Congratulations Thank you for purchasing your GRUNDIG VENTI TV. The following instructions will assist you in operating any of the models in the VENTI range. You may already be familiar with using a similar unit, but please take the time to read the instructions relevant for your model. Your safety is very important. Please ensure you read the “Safety Instructions” before you operate this unit. The VENTI range has been designed to give you many years of trouble‐free service. In the unlikely event that your product fails to work normally, please call one of our qualified service engineers on the below free warranty line ‐ 1800 509 394 (Australia wide). CONTENTS Unpacking & Installation Notes.…………………………………………………………………………….…….……………..‐2‐ TV Stand Installation & Wall Mount Bracket Installation ..............‐ 3 ‐ View of the TV & Functions ......................... ‐ 4 ‐ Remote Control ........................... ‐ 7 ‐ Installation & Connection ........................‐ 11 ‐ Basic Operations ..........................‐ 12 ‐ Main Menu Operations ........................- 14 - Media Player............................‐ 24 ‐ ...
Page 3
Unpacking The following items will be included with the purchase of a VENTI TV. Please refer to the correct model number outlined below for your specific accessories. If any items are missing from the below list, please contact the warranty line on 1800 509 394. LED LCD or LCD TV Remote Control DC Adaptor for LED LCD TV only Operation Manual Stand screw for LED LCD TV only Stand screws for LCD TV only Installation Notes Connect your TV to your Mains Power (AC 100‐240 Volts, 50/60). Please only connect this TV to a Mains Power that matches the power specifications (AC 100‐240 Volts, 50/60) of this TV. Locate the TV in the room where light does not directly strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Allow enough space between the TV and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure. Do not cover the ventilation openings when using the TV. ...
Page 4
TV Stand Installation The VENTI TVs come with a separated panel and base stand. Please see below detailed instructions of how to connect your stand to your TV. Place the TV with the display side down on a flat surface. Use a cloth or soft mat to protect your TV during installation. Attach the base stand at the neck as per the outline. Fix the base stand with the screw (supplied). G19LED, G22FLED, G22FLEDV, G24FLED & G24FLEDV G26LCDV, G32LCD & G32LCDV Wall Mount Bracket Installation This TV is VESA Standard wall mountable. Please see below image of the 4 VESA standard holes (G19LED, G22FLED, G22FLEDV, G24FLED and G24FLEDV ‐ 100mm x 100mm) (G26LCDV ‐ 200mm x 100mm, G32LCD and G32LCDV ‐ 400mm x 200mm). The wall mount bracket and screws are not included with your TV. The wall bracket may be purchased from your local retailer. To attach your bracket use the 4 holes provided to screw your bracket to your TV. You will also have to remove the base stand and neck. ‐ 3 ‐...
View of the TV & Functions Front View Side View G22FLEDV / G24FLEDV G26LCDV / G32LCDV ...
Page 6
TV Key Functions Back LED LCD TV Key Functions Remote Sensor (G19LED, G22FLED, G22FLEDV, G24FLED & G24FLEDV) Receives the remote signals from the remote 11. RF Input control. To connect the external aerial. Power Indicator 12. VGA Input The VGA Input allows you to connect your TV to In Power On Mode the indicator will turn Blue. your PC to use as a monitor. In Standby mode the indicator will turn Red. 13. AV Output Source The AV Output allows you to connect the unit to Press the SOURCE Button to display the input external video system. source list and then press Vol+/‐ to select the 14. PC Audio Input input source. The PC Audio Input allows you to connect your TV to your PC to use as a monitor and enable the MENU sound for movies etc. Press the MENU Button to display the Main 15. USB Input Menu. In main Menu, you can use the Vol+/‐ or The USB Input enables you to insert your USB or CH+/‐ Buttons to find and select different sub ...
Page 7
Back LCD TV Key Functions 18.Audio Input (G26LCDV, G32LCD & G32LCDV) The Audio Input (Left and Right) must be 11. AV2 Input connected with the white and red cable for a The AV2 Input allows you to connect any audio composite connection. visual accessory to play on this TV. 19. YPbPr Input 12. USB Input The YPbPr Input must be connected for a The USB Input enables you to insert your USB component connection. or Hard Disc to record live TV or to play Music, 20. AV1 Input Video or Image files. It can also be used for The AV Input must be connected with the software upgrades. yellow cable in both composite and 13. AC Input component connections. The AC Input allows you to connect your main 21.HDMI Input power source. The HDMI Input allows you to connect 14.RF Input your HDMI Cable for greater definition. To connect the external aerial. 15.VGA Input The VGA Input allows you to connect your TV to ...
