Packard Bell EasyNote DT85 Service Manual
  1. Manuals
  2. Brands
  3. Packard Bell Manuals
  4. Laptop
  5. EasyNote DT85
  6. Service manual

Packard Bell EasyNote DT85 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EasyNote DT85
SERVICE
GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Packard Bell EasyNote DT85

Summary of Contents for Packard Bell EasyNote DT85

  • Page 1 EasyNote DT85 SERVICE GUIDE...

  • Page 2: Revision History

    Service guide files and updates are available on the ACER/CSD web. For more information, refer to http://csd.acer.com.tw Copyright © 2009 Packard Bell is a registered trademark of Packard Bell BV. All rights reserved. All other brands and product names are trademarks or registered trademarks of their respective companies.

  • Page 3: Table Of Contents

    Contents Chapter 1: System specifications ........1 Preface ..........2 Conventions .
  • Page 4 Contents Creating the Crisis Recovery disk ....41 Performing a BIOS recovery ......41 Running the Flash utility: .
  • Page 5 www.packardbell.com Replacing the LCD assembly lid ......134 Chapter 4: Troubleshooting ........137 Diagnosing problems .
  • Page 6 Contents Appendix C: Online support information ......195 Online Support Information ......196...

  • Page 7: Chapter 1: System Specifications

    CHAPTER1 System specifications • Preface • Features • System block diagram • Hardware specifications • Notebook product tour • Keyboard • Touchpad • Webcam...

  • Page 8: Preface

    CHAPTER 1: System specifications Preface Conventions The following conventions are used in this manual: Warning Indicates a potential for personal injury. Caution Indicates a potential loss of data or damage to equipment. Important Indicates information that is important to know for the proper completion of a procedure, choice of an option, or completing a task.

  • Page 9: Features

    www.packardbell.com Features Platform ® • Intel – Processor: Intel Core™2 Duo processor (2.0–2.4 GHz or above) with 1066/800 MHz FSB – Core logic: Intel GM45 (north bridge) + Intel ICH9M (south bridge) • Wireless: Intel WiFi Link 5100 a/b/g/n, Lite-On Atheris b/g/n System memory •...

  • Page 10: Input Devices

    CHAPTER 1: System specifications Input devices • 99-,100-, or 103-key keyboard, 2.5 mm (minimum) key travel • Function keys, system keys, navigation keys, Fn key, Windows key, Application key, arrow keys, and a separate numeric keypad • Touchpad pointing device •...
  • Page 11 www.packardbell.com Security • Kensington lock • BIOS-based user, supervisor, and HDD passwords Physical specifications • Dimensions: 441.1 × 300 × 40.2/44.2 mm (17.37 × 11.81 × 1.58/1.74 in) • Weight: 4.1 Kg. (9.04 lbs.) Environment • Temperature – Operating: 32 to 90 °F (0 to 35 °C) –...

  • Page 12: System Block Diagram

    CHAPTER 1: System specifications System block diagram...

  • Page 13: Hardware Specifications

    www.packardbell.com Hardware specifications Processor Item Specification Type Intel Core 2 Duo, Pentium Dual-Core, Celeron mobile processor Processor package Socket-P, µFCPGA Processor core voltage 1.0375V to 1.3V Core logic Intel GM45 + ICH9M Controllers Item Intel platform Core logic Intel GM45 + ICH9M •...

  • Page 14: Bios

    CHAPTER 1: System specifications BIOS Item Specification BIOS vendor Phoenix BIOS version V1.01 BIOS ROM type BIOS ROM size 16 Mb BIOS package 8-SOP Supported protocols ACPI 1.0b/2.0/3.0 compliance, PCI 2.2, System/HDD Password Security Control, INT 13H Extenstions, PnP BIOS 1.0a SMBIOS 2.4, BIOS Boot Specification, Simple Boot Flag 1.0, Boot Block, PCI Bus Power Management Interface Specification, USB Specification 1.1/2.0, IEEE 1394 1.0, USB/1394 CD-ROM Boot Up support, PC Card Standard 1995 (PCMCIA 3.0 Compliant Device), IrDA 1.0, Intel AC97 CNR...

  • Page 15: Hard Drive

    www.packardbell.com Hard Drive Item Specification Model Seagate Seagate Seagate Seagate ST9160310AS ST9250315AS and ST9320320AS ST9500325AS ST9250320AS Toshiba Toshiba Toshiba MK1655GSX Toshiba MK2555GSX MK3255GSX MK5055GSX Hitachi Hitachi Hitachi Hitachi HTS543216L9A30 HTS545025B9A300 HTS545032B9A30 HTS545050B9A30 Western Digital Western Digital WD2500BEVT-22ZCT Western Digital Western Digital WD1600BEVT-22Z WD3200BEVT-22 WD5000BEVT-22Z...

  • Page 16: Lcd

    CHAPTER 1: System specifications Item Specification Transfer rate Sustained: Sustained: • with CD: Max 3.6 Mbytes/sec • with CD: Max 3.6 Mbytes/sec • with DVD: Max 10.08 Mbytes/sec • with DVD: Max 10.8 Mbytes/sec • with BD: Max 11 Mbytes/sec Buffer memory 2 MB •...

  • Page 17: Audio

    www.packardbell.com Item Specification Display mode Normally white Brightness (nits) 250 / 220 Luminance uniformity 1.25 max. Contrast ratio 400–500 typical Response time (ms) Nominal input voltage +3.3 V Viewing angle Horizontal: Right/Left 45/45 Vertical: Upper/Lower 15/35 Temperature (°C) Operating 0 to +50 Storage (shipping) -40 to +60 Audio...
  • Page 18 CHAPTER 1: System specifications Item Specification Features • Intel Gen 5.0 integrated • graphics engine with ten, fully-programmable cores • Supports HDMI/DVI, DP, TV-Out, LVDS, CRT and SDVO ® • Intel Dynamic Video Memory Technology (Intel® DVMT 5.0) • Video Capture via x1 concurrent PCI Express port •...

