadcasts, and so on.
Mono
Input Channel
Left + Right
Left
(➔ page
55).
Right
This setting specifies the channel to be used for
playing any 2-channel digital source such as Dolby
Digital, or 2-channel analog/PCM source in the Mono
listening mode.
Dolby
PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo
sources.
If you're not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro
Logic IIx.
Panorama
On
Off
En-57
Advanced Operations
With this setting, you can broaden the width of the
front stereo image when using the Dolby Pro Logic IIx
Music listening mode.
Dimension
–3 to 0 to +3
With this setting, you can move the sound field
forward or backward when using the Dolby Pro Logic
IIx Music listening mode. Higher settings move the
sound field backward. Lower settings move it forward.
If the stereo image feels too wide, or there's too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it's in mono, or there's not enough surround
sound, move it backward.
Center Width
0 to 3 to 7
With this setting, you can adjust the width of the
sound from the center speaker when using the Dolby
Pro Logic IIx Music listening mode. Normally, if you're
using a center speaker, the center channel sound is
output from only the center speaker. (If you're not
using a center speaker, the center channel sound will
be distributed to the front left and right speakers to
create a phantom center.) This setting controls the
front left, right, and center mix, allowing you to adjust
the weight of the center channel sound.
PL IIz Height Gain
Low
Mid
High
The Height Gain Control in Dolby Pro Logic IIz
enables the listener to select how much gain is
applied to the front high speakers. There are three
settings, "Low", "Mid" and "High", and the front high
speakers are accentuated in that order. While "Mid" is
the default listening setting, the listener may adjust
the Height Gain Control to their personal preference.
Operating
procedure
(➔ page 52)

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ht-rc560

Table of Contents