Page 9
Remote Control Key Functions – G19LED, G22FLED, G24FLED & G32LCD 1. Standby Button: Press the Standby Button to switch the TV on or off. 2. Rewind / Subpage Button: Press the Rewind Button to rewind play in USB or Time shift mode. In Teletext mode, it is used as Subpage. 3. ►► Fast Forward / Reveal Button: Press the Fast Forward Button to fast forward play in USB or Time shift mode. In Teletext mode, it is used as Reveal. 4. ► Button: Press the Play Button to play the files in USB mode or to resume play after pausing in Time shift mode. Press the Play Button again to enter A‐B playback mode. 5. II Button: Press the Pause Button in USB or Time Shift mode to pause play of files or live TV. 6. TEXT Button: Press the Text Button to enter the Teletext Menu. 7. Subtitle Button: Press the Subtitle Button to turn ON or OFF the subtitle feature. 8.
Page 11
Remote Control Key Functions – G22FLEDV, G24FLEDV, G26LCDV & G32LCDV 1. Standby Button: Press the Standby Button to switch the TV on or off. 2. EJECT Button: Press the Eject Button to load or unload your DVD disc. 3. TITLE Button: Press the Title Button to enter the Title menu in DVD mode. Rewind / Subpage Button: Press the Rewind Button to rewind play in USB, DVD or Time shift mode. In Teletext mode, it is used as Subpage. 5. ►► Fast Forward / Reveal Button: Press the Fast Forward Button to fast forward play in USB, DVD or Time shift mode. In Teletext mode, it is used as Reveal. 6. II Button: Press the Pause Button in USB, DVD or Time Shift mode to pause play of files or live TV. 7. ► Button: Press the Play Button to play the files in USB/DVD mode or to resume play after pausing in Time shift mode. Press the Play Button again to enter A‐B playback mode. 8. TEXT/RETURN Button: Press the Text Button to enter the Teletext Menu in DTV mode. In DVD mode, press it to return to the Main Menu (PBC ON only). 9. Subtitle Button: Press the Subtitle Button to turn ON or OFF subtitles in DTV mode. In DVD mode, press the Subtitle Button select the caption options offered by the DVD playing. 10. MENU Button: Press the Menu Button to enter the Main Menu. 11. Navigation Buttons: Press the Navigation Buttons to scroll through menu options. 12. OK Button: Press the OK Button to confirm any settings selected or press to display the Channel List in TV mode. 13.
26. DISPLAY Button: Press the Display Button to show the information of the current playing disc. 27. SOURCE Button: Press the Source Button to show the Source List. 28. EXIT Button: Press the Exit Button to exit Menu settings. 29. CH+ / CH‐ Button: Press the Ch+ /CH‐ Button to scroll through the channel list. 30. REC / REP Button: Press the REC Button to record a TV program or press the REC Button in USB/DVD mode to select repeat during playback. 31. RECALL/GOTO Button: Press the Recall/GOTO Button to return to the previous channel viewed in DTV mode. In DVD mode, press the Recall/GOTO Button to choose the desired title, chapter or to search the desired title time and chapter time. For super VCD and CD discs press this Button to search the desired disc time and track time and choose the desired track. Note: During VCD playback, the PBC mode must be set to OFF. Remote Control Battery Installation The remote control requires two AAA batteries. Below are steps to assist you with replacing the batteries. 1. Open the back cover of the battery compartment. 2. Install the batteries into the battery tray. There is +/‐ polarity marking in the battery compartment. Please ensure the polarity is correct. 3. Close the battery cover. Caution: ...