  • Page 19: Keyboard

    www.packardbell.com Keyboard Item Specification Controller Winbond WPC773 Type 99- ,100 or 103-key, 2.5 mm (minimum) key travel Key types Function keys, system keys, navigation keys, Fn key, Windows key, Application key, arrow keys, and separate numeric keypad Capacitive hotkeys Caps lock, Num lock, PowerSave, My Backup, Wi-Fi control, touchpad lock, and volume controls Support for simultaneous use of Internal and external...

  • Page 20: Wired Lan

    CHAPTER 1: System specifications Wired LAN Item Specification Chipset Broadcom BCM5784 Data throughput 10/100/1000 Mbps LAN connector type RJ45 LAN connector location Left side Features • Integrated 10/10/1000 BASE-T transceiver • PCI v2.2 compliant • Wake on LAN support meeting ACPI requirements Wireless LAN Item Specification...

  • Page 21: Usb

    www.packardbell.com Item Specification Chipset • Intel ICH9M USB compliancy level OHCI USB 1.1 and USB 2.0 host controller Number of USB ports Location • Two on the left side • Two on the right side Buttons/Indicators/Ports Item Specification Buttons • Power button •...

  • Page 22: Cooling Fan

    CHAPTER 1: System specifications Cooling fan Processor temperature (°C) Fan speed (rpm) Acoustic level (dBA) 45-50 0-3000 55-66 0-3300 68-74 3300-3800 78-83 3800-4100 86-91 4100-4800 Note: Throttling 50%: % is controlled by operating system. Temperature point is 95 °C. OS shut down at 100 °C; Hardware shut down at 105 °C Battery Item...

  • Page 23: Power Management

    www.packardbell.com Power management ACPI mode Description Mechanical Off - All devices in the system are turned off completely. No electrical current is running through the system. Except for the real-time clock, power consumption is zero. The machine can be worked on without damaging the hardware or endangering service personnel. G2 (S5) Soft Off - The computer consumes a minimal amount of power.

  • Page 24: Notebook Product Tour

    CHAPTER 1: System specifications Notebook product tour Important Case color may vary from that shown in the pictures. Front View Icon Item Description 5-in-1 card reader Accepts Secure Digital (SD), MultiMediaCard (MMC), Memory Stick (MS), Memory Stick Pro (MS PRO), and xD-Picture Card.

  • Page 25: Left View

    www.packardbell.com Left View Icon Item Description DC-in jack Connects to an AC adapter. HDMI out jack HDMI Plug an HDMI device, such as a high definition television, into (optional) this optional jack. External display Connects to a display device (e.g., external monitor, LCD (VGA) port projector).

  • Page 26: Right View

    CHAPTER 1: System specifications Right View Icon Item Description USB 2.0 ports Connects to USB 2.0 devices (e.g., USB mouse, USB camera). Optical drive Internal optical drive; accepts CDs or DVDs. Optical disk access Lights up when the optical drive is active. indicator Optical drive eject Ejects the optical disk from the drive.

  • Page 27: Top View

    www.packardbell.com Top View Note: The LCD and the keyboard are separate pictures and were joined together for better clarification.
  • Page 28 CHAPTER 1: System specifications Icon Item Description Power button / Turns the computer on and off. / indicator Indicates the computer's power status. Touchpad toggle Turns the internal touchpad on and off. Backup key Launches Acer Backup Management for three-step data backup.

  • Page 29: Bottom View

    www.packardbell.com Bottom View Icon Item Description Subwoofer Emits low frequency sound output. Bottom cover Houses the memory, hard drive, cpu, and wlan card. Battery release latch Releases the batter for removal. Battery bay Houses the computer’s battery pack. Battery lock Locks the battery in position.

  • Page 30: Keyboard

    CHAPTER 1: System specifications Keyboard Your notebook features a full-size keyboard that functions the same as a desktop computer keyboard. Many of the keys have been assigned alternate functions, including shortcut keys for Windows and function keys for specific system operations.

  • Page 31: System Key Combinations

    www.packardbell.com System key combinations When you press the F key and a system key at the same time, your notebook performs the action identified by the text or icon on the key. Press and hold F , then To... press this system key... Turn the capacitive touch key LEDs on or off.

  • Page 32: Touchpad

    CHAPTER 1: System specifications Touchpad Touchpad Left button Right button When you move your finger on the touchpad, the pointer (arrow) on the screen moves in the same direction. You can use the scroll zone to scroll through documents. Use of the scroll zone may vary from program to program. You can use the left and right buttons below the touchpad to select objects.

  • Page 33: Webcam

    www.packardbell.com To... Do this... Start a Position the pointer over the program or object. Press the left button open a file or twice in rapid succession. folder. This action is called double-clicking . Access a Position the pointer over the shortcut menu object.
  • Page 34 CHAPTER 1: System specifications...

  • Page 35: Chapter 2: System Utilities

    CHAPTER2 System utilities • BIOS setup utility • BIOS recovery • Clearing a BIOS password • Unlocking the hard drive...

  • Page 36: Bios Setup Utility

    CHAPTER 2: System utilities BIOS setup utility The BIOS setup utility is a hardware configuration program built into the notebook’s BIOS (Basic Input/Output System). The notebook was shipped already properly configured and optimized. However, if the user encounters configuration problems, you may need to run Setup.

