Rear Panel - Marantz SR5400 User Manual

REAR PANEL

z x c
COMPONENT VIDEO
ANTENNA
DVD DSS/VCR2
Y C B / C R / Y
P B P R
FM (75Ω)
GND AM
VIDEO
VCR1
TV DVD VCR1 DSS/VCR2 MONI.
TV DVD IN
IN OUT IN OUT OUT
RC-5
DIGITAL IN DIGITAL OUT
IN L
OPT. COAX.
1 2 3 4
OUT R
TV DVD VCR1 DSS/VCR2 CD TAPE CDR/MD
L
R
IN OUT IN OUT IN OUT IN
AUDIO
⁄3 ⁄2 ⁄1
z
VIDEO IN/OUT (TV, DVD, VCR1, DSS/
VCR2)
These are the video inputs and outputs. There are
4 video inputs and 2 video outputs and each one
includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
S-video sources can be viewed through the S-
video outputs, and composite sources can only be
viewed through the composite output.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
x
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked "AM" and "GND". The supplied
AM loop antenna will provide good AM reception in
most areas. Position the loop antenna until you
hear the best reception.
6
v b n
MONI.OUT
C B / C R / Y C B / C R /
P B P R P B P R
AC IN
S-VIDEO
DSS/VCR2
OUT IN OUT MONI.OUT
SL C
PRE
OUT
SR SB SW
L SL C
R L
6.1CH
IN
FRONT CENTER
OUT R SR SB SW
SPEAKER SYSTEMS
6 - 8 OHMS
⁄0 .
c
COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to
these component video connectors on the
SR5400. The SR5400 has two component video
input connectors to obtain the color information (Y,
C , C ) directly from the recorded DVD signal or
B R
other video component and one component video
output connector to output it directly into the matrix
decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra
processing that normally would degrade the image.
The result is vastly increased image quality, with
incredibly life like colors and crisp detail.
Notes:
• This component video output will not display the
OSD menu system.
v
Preamp Outputs (L, R, SL, SR, SB, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right) and SB (surround
back).
Use these jacks for connection to external power
amplifiers.
b
MONITOR OUT
This is a monitor output and each one includes
both composite video and S-video configurations.
W h e n c o n n e c t i n g t w o v i d e o m o n i t o r s o r
m
televisions, be aware that the OSD interface can
be used with both MONITOR OUT connections.
n
AC IN
Connect to supplied an AC cable, and connect to
SERIAL NO. an AC power outlet.
SR5400 has to be powered by 230V AC only.
m
AC OUTLET
AC OUTLETS
UNSWITCHED
100W MAX.
Connect the AC power cable of component such as
a DVD or CD player to this outlet. UNSWITCHED is
always live as long as the SR5400 is plugged into a
R L
live outlet.
A component connected here may be left on
SURROUND
SURROUND
BACK
permanently, or may be switched off with via its
own power switch.
Caution:
• In order to avoid potential turn-off thumps,
,
anything plugged into these outlets should be
powered up before the SR5400 is turned on.
• The capacity of this AC outlet is 100W. Do not
connect devices that consume electricity more than
the capacity of these AC outlet. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the
power supply.
,
Speaker outputs terminals
Six terminals are provided for the front left, front
right, front center, surround left, surround right and
surround back speakers.
.
Subwoofer Output
Connect this jack to the line level input of a
powered subwoofer. If an external subwoofer
amplifier is used, connect this jack to the
subwoofer amplifier input. If you are using two
subwoofers, either powered or with a 2 channel
subwoofer amplifier, connect a "Y" connector to
the subwoofer output jack and run one cable from
it to each subwoofer amplifier.
⁄0
6.1 CHANNEL INPUT
By connecting a DVD Audio player, SACD
multichannel player, or other components that has
a multichannel port, you can playback the audio
with 5.1 channel or 6.1 channel outputs.
⁄1
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
⁄2
AUDIO IN/OUT (CD, TAPE, CD-R, TV,
DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs.
There are 7 audio inputs (4 of which are linked to
video inputs) and 4 audio outputs (2 of which are
linked to video outputs). The audio jacks are
nominally labeled for cassette tape decks,
compact disc players, DVD players and etc.... The
audio inputs and outputs require RCA-type
connectors.
⁄3
DIGITAL INPUT (Dig.1 - 4) / OUTPUT
(coaxial, optical)
These are the digital audio inputs and outputs.
There are 2 digital inputs with coaxial jacks, 2 with
optical jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other
similar components.