or Camcorder (cables not supplied). 5. AV Output allows you connect your TV with another monitor or TV sets when it is in DVD or TV mode. 6. VGA Input can be connected with the VGA Output of your PC to use this TV as a monitor. There is also a PC Audio Input for your connection with PC, see image below. 7. Connect your TV to your Mains Power (AC 100‐240 Volts, 50/60). Please only connect this TV to Mains Power that matches the power specifications (AC 100‐240 Volts, 50‐60 Hz) of this TV. 8. For the LCD Models only, press the main power switch on the back of unit to turn on your TV to Standby mode. You then must press the Standby Button on remote control to turn on your TV. Please note: After AV, YPBPR or HDMI is selected ensure the Video Output from your connected accessory (for example DVD player) is set to corresponding video mode. AV and YPbPr share the same Right/Left Audio Input. Basic Operations 1) Press the STANDBY Button on the unit or remote control to turn the TV on or off. Please note: For the LCD models, you are required to press the main power switch on the back of unit before pressing the Standby Button on your remote control. 2) If you are using the TV for the first time, the Installation Guide below will be displayed to guide you through the initial channel scan. Press the Navigation Buttons to the prompted options i.e. language or Country. Then press the OK Button to confirm. When you have selected the options in the Installation Guide, DTV Auto Tuning will then start automatically. You may press the Menu Button to skip ATV for DTV tuning. ...
Page 14
3) After auto tuning, the amount of programs found and stored will be shown on the display and the first channel will begin to play automatically. 4) To change between Digital TV (DTV) and Analog TV (ATV), press the SOURCE Button on the remote control to select the preferred mode. 5) To change the channel in either mode, press the CH+/CH‐ Button or press the OK Button in TV mode to display the Channel List. Then press the UP/DOWN Navigation Buttons to select the channel you want to watch and press the OK Button to confirm the highlighted channel. You can also press Numeric Buttons on remote to select the channel directly. To go back to the last channel you were watching you can press the RECALL Button on the remote control. 6) To change the source input to watch a connected accessory, press the SOURCE Button and then press the ▲or ▼ Navigation Buttons to scroll through and select the available input source. 7) To adjust the volume, press the VOL+/‐ Button to increase or decrease the sound level. 8) Press the MUTE Button to turn off the sound only and press it again to turn on the sound again. 9) Press the INFO Button to display the information of the channel playing. Press the Up or Down arrows to ...
5. Press the Subpage Button (certain pages contain sub‐pages which are automatically displayed) to stop or resume sub‐page acquisition the indication appears top left. 6. Press the REVEAL Button to display or hide the concealed information. 7. Press the SKIP FORWARD/LIST Button to set four favourite pages directly linked to the four color keys. While list mode is activated, it is not possible to use the Top or SFLOF navigation with the colour keys. Main Menu Operations Press the MENU Button and then the Navigation Buttons on the remote control to select the sub‐Menus or the options you want to change. Then press the OK Button to confirm. Press the MENU Button when you want to return to the previous Menu, and press the EXIT Button to exit Menu setting. Channel Menu The TV Channel Menu will allow you to change the channel setting or search for new or weak stations with access to Auto Tuning, ATV Manual Tuning, DTV Manual Tuning, Program Edit and Signal Information. To enter the TV Channel Menu press the MENU Button and the Channel Menu will appear. Press the OK Button to enter. Press the ▲or▼ Buttons to select a below sub‐Menu and then press the OK Button to confirm. To exit the Channel Menu, press the Menu Button. Auto Tuning Once Auto Tuning is selected, you will see an OSD below. Tune Type is highlighted above. Press the Navigation Buttons to select DTV, ATV or ATV+DTV tuning type and Country (Australia is the default).Then press the OK to confirm and Auto Tuning will begin automatically. During Auto Tuning you can press the MENU or EXIT Button to exit. ‐ 14 ‐...
Page 16
DTV Manual Tuning Use the ▼ or ▲ Buttons to select DTV Manual Tuning in the Channel Menu. Then press the ◄or ► Buttons to select the individual DTV channel you wish to store and press the OK Button to begin search. Press the Menu Button to return to previous Menu or press the EXIT Button to exit. ATV Manual Tuning Use the ▼ or ▲ Buttons to select ATV Manual Tuning in the Channel Menu. Then press the ◄or ► Buttons to select the individual ATV channel (frequency) you wish to store. Then use the Arrow Buttons to highlight the search option and press ok, this will activate the manual tune. If the picture is not so clear you can use the Arrow Buttons to highlight the Fine‐Tune option and select Fine‐Tune. Press the RED Button to save. Notes: You need to set the Sound System before manual tuning. For Australia, Sound system is BG. Program Edit Press the ▲or▼ Buttons to select Program Edit in the Channel Menu. Then press the OK Button to enter the sub‐Menu. Then you will need to select the program you wish to edit. ‐ 15 ‐...