  • Page 37: Navigating The Bios Setup Utility

    www.packardbell.com Navigating the BIOS setup utility Use the keys listed in the legend bar on the bottom of the Setup screen to work your way through the various menu and submenu screens. To use the BIOS setup utility: ← → •...
  • Page 38 CHAPTER 2: System utilities Information The Information menu displays a summary of your computer hardware information. These information are necessary for troubleshooting and may be required when asking for technical support. P h o e n i x S e c u r e C o r e ( t m ) S e t u p U t i l i t y I n f o r m a t i o n M a i n S e c u r i t y...
  • Page 39 www.packardbell.com Parameter Description Manufacturer Name Displays the name of the computer manufacturer. UUID Number Displays the computer’s UUID (universally unique identifier). UUID is an identifier standard used in software construction, standardized by the Open Software Foundation (OSF) as part of the Distributed Computing Environment (DCE). Main Use the Main menu to set the system time and date, and other basic options.
  • Page 40 CHAPTER 2: System utilities Parameter Description Format/Options Quiet Boot Enables or disables the Quiet Boot Disabled function. Enabled When enabled, BIOS setup is in graphical mode and displays only the computer brand logo during POST and while booting. When disabled, BIOS setup is in conventional text mode and displays the system Summary Screen.
  • Page 41 www.packardbell.com Security Use the Security menu option to set system passwords to protect your computer from unauthorized use. P h o e n i x S e c u r e C o r e ( t m ) S e t u p U t i l i t y I n f o r m a t i o n M a i n S e c u r i t y...
  • Page 42 CHAPTER 2: System utilities Parameter Description Option Set HDD Press Enter to set password for accessing the hard disk drive Password (HDD) password. It will be required during boot-up or when waking from hibernation mode. Password on Boot Referred to as the power-on password. When Disabled enabled, the user or supervisor password will be Enabled...
  • Page 43 www.packardbell.com To set a supervisor password: ↑ ↓ Press to highlight Set Supervisor Password , then press Enter The Set Supervisor Password box opens. Enter Type a password, then press Enter Retype the password to verify the first entry, then press You will be prompted to save the new password.
  • Page 44 CHAPTER 2: System utilities Press Enter . A dialog box will appear confirming that changes have been made. Press to save the password and close the Setup Utility or you can proceed to setting a user password. Removing a password To remove a password: ↑...
  • Page 45 www.packardbell.com Boot Use the Boot menu to set the preferred drive sequence in which the Setup utility attempts to boot the operating system. P h o e n i x S e c u r e C o r e ( t m ) S e t u p U t i l i t y I n f o r m a t i o n M a i n S e c u r i t y...
  • Page 46 CHAPTER 2: System utilities Exit The Exit menu screen lists options for quitting from the Setup Utility. P h o e n i x S e c u r e C o r e ( t m ) S e t u p U t i l i t y I n f o r m a t i o n M a i n S e c u r i t y...

  • Page 47: Bios Recovery

    www.packardbell.com BIOS recovery An interruption during a BIOS flash procedure (e.g. a power outage) can corrupt the BIOS code, which will cause the system to go into an unbootable state. You need to access and execute the boot block program to reboot the computer and recover the regular BIOS code.

  • Page 48: Running The Flash Utility

    CHAPTER 2: System utilities Running the Flash utility: To run the Flash utility: Rename the BIOS file as “XXXXXXX.FD”. Copy the “XXXXXXX.FD” file to a bootable USB device containing the Crisis Recovery disk files. Turn off the computer. Insert the USB device containing the renamed BIOS file and the Crisis Recovery disk files to any USB port.

  • Page 49: Clearing A Bios Password

    www.packardbell.com Clearing a BIOS password To clear a lost BIOS password (user or supervisor password) you need to short the clear password hardware gap G35 located near the LCD connector on the system board. Default setting Function Open (normal) Short to clear the user and supervisor passwords.
  • Page 50 CHAPTER 2: System utilities To clear a BIOS password: Turn off the notebook and unplug all the peripherals connected to it. Complete the steps in “Removing the battery” on page Complete the steps in “Removing the bay cover” on page Use an electrical conductivity tool to short the two contacts on the hardware gap together.

  • Page 51: Unlocking The Hard Drive

    www.packardbell.com Unlocking the hard drive To regain access to your computer if you lose the HDD password, you need to generate a master password and unlock the hard drive. To unlock a hard drive: Open the computer in a DOS environment. Type the following command: A\>...
  • Page 52 CHAPTER 2: System utilities...

  • Page 53: Chapter 3: Replacing Notebook Components

    CHAPTER3 Replacing notebook components • Preventing static electricity • Replacing the touchpad board discharge • Replacing the touchpad button • Preparing the work space board • Required tools • Replacing the USB board • Preparing the notebook • Replacing the Bluetooth module •...

  • Page 54: Preventing Static Electricity Discharge

    CHAPTER 3: Replacing notebook components Preventing static electricity discharge Warning To avoid exposure to dangerous electrical voltages and moving parts, turn off your notebook, remove the battery, and unplug the power cord and network cable before opening the case. Warning To prevent risk of electric shock, do not insert any object into the vent holes of the notebook.

  • Page 55: Preparing The Work Space

    www.packardbell.com Preparing the work space Before performing maintenance on the notebook, make sure that your work space and the notebook are correctly prepared. • Wear a grounding (ESD) wrist strap, and use a grounded or dissipative work mat. • Use a sturdy table. Make sure that the table top is wide enough to hold each component as you remove it.

  • Page 56: Required Tools

    CHAPTER 3: Replacing notebook components Required tools To disassemble the notebook, you need the following tools: • Wrist grounding strap (for ESD prevention) • Conductive mat (for ESD prevention) • Flat screwdriver • Phillips screwdriver • Non-marring plastic scribe...

  • Page 57: Preparing The Notebook

    www.packardbell.com Preparing the notebook To prepare the notebook for maintenance: Make sure that the optical disc drive is empty. Turn off the notebook. Close the LCD panel. Disconnect the AC adapter. Disconnect the network cable and all peripheral devices connected to the notebook.
  • Page 58 CHAPTER 3: Replacing notebook components Pull the express card out of its slot. Make sure there is no memory card on the card reader slot. To remove a memory card: Push against the card, as if you were pushing it further into the slot, letting the card spring out...
  • Page 59 www.packardbell.com Pull the memory card out of its slot.

  • Page 60: Removing The Battery

    CHAPTER 3: Replacing notebook components Removing the battery To remove the battery: Turn the notebook over so the base is facing up. Slide the battery lock to the unlocked position (1); slide the battery latch (2), then remove the battery out of the notebook (3). Note The battery has been highlighted with a yellow circle in the above image.

  • Page 61: Removing The Bay Cover

    www.packardbell.com Removing the bay cover To remove or replace components located on the lower bay, you need to remove the bay cover first. Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver To remove the bay cover: Complete the steps in “Preparing the notebook”...
  • Page 62 CHAPTER 3: Replacing notebook components Insert a non-marring plastic scribe on the cover’s notch to release the cover from the computer, and then remove the cover.

  • Page 63: Adding Or Replacing Memory Modules

    Adding or replacing memory modules Important Use only memory modules designed for this Packard Bell notebook. Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver To add or replace memory modules: Complete the steps in “Preparing the notebook”...

  • Page 64: Replacing The Wireless Card

    CHAPTER 3: Replacing notebook components Replacing the wireless card Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (wireless card) To replace the wireless card: Complete the steps in “Preparing the notebook”...
  • Page 65 www.packardbell.com Unplug the antenna cables. Note which color cable corresponds to each of the connectors. Important The number of antenna cables varies depending on the type of wireless card installed on the notebook. IEEE 802.11n cards typically have two antenna cables. Other types of wireless cards usually have only three antenna cables.
  • Page 66 CHAPTER 3: Replacing notebook components Pull the card out of the slot. Insert the new wireless card at a 30° angle into the empty Mini Card slot. The card is keyed so it can only be inserted in one direction. If the card does not fit, make sure that the notch in the card lines up with the tab in the card slot.

  • Page 67: Replacing The Hard Drive 1

    www.packardbell.com Replacing the hard drive 1 Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (hard drive 1) • 4 chrome M3×3 (hard drive bracket) To replace the hard drive: Complete the steps in “Preparing the notebook”...
  • Page 68 CHAPTER 3: Replacing notebook components Grasp the black mylar tab and use it to disengage the hard drive from its connector, and then remove the drive from its bay. If your new hard drive already includes the hard drive bracket, go to step If you need to use the bracket from the old hard drive, go to step...
  • Page 69 www.packardbell.com Remove the hard drive from the bracket. Place the bracket on the new drive and secure it with the screws removed step Slide the new hard drive into the hard drive bay and make sure it’s properly engaged to the connector. Secure the new drive to the system board with the screw removed in step Replace the bay cover, then tighten the cover screws.

  • Page 70: Replacing The Hard Drive 2

    CHAPTER 3: Replacing notebook components Replacing the hard drive 2 Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (hard drive 2) •...
  • Page 71 www.packardbell.com Remove the hard drive screw. Grasp the black mylar tab and use it to disengage the hard drive from its connector, and then remove the drive from its bay. If your new hard drive already includes the hard drive bracket, go to step If you need to use the bracket from the old hard drive, go to step...
  • Page 72 CHAPTER 3: Replacing notebook components Remove the screws that secure the hard drive bracket. Remove the hard drive from the bracket. Place the bracket on the new drive and secure it with the screws removed step Slide the new hard drive into the hard drive bay and make sure it’s properly engaged to the connector.

  • Page 73: Replacing The Optical Drive

    www.packardbell.com Replacing the optical drive Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (optical drive) • 1 chrome M2×4 (optical drive bracket) To replace the optical drive: Complete the steps in “Preparing the notebook”...
  • Page 74 CHAPTER 3: Replacing notebook components Use the non-marring plastic scribe to carefully push the optical drive out of the drive bay, and then slide the drive out. If your new optical drive already has it’s own bracket and bezel, go to step If you need to use the bracket and bezel from the old optical drive, perform steps...
  • Page 75 www.packardbell.com Detach the bracket from the drive. Attach the bezel to the new optical drive. Attach the bracket to the new optical drive and secure it with the screw removed in step Slide the new optical drive into the drive bay and make sure it’s properly engaged to the ODD1 connector.

  • Page 76: Replacing The Thermal Module

    CHAPTER 3: Replacing notebook components Replacing the thermal module Note: The thermal module in this sample is for the discrete model. For the UMA model, the thermal module have four captive screws. Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver...
  • Page 77 www.packardbell.com Loosen the spring-loaded captive screws securing thermal module. Follow the screw sequence indicated on the below images. Remove the thermal module from the system board.
  • Page 78 CHAPTER 3: Replacing notebook components Lay the thermal module down in an upright position to avoid tainting your work space with thermal grease. Remove the barcode sticker on top of the processor. Moisten a soft cloth with isopropyl alcohol and clean the processor die to remove any thermal grease residue.

  • Page 79: Replacing The Cpu

    www.packardbell.com Replacing the CPU Tools you need to complete this task: Flat-blade driver Scribe or non-marring tool Phillips #0 screwdriver To replace the CPU: Complete the steps in “Preparing the notebook” on page Complete the steps in “Removing the bay cover” on page Remove the thermal module by following the instructions in “Replacing the thermal module”...
  • Page 80 CHAPTER 3: Replacing notebook components Remove the old processor from the system board. Install the new processor onto the system board making sure that Pin 1 on the processor (indicated by the silk-screened arrow on the corner of the processor) aligns with Pin 1 on the processor socket (indicated by the absence of a pin hole in the processor socket), then use a flat-blade screwdriver to turn the processor lock screw 1/4-turn clockwise.

  • Page 81: Replacing The Vga Board (For Discrete Models)

    www.packardbell.com Replacing the VGA board (for discrete models) Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2×4 (VGA board) To replace the VGA board (for discrete models): Complete the steps in “Preparing the notebook”...
  • Page 82 CHAPTER 3: Replacing notebook components Remove the VGA board. Note Circuit boards >10 cm has been highlighted with a yellow rectangle as above image shows. Please detach the board and follow local regulations for disposal. Install the VGA board, then replace the screws removed in step Remove any thermal grease residue from the cooling assembly using a soft cloth and isopropyl alcohol.