Page 17
Delete: Press the Red Button to delete the channel you highlighted. Rename: (For ATV only) Press the Green Button for renaming the channel. Press the Navigation Buttons to enter a new name and press the OK Button to confirm. MOVE: Press the Yellow Button to move the selected channel. Then press the Numeric Buttons to enter new channel number and press the OK Button to confirm. SKIP: Press the Blue Button to select the Skip function and a SKIP icon will be displayed next to the program and it will be skipped when changing the channel. FAV: Press the FAV Button (instead of color Buttons) to set the favourite channel. Note: If you want to view the Favorite Channel List you need to exit Program Edit Menu and then press the FAV Button. Signal Information (Only for DTV) Press the ▼ / ▲ Buttons to select the Signal Information in the Channel Menu. Then press the OK Button to show the related information of the current channel. Software Updated (USB) Press the ▼ or ▲ Buttons to select Software Update (USB) in the Channel Menu. Then press the OK Button to update software by using a USB. Follow the software upgrade instructions provided with the software. Note: We recommend you perform a factory reset (refer to Restore Factory Default in OPTION menu) to ensure the unit is successfully upgraded. Picture Menu To enter the Picture Menu, press the MENU Button and then press the ◄ or ► Buttons to select the Picture Menu. Press the OK Button to enter. Once in the Picture Menu, press the ▲ or ▼ Buttons to select the options you wish to adjust. Press the OK Button to enter the sub‐Menu. To return to the Main Menu, press the MENU Button, or press the EXIT Button to exit. ‐ 16 ‐...
Page 18
Picture Mode There are four different Picture modes: Standard, Mild, Dynamic and User. You are only able to set the Contrast, Brightness, Colour or Sharpness in User mode. To change the Picture Mode, press the OK Button to enter the submenu and then press the ▲ or ▼ Buttons to scroll through the picture modes. Press the OK Button to confirm. Contrast: Press the ◄ or ► Button to adjust the contrast. Brightness: Press the ◄ or ► Button to adjust the brightness. Colour: Press the ◄ or ► Button to adjust the colour. Sharpness: Press the ◄ or ► Button to adjust the sharpness. Tint: Press the ◄ or ► Button to adjust the tint, this option only works in VGA mode and when the VGA input is connected. Colour Temperature: Press the ◄ or ► Button to scroll through the colour temperature: Cold, Medium, user and warm. Aspect Ratio: There are three aspect ratios: 16:9, 4:3 and Auto. Noise Reduction: Press the ▲ or ▼ Button to scroll through the Noise Reduction options. You can set Noise Reduction to Off, Low, Middle, High, and Auto. Screen: This option is for PC Mode only. Please refer to the PC section of the manual. Sound Menu To enter the Sound Menu, press the MENU Button, then press the ◄ or ► Button to select the Sound Menu and press the OK Button to enter. Once in the Sound Menu, press the ▲ or ▼ Button to select the options you wish to adjust. Press the OK ...
Page 19
Sound Mode There are four Sound modes: Standard, Music, Movie, Sports and User. You are only able to set Treble, Bass in User mode. To change the Sound Mode, press the OK Button to enter the submenu and then press the ◄ or ► Buttons to scroll through the sounds modes. Press the OK Button to confirm. Treble: Press the ◄ or ► Button to adjust the treble. Bass: Press the ◄ or ► Button to adjust the bass. Balance: Press the ◄ or ► Buttons to adjust the balance of left and right audio outputs. Auto Volume: Press the OK Button to select Auto Volume to on or off. When it’s set to on, the volume level will stay as the set Volume. Audio Description: This feature allows you to listen to an audio commentary of non verbal actions that appear on‐screen. Audio Description includes spoken descriptions of; body language, expressions and movements. This feature is particularly helpful for low vision or blind users to still be able to utilise their VENTI TV. In the sound menu you can turn on Audio Description and adjust the sound level by pressing the ◄ or ► Buttons. Please note: Audio Description is only available in DTV mode and when broadcast by the local station. Time Menu (in TV mode only) To enter the Time Menu, press the MENU Button, then press the ◄ or ► Button to select the Time Menu, and press the OK Button to confirm. Press the ▲ or ▼ Button to scroll through the options in the Time Menu. Press the OK Button to enter the sub‐menu. To return to the Main Menu, press the MENU Button or press the EXIT Button to exit. ‐ 18 ‐ ...
Page 20
Clock: The Clock is updated by DTV program. Off Time / On time: Once the On or OFF timer is set to ON, you may set the auto OFF or ON time personally. This will enable you to have the unit turn on or off at as selected time. Sleep Timer: You can set the Sleep Timer to OFF, 10mins, 20min, 30min, 60mins, 90mins, 120mins, 180mins or 240mins, press the ▲ or ▼ Button to scroll through and select the available time. The TV will automatically turn to Standby when sleep time is set. Auto Sleep: You can set the TV to Auto Sleep is not active after select time period. Press the ▲ or ▼ Button to scroll through and select the available time. Time Zone: You can set the Time Zone here. The default is New South Wales GMT +10. Option Menu To enter the Option Menu, press the MENU Button, then press the ◄ or ► Buttons to select the Option Menu, and press the OK Button to confirm. Press the ▲ or ▼ Buttons to scroll through the options in the Option Menu. Press the OK Button to enter the sub‐Menu. To return to the Main Menu, press the MENU Button or press the EXIT Button to exit. OSD Language Press the ▼ or ▲ Buttons to select OSD Language. Then press the OK Button to enter sub‐Menu. Then use the ▼, ▲, ◄ or ► Buttons to select the language. The default language is English. Audio Language Press the ▼ or ▲ Buttons to select OSD Language. Then press the OK Button to enter sub‐Menu. Press the ◄ or ► Buttons to select the primary or secondary language. Then use the ▼, ▲, ◄ or ► Buttons to select the language. The default language is English. PVR File System (only for DTV) Press the ▼ or ▲ Buttons to select PVR File System, then press the OK Button to enter sub‐Menu and then use the ▼ or ▲ Buttons to scroll through the options. Select Check PVR File System and then press the OK Button to enter. This function will check the USB speed. ...
Page 21
Select Disk If you are using a Hard Disc Drive for recording and your Hard Disc Drive has more than 2 partitions, you are able to select ONE Partition for recording. You can press the OK Button and then the right or left Button to select the particular partition for recording. For example C or D partition, etc. The recording file will be saved in the partition you selected. If you are using a USB device for recording, you can only select USB for recording. Check PVR File System Here is where you are able to check your USB or Hard Disc Drive format and see if the USB or Hard Disc Drive you are using is compatible. If your USB or Hard Disc Drive is not compatible, you will see FAIL on the screen. You will then need to format the device. If it is compatible then "SUCCESS" will be displayed. Note: You will ONLY be able to perform program recording when your Hard Disc Drive or USB device is shown as compatible. If it is not compatible you will need to use another USB or Hard Drive that is compatible. Format There are two types of format: FAT32 and Hi Speed Format. Press the Right or Left Navigation Buttons to select your type of recording format. Once you select Hi Speed or FAT32 format, you are able to press the Right or Left Buttons to select the size you ...
Page 22
Do NOT unplug your Hard Disc or your USB device during formatting or it will damage your device. Speed If the speed of your Hard Disc Drive or USB device is too low, it will not be compatible with this TV and FAIL will be displayed on the screen. You will not be able to record with the incompatible device. Free Record Limit After formatting is complete, the unit will internally calculate the approximate number of hours your Hard Disc Drive or USB device can use for recording. You can check this in this menu. Restore Factory Default Press the ▼ or ▲ Buttons to select Restore Factory Default and press the OK Button to enter the guide. Once confirmed, all the settings will be cleared. This should be used if you experience any issues with your TV. Lock Menu To enter the Lock Menu, press the MENU Button, then press the ◄ or ► Button to select the Lock Menu, and press the OK Button to enter. ‐ 21 ‐ ...