  • Page 83: Replacing The Keyboard

    www.packardbell.com Replacing the keyboard Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool To replace the keyboard: Complete the steps in “Preparing the notebook” on page Complete the steps in “Removing the battery” on page Turn the notebook over and open the LCD panel to its fully extended position.
  • Page 84 CHAPTER 3: Replacing notebook components Disconnect the keyboard cable and remove the old keyboard. Connect the cable from the new keyboard into the connector. Insert the tabs on the front edge of the keyboard into the slots under the palm rest. You may need to press down on the keyboard keys along the front and side edges of the keyboard to seat the retaining tabs into their corresponding slots.

  • Page 85: Replacing The Keyboard Cover

    www.packardbell.com Replacing the keyboard cover Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool To replace the keyboard cover: Complete the steps in “Preparing the notebook” on page Complete the steps in “Removing the battery” on page Remove the keyboard by following the steps in “Replacing the keyboard”...
  • Page 86 CHAPTER 3: Replacing notebook components The left and right media boards are glued to the keyboard cover. Use the plastic scribe to carefully pry loose the middle cover from the latches securing it. Then remove it from the system. Replace the new keyboard cover and carefully push down on all the side until the latches clicks and secure it in place.

  • Page 87: Replacing The Power Button Board

    www.packardbell.com Replacing the power button board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (power button board) To replace the power button board: Complete the steps in “Preparing the notebook”...
  • Page 88 CHAPTER 3: Replacing notebook components Carefully remove the power button board and turn in over to access the cable. Disconnect the cable from the power button board and remove it from the system. Reconnect the cable to the new power button board and replace it back to the system.

  • Page 89: Replacing The Lcd Panel Assembly

    www.packardbell.com Replacing the LCD panel assembly Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) To replace the LCD panel assembly: Complete the steps in...
  • Page 90 CHAPTER 3: Replacing notebook components Remove the tape securing the LCD and microphone cables. Disconnect the LCD and microphone cables from their system board connectors. If the notebook has a wireless card installed, note the antenna cable routing for later reference and then release the antenna cables from the palm rest. If there’s no wireless card installed, proceed to step...
  • Page 91 www.packardbell.com Pull the antenna cables from underneath the computer and release them from the latches. Remove the top hinge screws securing the LCD assembly. Lift the LCD panel assembly up and away from the notebook.
  • Page 92 CHAPTER 3: Replacing notebook components Position the new LCD panel assembly on the notebook, and then secure it with the hinge screws removed in step If the notebook has a wireless card installed, proceed to step 17 to arrange the antenna cables. If there’s no wireless card installed, proceed to step 18 Refer to the antenna cable routing note made on...

  • Page 93: Replacing The Palm Rest

    www.packardbell.com Replacing the palm rest Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 94 CHAPTER 3: Replacing notebook components Remove the 3 screws securing the palm rest to the base side. Disconnect the DC-in cable from the system and release the cable from the latches. Disconnect the left speaker cable from REAR2 connector and release it from the latch.
  • Page 95 www.packardbell.com Disconnect the touchpad board and touchpad button board cables from TP335 and FP2 connectors. Carefully pry loose the palm rest from the system and lift the palm rest from the system. Place the new palm rest assembly on top of the base enclosure and press it down on all sides until it snaps into place.

  • Page 96: Replacing The Touchpad Board

    CHAPTER 3: Replacing notebook components Replacing the touchpad board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...
  • Page 97 www.packardbell.com Remove the touchpad board cable from the palm rest. Note the orientation of the touchpad board for later reference in installing the new touchpad board.
  • Page 98 CHAPTER 3: Replacing notebook components Insert a small flat-blade screwdriver or non-marring scribe between the touchpad board and the palm rest’s underside, and carefully pry the board loose. Remove the touchpad board from the palm rest. Note A circuit board that is >10 cm has been highlighted with a yellow rectangle as shown in the above image.
  • Page 99 www.packardbell.com Reinstall the keyboard by following the instructions in “Replacing the keyboard” on page If you have disconnected any wireless antennas, reconnect them now. Replace the bay cover, then tighten the cover screws. Reinstall the battery.

  • Page 100: Replacing The Touchpad Button Board

    CHAPTER 3: Replacing notebook components Replacing the touchpad button board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...
  • Page 101 www.packardbell.com Disconnect the cable from the touchpad button board connector. Remove the touchpad button board from the palm rest. Replace the new touchpad button board on the palm rest. Connect the cable to the touchpad button board connector. Replace the screws that was remove in step Reinstall the palm rest by following the instructions in “Replacing the palm...

  • Page 102: Replacing The Usb Board

    CHAPTER 3: Replacing notebook components Replacing the USB board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...
  • Page 103 www.packardbell.com Disconnect the USB board cable from the USBCN1 on the system board and release the cable from the latch. Remove the USB board screw. Release from latch and remove the USB board from the base enclosure.
  • Page 104 CHAPTER 3: Replacing notebook components Place the new USB board in the base enclosure; fix it to the latch and secure it with the screw removed in step Connect the USB board cable to the new USBCN1 on the system board. Reinstall the palm rest by following the instructions in “Replacing the palm rest”...

  • Page 105: Replacing The Bluetooth Module

    www.packardbell.com Replacing the Bluetooth module Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 106 CHAPTER 3: Replacing notebook components The Bluetooth module is glued to the system board. Carefully pry loose the Bluetooth module from the system board using a flat blade screw driver or a plastic scribe. Secure the new Bluetooth module on the system board and connect the Bluetooth cable to it.

  • Page 107: Replacing The Modem Board

    www.packardbell.com Replacing the modem board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 108 CHAPTER 3: Replacing notebook components Carefully lift up the modem board to remove it from the port on the system board; then turn it over to access the cable. Disconnect the cable from the modem board. Connect the cable to the new modem board and connect it to the port on the system board.

  • Page 109: Replacing The Coin-Cell Battery

    www.packardbell.com Replacing the coin-cell battery Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 110 CHAPTER 3: Replacing notebook components Note The battery has been highlighted with a yellow circle in the above image. Detach the battery and follow local regulations for disposing Gently push down the new coin-cell battery to latch it into the system board. Reinstall the palm rest by following the instructions in “Replacing the palm rest”...

  • Page 111: Replacing The Dc-In Cable

    www.packardbell.com Replacing the dc-in cable Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 112 CHAPTER 3: Replacing notebook components Reinstall the palm rest by following the instructions in “Replacing the palm rest” on page Reinstall the LCD panel assembly by following the instructions in “Replacing the LCD panel assembly” on page Reinstall the keyboard cover by following the instructions in “Replacing the keyboard cover”...

  • Page 113: Replacing The System Board

    www.packardbell.com Replacing the system board Tools you need to complete this task: Phillips #0 screwdriver Flat screwdriver Non-marring plastic scribe Screws removed during this task: • 1 chrome M2×4 (wireless card) • 1 chrome M2×4 (hard drive 1) • 1 chrome M2×4 (hard drive 2) •...
  • Page 114 CHAPTER 3: Replacing notebook components Remove the CPU by following the instructions in “Replacing the CPU” on page If the system comes with a VGA board, remove the VGA board by following the instructions in “Replacing the VGA board (for discrete models)” on page Remove the keyboard by following the instructions in “Replacing the...
  • Page 115 www.packardbell.com Remove the one screw securing the system board to the base panel. Carefully lift the right side of the system board and slide it out of the base panel. Note A circuit board that is >10 cm has been highlighted with a yellow rectangle as shown in the above image.
  • Page 116 CHAPTER 3: Replacing notebook components Reconnect the USB board cable by following the instructions in “Replacing the USB board” on page Replace the palm rest by following the instructions in “Replacing the palm rest” on page Replace the LCD panel assembly by following the instructions in “Replacing the LCD panel assembly”...

  • Page 117: Replacing The Left And Right Speakers

    www.packardbell.com Replacing the left and right speakers Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (wireless card) • 1 chrome M2×4 (hard drive 1) •...
  • Page 118 CHAPTER 3: Replacing notebook components Remove the any adhesive tapes securing the speaker cables. Remove the 3 screws securing the left and right speaker to the base panel. Replace the new left and right speakers to the base panel. Secure the left and right speaker with the 3 screws that was remove in step...
  • Page 119 www.packardbell.com Replace the system board by following steps “Replacing the system board” on page 107. Replace the bay cover, then tighten the cover screws. Reinstall the battery.

  • Page 120: Replacing The Subwoofer

    CHAPTER 3: Replacing notebook components Replacing the subwoofer Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 1 chrome M2×4 (wireless card) • 1 chrome M2×4 (hard drive 1) •...
  • Page 121 www.packardbell.com Remove the 2 screws securing the subwoofer to the base panel. Lift to remove the subwoofer from the base panel. Replace the new subwoofer on the base panel. Secure the new subwoofer with the 2 screws that was remove on step Replace the system board by following steps “Replacing the...

  • Page 122: Replacing The Lcd Front Panel

    CHAPTER 3: Replacing notebook components Replacing the LCD front panel Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...
  • Page 123 www.packardbell.com Note: The LCD front panel is glued to the LCD panel by a double-sided adhesive tape. When replacing back the LCD front panel, don’t forget to replace the double-sided adhesive tape that might be destroyed while removing the it. Turn over the LCD front panel as shown.
  • Page 124 CHAPTER 3: Replacing notebook components Reinstall the battery.

  • Page 125: Replacing The Inverter Board

    www.packardbell.com Replacing the inverter board Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 126 CHAPTER 3: Replacing notebook components Turn over the inverter board to access the cables. Disconnect the cables from the inverter board. Connect the cables that was remove in step 9 to the new inverter board. Turn over the inverter board and secure it to the LCD panel lid with the screw that was remove in step Replace the LCD front panel by following the instructions in...

  • Page 127: Replacing The Lcd

    www.packardbell.com Replacing the LCD Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) • 2 black M2.5×8 (LCD panel hinges - top) •...
  • Page 128 CHAPTER 3: Replacing notebook components Disconnect the cable from the webcam. Remove the 8 screws from the left and right hinges on the LCD. Remove the adhesive tape near the webcam area.
  • Page 129 www.packardbell.com Remove the LCD from the LCD assembly lid. Remove the 6 screws from the left and right LCD panel hinge brackets to remove it. Lay the LCD on its front to access the LCD cable.
  • Page 130 CHAPTER 3: Replacing notebook components Detach the portion of the LCD cable that is glued to the LCD panel. Detach the adhesive tape near the LCD cable connector. Disconnect the LCD cable from the connector.
  • Page 131 www.packardbell.com Connect the LCD cable to the connector on the new LCD panel and replace the tapes that might be destroyed when removing the LCD cable. Turn the LCD on its back and secure the left and right LCD bracket with that screws that were removed in step Place the new LCD on the LCD assembly lid and replace the tape remove...

  • Page 132: Replacing The Lcd Panel Hinge Brackets

    CHAPTER 3: Replacing notebook components Replacing the LCD panel hinge brackets Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...
  • Page 133 www.packardbell.com Replace the inverter board by following the instructions in “Replacing the inverter board” on page 119. Replace the LCD front panel by following the instructions in “Replacing the LCD front panel” on page 116. Reinstall the LCD panel assembly by following the instructions in “Replacing the LCD panel assembly”...

  • Page 134: Replacing The Microphone

    CHAPTER 3: Replacing notebook components Replacing the microphone Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...
  • Page 135 www.packardbell.com Replace the new microphone into the LCD front panel. Replace the LCD front panel by following the instructions in “Replacing the LCD front panel” on page 116. Reinstall the LCD panel assembly by following the instructions in “Replacing the LCD panel assembly” on page Reinstall the keyboard cover by following the instructions in “Replacing the keyboard cover”...

  • Page 136: Replacing The Webcam

    CHAPTER 3: Replacing notebook components Replacing the webcam Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...

  • Page 137: Reinstall The Keyboard Cover By Following The Instructions In Keyboard Cover" Procedure

    www.packardbell.com Reconnect the cable to the webcam. Replace the LCD front panel by following the instructions in “Replacing the LCD front panel” on page 116. Reinstall the LCD panel assembly by following the instructions in “Replacing the LCD panel assembly” on page Reinstall the keyboard cover by following the instructions in “Replacing the keyboard cover”...