Page 23
Lock System Press the OK Button to enter. You will be asked to input your password or the default password to activate this setting. The default password is “6666”. Note: When the Lock System is set to ON, you will be need to enter your password or the default password to conduct a station rescan or to restore the TV to it factory settings. Set Password To change the password, press the OK Button to select ‘Set Password’ and a pop‐up Menu will appear to enter your new password. The default password is “6666”, you will need this in order to set your new password and follow the onscreen prompts. Block Program To block a program from being watched, select Block Program and press the OK Button to enter the program list. Press the ▲ or ▼ Buttons to select the channel you want to block and then press the Green Button to block. The block icon will appear behind the blocked channel. To un‐lock the channel, select the blocked channel and press the Green Button again, the lock icon will disappear. Parental Guidance Select ‘Parental Guidance’ and press the OK Button to enter the sub‐Menu. In this Menu you will be able to set the program rating and block selected rating/programs from view. Hotel Lock To turn on the Hotel Lock feature, you must select the Hotel Lock sub‐Menu in the Lock Menu and press the OK Button to enter. Then press the ◄ or ► Buttons to set the feature on ON or OFF. Press the OK Button to confirm. ‐ 22 ‐ ...
Page 24
Lock Channel: Once Lock Channel is set to on, you will be able to lock a specific channel from being viewed, scanned or edited and can only be changed after a password has been entered. Set Source: Once Set Source has been set to on the unit will be locked on the current source mode and a password will need to be entered to change the TV source mode. Channel Number: In either DTV or ATV mode only, you can select a channel number to be set as the TVs preset channel. Press the ◄ or ► Buttons to select the desired channel number and it will be set as the preset channel and automatically turn on when the TV is turned on. Picture Lock: Once Picture Lock is set to ON the Picture settings will not be able to be adjusted without a valid password. Key Lock: When Key Lock mode is on, all buttons including the Standby Button on the side of unit will be locked from operation. Max Volume: This option allows you to set the Max Volume Level. Source Lock: This option allows you to lock specific source modes from being used (refer to the image on the next page). To set the Source Lock option, press the OK Button in the Hotel Lock Menu to enter the Source Lock sub‐Menu. Then use the Navigation Buttons to scroll through the source options and highlight the modes you would like to change. Press the ◄ or ► Buttons when a mode is highlighted to set the option as ON or OFF. If the option is set as ON the mode will be lock from operation. Please note: DTV and ATV modes can’t both ON at the same time. ‐ 23 ‐...
Clear Lock: This option allows you to clear all lock settings. Press the OK Button to confirm. Media Player To playback media files from your USB/HDD or to playback recorded programs, press the Source Button on your remote control and then select the Media Player option. Make sure your USB/HDD is connected to the USB input on the side of your TV. Once your USB/HDD is connected, press the ◄ or ► Buttons to select the media mode you wish to play. Recorded TV files can be played via the movie option. Press the OK Button to enter the selected media mode and your storage device files will be displayed on screen (see below). ...
Press either the ▼ or EXIT Button to exit the control bar. When playing a movie file, you can press the Fast Forward Button to skip forward in the file or press the Rewind Button to skip backwards to a previous section of the movie. When viewing a text file you can press the I<< or >>I Buttons to move up and down the page. To return to the Media Menu press the MENU Button or press the EXIT Button to exit. You can also delete files from your USB/HDD in media mode. Highlighted the files you would like to delete and press the RED Button. The selected files will be deleted from both the screen and your storage device. Please Note: We recommend using a powered Hard Disc Drive, please ensure the external power adaptor is firmly connected. If you find that your Hard Disc Drive is still not supported in media player mode it may be due to the power size of your device. EPG Menu The EPG (Electronic Programme Guide) Menu provides you with detailed broadcast program information. Press the EPG Button and a pop‐up Menu will be displayed with program information about the channel you are currently watching. You will be able to see up to eight days of program information. To view the next day or more use the Navigation Buttons to highlight the date and then press the I<< or >>I Buttons to scroll through the available dates. ...
Page 27
end time of recording rely on the broadcast programming. When the recording has been set to Once, Everyday or Weekly, you will be able to set the start time and end time for recording. Notes: Please ensure a compatible Hard Disc Drive or USB device is inserted into the USB input to scheduled recordings. If your storage device is not compatible, you will be asked to format it. Press the MENU Button to enter the PVR File System Menu to format your device. If you have set a timed recording, your TV will automatically turn on when the program is set to record and will automatically turn off after the recording is complete. During a timed recording however the picture and volume will be mute (there will be no display), however the unit will be on. You can press the STANDBY Button to turn the picture and volume back on. INFO (Green Button) In the EPG Menu, press the GREEN Button to view more information about the current program. Schedule (Yellow Button) In the EPG Menu, press the YELLOW Button to view the schedule list, this will display all programs set for reminder (identified by a clock icon) or set for recording (identified by a movie icon). If you want to delete a set recording or reminder, press the Navigation Buttons to highlight the item and then press the RED Button to delete. Remind (Blue Button) In the EPG Menu, press the BLUE Button to set a program reminder. The below Reminder Menu will then be displayed and you can use the ◄or ► Buttons to set the program reminder details. You will be able to set ‐...