  • Page 138: Replacing The Antennas

    CHAPTER 3: Replacing notebook components Replacing the antennas Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: • 2 black M2.5×8 (LCD panel hinges - bottom) •...

  • Page 139: Reinstall The Keyboard By Following The Instructions In Keyboard" On Page

    www.packardbell.com Release the antenna cables from the aluminium adhesive tapes securing them and then carefully pry loose the left and right antennas. Secure the new antenna on the LCD assembly lid and route their cables underneath the adhesive tabs. Replace the LCD front panel by following the instructions in “Replacing the LCD front panel”...

  • Page 140: Replacing The Lcd Assembly Lid

    CHAPTER 3: Replacing notebook components Replacing the LCD assembly lid Tools you need to complete this task: Phillips #0 screwdriver Flat screwdriver Non-marring plastic scribe Tools you need to complete this task: Flat-blade driver - OR - Scribe or non-marring tool Phillips #0 screwdriver Screws removed during this task: •...
  • Page 141 www.packardbell.com Remove the LCD by following the instructions in step 8 step 12 “Replacing the LCD” on page 121. Place the LCD on the new LCD assembly lid and follow the instruction in “Replacing the LCD” on page 121 to secure the LCD. Replace the LCD front panel by following the instructions in “Replacing the LCD front panel”...
  • Page 142 CHAPTER 3: Replacing notebook components...

  • Page 143: Chapter 4: Troubleshooting

    CHAPTER4 Troubleshooting • Diagnosing problems • System test procedures • Power-On Self-Test (POST) error message • Index of error messages • Phoenix BIOS beep codes • Symptom-to-FRU error messages • Intermittent problems • Undetermined problems...

  • Page 144: Diagnosing Problems

    CHAPTER 4: Troubleshooting Diagnosing problems Use the following procedure as a guide for diagnosing notebook problems. Important The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. Obtain the failing symptoms in as much detail as possible.

  • Page 145: System Test Procedures

    www.packardbell.com System test procedures Testing the optical drive Use the following procedure to isolate a problem in an optical drive controller, driver, or drive. Important Make sure that the CD-ROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.

  • Page 146: Testing The Memory

    CHAPTER 4: Troubleshooting Testing the memory Memory errors can stop your programs, show error messages on the screen, or hang the system. To test the memory: Boot from the diagnostics diskette and start the diagnostics program. Run the Memory Test and see if the test completes successfully. Press F2 in the test items.
  • Page 147 www.packardbell.com • If the voltage is not correct, replace the power adapter. • If the voltage is within the range, do the following: – Replace the system board. – If the problem is not corrected, see “Undetermined problems” on page 157.

  • Page 148: Testing The Touchpad

    CHAPTER 4: Troubleshooting Testing the touchpad If the touchpad doesn’t work, do the following actions one at a time to correct the problem. To test the touchpad: Reconnect the touchpad cables. Replace the touchpad. Replace the system board. Important Do not replace a non-defective FRU. After you use the touchpad, the pointer may drift on the screen for a short time.

  • Page 149: Power-On Self-Test (Post) Error Message

    www.packardbell.com Power-On Self-Test (POST) error message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. Important Perform the FRU replacement or actions in the sequence shown in the FRU/Action column. If the FRU replacement does not solve the problem, put the original part back in the notebook.

  • Page 150: Index Of Error Messages

    CHAPTER 4: Troubleshooting Index of error messages Error codes Error Codes Error Messages Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (The causes are shown before “Equipment Configuration Error”) Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) Real Time Clock Error CMOS Battery Bad CMOS Checksum Error...
  • Page 151 www.packardbell.com Error Messages FRU/Action Sequence System battery is dead - Replace and run Test or replace the CMOS battery, run the BIOS Setup Utility to Setup reconfigure system time, then reboot the system. System CMOS checksum bad - Default Test or replace the CMOS battery, run the BIOS Setup Utility to configuration used reconfigure system time, then reboot the system.

  • Page 152: No-Beep Error Messages

    CHAPTER 4: Troubleshooting Error Messages FRU/Action Sequence Invalid System Configuration Data • Test or replace the BIOS ROM. • Test or replace the system board. I/O device IRQ conflict • Run “Load Setup Defaults” using the BIOS Setup Utility, then reboot the notebook.

  • Page 153: Phoenix Bios Beep Codes

    www.packardbell.com Phoenix BIOS beep codes Code Beeps POST Routine Description Verify Real Mode Disable Non-Maskable Interrupt (NMI) Get CPU type Initialize system hardware Initialize chipset with initial POST values Set IN POST flag Initialize CPU registers Enable CPU cache Initialize caches to initial POST values Initialize I/O component Initialize the local bus IDE Initialize Power Management...
  • Page 154 CHAPTER 4: Troubleshooting Code Beeps POST Routine Description 1-3-4-3 RAM failure on data bits xxxx of low byte of memory bus Enable cache before system BIOS shadow 1-4-1-1 RAM failure on data bits xxxx of high byte of memory bus Test CPU bus-clock frequency Initialize Phoenix Dispatch Manager Warm start shut down...
  • Page 155 www.packardbell.com Code Beeps POST Routine Description Configure advanced cache registers Initialize Multi Processor APIC Enable external and CPU caches Setup System Management Mode (SMM) area Display external L2 cache size Load custom defaults (optional) Display shadow-area message Display possible high address for UMB recovery Display error messages Check for configuration errors Check for keyboard errors...
  • Page 156 CHAPTER 4: Troubleshooting Code Beeps POST Routine Description Install CD ROM for boot Clear huge ES segment register Fixup Multi Processor table Search for option ROMs. One long, two short beeps on checksum failure. Check for SMART drive (optional) Shadow option ROMs Set up Power Management Initialize security engine (optional) Enable hardware interrupts...
  • Page 157 www.packardbell.com Code Beeps POST Routine Description Initialize error logging Initialize error display function Initialize system error handler PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional) Unknown interrupt Initialize the chipset Initialize the bridge Initialize the CPU Initialize the system timer...
  • Page 158 CHAPTER 4: Troubleshooting Code Beeps POST Routine Description Clear Huge Segment Boot to Full DOS...