reminder to occur Once, Everyday or Weekly. When the program is on that you would like to watch a pop up reminder will be displayed on screen. DTV Recording To record the program you are currently watching press the REC Button and a red REC icon will appear on the screen. The record time/ length and remaining record time will be displayed in the menu below. To conceal or reveal the menu press the REC Button again. To stop recording, press the Stop Button or move the cursor to select the Stop option when the above menu is displayed and then follow the pop‐up guide. To play what you have recorded when the recording is still in process or after the recording has finished press the Recorded List Button to view your recorded programs. Then use the navigation buttons to select the program you wish to play and press the OK Button to confirm. You may also enter the Media Player Menu to view your recorded programs via Movie mode. Notes: Ensure the storage device used to record is inserted into the USB Input on the back of the unit and is compatible for recording. If your storage device is not compatible, you will be asked to format it. Press the ...
Time Shift Press the ►II Button to pause the program you are watching to activate Time Shift function. The below menu will be displayed. This Menu will auto disappear after several seconds. Press the ►II Button again to resume playing, and a white play icon will appear at the left of the screen, which shows that time shift is being performed. To conceal or reveal the menu press EXIT Button. To stop time shifting, press the Stop Button or move the cursor to select the Stop option when the menu is on, and then follow the pop‐up guide. Notes: Ensure the storage device used for recording is inserted into the USB Input on the back of the unit and is compatible for recording. If your storage device is not compatible, you will be asked to format it. Press the MENU Button to enter the PVR File System to format your device. All the functions (Play, FB, FF, Prev., Next, Pause and Stop) in the menu can only be performed when the menu is on. You may directly press the Button or move the cursor to select the option when the menu is on ...
the ◄ / ► Button to adjust. V‐Offset Press the ▼ / ▲ Buttons to select V‐Offset, then press the OK Button to enter sub‐Menu. Press the ◄ / ► Button to adjust. Size Press the ▼ / ▲ Button to select Size, then press the OK Button to enter sub‐Menu. Press the ◄ / ► Button to adjust display size. Phase Press the ▼ / ▲ Button to select Phase, then press the OK Button to enter sub‐Menu. Press the ◄ / ► Button to adjust. Notes: Noise Reduction in PICTURE option is invalid. SOUND Menu, LOCK Menu and description are the same as that for DTV mode. TIME Menu has no clock option. Hearing Impaired and PVR File System in OPTION Menu are invalid. DVD Player Operation (G22FLEDV, G24FLEDV, G26LCDV & G32LCDV Only) This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited. 1. Press the SOURCE Button on the remote control to select the DVD mode. Insert a disc (DVD, CD or MP3) into the slot of DVD player from the right side. It will start to read the disc automatically. Press the EJECT Button on the remote control, the disc will automatically eject. Note: Insert the disc with reflective data side facing to the front of the TV. Some slight picture and sound noise are produced when the disc is loading, unloading and during playback. This is normal and can be ignored. 2. If you are playing a DVD disc, press the MENU/INFO Button to enter the DVD Play Menu. 3. If you are playing a CD or MP3 disc, the table playing guide below will display. Press the Navigation Buttons to select the folder or file you want to play and then press the OK Button. You may also set the Filter, Repeat mode and enter Edit mode for programming playback. Language Setup Press the DVD Setup Button to enter the Language Setup Menu. You will be able to change the OSD, Subtitle, Audio and DVD Menu language here. Please note that English is the default language. Also please note that not ‐ 29 ‐...
Page 31
some discs will not support MPEG4 subtitle. Video Setup Press the DVD Setup Button and then Navigation Buttons to switch to Video Setup Menu. Aspect Ratio In the Video Setup Menu you are able to select the DVD mode aspect ratio, you may choose from one of the three aspect ratios: 4:3 PS / 4:3LB / 16:9. This will also be dependent on the requirements of your disc format. TV System In the Video Setup Menu you are able to select the DVD mode picture format. You will be able to choose between NTSC, PAL or AUTO. Rating Setup Press the DVD Setup Button and then the Navigation Buttons to switch to Rating Setup Menu in DVD mode. Upon entering this Menu you will be asked to enter your password. You must enter your set password or the default password ‐ 6666. This section will allow you to set a control lock of select DVD ratings. Misc Setup ...
Troubleshooting If you have any issues or queries about the functions of this TV, please check the below table as we have provided you with FAQs to assist with any issues or visit our FAQ page online – www.grundig.net.au. If this table is not of assistance, please contact the Grundig Warranty line on 1800 509 394. Issue Solution No power Turn off the unit at the remote and at the wall socket. Pull out the power plug. Wait 60 seconds and then plug the power cord back in, turn the power and unit back on. No picture Check that your cables and antenna have been connected firmly. Check that your Picture Settings are correct. Conduct a restore setting to return settings back to the factory default. No sound Check that your audio cables have been connected firmly. Check that Muted Audio is not on and that Audio Settings are correct. Conduct a restore setting to return settings back to the factory default. Colour distortion Ensure that the equipment is connected properly. Ensure that the AV video signal Input is connected properly. Remote control is Check the batteries and make sure there are no obstacles in the way of not responding the remote control and the sensor on the television. Move closer to the remote sensor. Using a digital camera (such as an iPhone camera) point the remote control facing the camera from about 10 cm away. If you see a purple flash each time you press the remote control then your remote control is working. Screen glittering Reset the computer and enter the safety mode, then select the under PC mode appropriate screen type by consulting the PC operation manual. ...
Safety Instructions Please read these operating instructions carefully before you operate this unit. 1. Clean with a dry cloth only, to clean up dust, water drops or smudges from the screen or cabinet. Also make sure you disconnect the TV when you are cleaning the unit. 2. Do not block any ventilation openings. Install in accordance with the manufacturers’ instructions. 3. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. 4. Protect the power cord from being walked on or pinched. 5. Only use attachments/accessories specified by the manufacturer. 6. Unplug this TV during lightning storms or when unused for long periods of time. 7. Refer all servicing to qualified service personnel. Servicing is required when the TV has been damaged in any way, such as the power‐supply cord or plug has been damaged, liquid has been spilled or objects have fallen into the TV, the TV has been exposed to rain or moisture, does not operate normally, or has been dropped. 8. The TV should not be exposed to dripping or splashing water and no objects filled with liquids, such as vases, should be placed on the TV. 9. If the TV is to be built into a compartment or an enclosed space, heat build‐up can occur and can reduce the service life of your TV and can be dangerous. Make sure you leave plenty of space around the unit. 10. If there is a sudden change in temperature or humidity, or when warm air comes into contact with any cold parts in the unit, condensation may form. Placing the unit in a warm room to dry out any condensation, this may take 1 to 2 hours, depending on environmental conditions. Once condensation disappears, the unit will return to normal functions. 11. Never tamper with any components inside the TV, or make any adjustment not mentioned in this manual. 12. During thunder and lighting, unplug the power cord and antenna cord to prevent damage to your TV. 13. Be cautious of this safe mark ...
Warranty Please keep your receipt as proof of purchase. This product is warranted for any defect in materials or workmanship for 12 months after the original date of purchase. This product is for normal domestic and office use only. This warranty does not cover damage from misuse or neglect , accidental damage, vermin infestation, excessive voltages such us lightning or power surges or any alternation that affects the performance or reliability of the product. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. In the unlikely event that your product fails to work normally, please contact Grundig Warranty on 1800 509 394 (Australia) or 0800 450 259 (New Zealand) and have your receipt of purchase on hand. This guarantee is subject to the following provisions: ● It is only valid within bounda ries of the country of purchase ● The product must be correctly assembled and operated in accordance with the instructions contained in the manual ● This product must be use d solely for domestic purposes ● The guarantee d oes not cover accidental damage ●...
Page 41
PO BOX 6287 Silverwater NSW 1811 www.grundig.net.au Grundig Warranty: 1800 509 394 Australia Grundig Warranty: 0800 450 259 New Zealand ...