  • Page 159: Symptom-To-Fru Error Messages

    www.packardbell.com Symptom-to-FRU error messages Symptom / Error Action in Sequence • The LCD backlight doesn't work. • Run “Load Setup Defaults” using the BIOS Setup Utility, then • The LCD is too dark. reboot the notebook. • The LCD brightness cannot be •...

  • Page 160: Memory Card

    CHAPTER 4: Troubleshooting Memory Card Symptom / Error Action in Sequence The notebook cannot detect the memory • Test or replace the system board. card. Memory card reader slot pin is damaged. • Test or replace the system board. Memory Symptom / Error Action in Sequence Memory count (size) appears different...

  • Page 161: Devices

    www.packardbell.com Symptom / Error Action in Sequence The battery fuel gauge in Windows doesn’t • Remove the battery pack and let it cool for two hours. go higher than 90%. • Refresh the battery (use only battery power until the notebook turns off, then charge the battery).

  • Page 162: Intermittent Problems

    CHAPTER 4: Troubleshooting Intermittent problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect. These reasons include: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists.

  • Page 163: Undetermined Problems

    www.packardbell.com Undetermined problems If the diagnostic test may not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Use these procedures to isolate the failing FRU (do not isolate a non-defective FRU).
  • Page 164 CHAPTER 4: Troubleshooting...

  • Page 165: Chapter 5: System Board Layout

    CHAPTER5 System board layout • EasyNote DT85 system board...

  • Page 166: Easynote Dt85 System Board

    CHAPTER 5: System board layout EasyNote DT85 system board Top view Number Descriptions HDMI port VGA port Ethernet LAN port Line-in jack Mic-in jack Headphone-in jack ExpressCard slot Coin-cell battery...

  • Page 167: Bottom View

    www.packardbell.com Bottom view Number Descriptions DIMM slot 1 DIMM slot 2 CPU socket VGA daughter board slot 5-in-1 card reader slot HDD 1 connector Mini-card slot Wireless LAN card slot...
  • Page 168 CHAPTER 5: System board layout...

  • Page 169: Chapter 6: Fru (Field-Replaceable Unit) List

    CHAPTER6 FRU (Field-Replaceable Unit) list • Introduction • Exploded diagram • FRU list...

  • Page 170: Introduction

    CHAPTER 6: FRU (Field-Replaceable Unit) list Introduction This chapter gives you the FRU (field-replaceable-unit) listing in global configurations of this model. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel.

  • Page 171: Exploded Diagram

    www.packardbell.com Exploded diagram Part NO. Description Q'ty REV. Remark 60.4DW08.001 ASSY LCD PANEL IMR 1X1 SJM80 50.4DW08.001 SJM80 LCD Cable SINGLE HT Camera module Inverter module LCD module 23.42274.001 MICROPHONE SJM80 XINGMENG 33.4DW08.001 Hinge L SJM80 LH 33.4DW06.001 Hinge R SJM80 LH 60.4DW10.001 ASSY LCD BEZEL PB SJM80 Keyboard...

  • Page 172: Fru List

    CHAPTER 6: FRU (Field-Replaceable Unit) list FRU list Category Part Name Description Part No. ADAPTER ADAPTER 90W DELTA ADP 90W 19V 3P AP.09001.024 ADP-90SB BBGE BLUE LV4 ADP-90SB BBGE LED LF ADPAPTER 90W 19V 3PIN ADP 90W 19V 3P AP.0900A.005 HIPRO HP-A0904A3 B1LF HP-A0904A3 LV5 LED LF BLUE...
  • Page 173 www.packardbell.com TOUCHPAD SYNAPTICS TOUCHPAD 56.AYP01.001 TM00372-027 SYNAPTICS TM00372-027 MULTI-MEDIA BOARD CAPACITIVE 55.BCR01.002 RIGHT BUTTON NS-SJM80-R V MULTI-MEDIA BOARD LEFT CAPACITIVE 55.BCR01.003 BUTTON NS-SJM80-L V WIRELESS LAN BOARD WLAN KI.SPM01.003 512AN_MMWG SHIRLEY 802.11ABGN PEAK 5100 MM#895361 SHIRLEYPEAK1* WIRELESS LAN BOARD WLAN KI.SPM01.005 512AG_MMWG SHIRLEY 802.11ABG...
  • Page 174 CHAPTER 6: FRU (Field-Replaceable Unit) list INVERTER BOARD 18" INVERTER DL 19.AYP01.002 DARFON VK.22256.101 VK.22256.101 REV.B Rev.B MULTI-MEDIA BOARD C.A. MMB R FFC 50.BCR01.002 CABLE RIGHT SJM80 TR MULTI-MEDIA BOARD C.A. MMB R FFC 50.BCR01.002 CABLE RIGHT SJM80 JH MULTI-MEDIA BOARD C.A.
  • Page 175 www.packardbell.com POWER CORD 3A 250V CODE UK 2.5A 27.01518.541 3PIN UK 250V 3P BK POWER CORD 5A 250V CODE 5A 250V 27.03118.001 3PIN UK BK 3P UK BK POWER CORD 7A 125V CODE JAPAN 7A 27.01518.551 2PIN JAPAN 125V 2P BK POWER CORD 10A 3PIN BK CODE 27.01518.561...
  • Page 176 CHAPTER 6: FRU (Field-Replaceable Unit) list POWER CORD ACA / ACNZ POWER CODE 27.03218.021 ACA / ACNZ ANNIE POWER CORD 7.5A 250V 3P CODE 7.5A 250V 27.03218.051 AUSTRALIA BK 3P AUSTRALIA POWER CODE 7A 125V CODE 7A 125V 27.03518.161 2PIN JAPAN JAPAN 2PIN BK CASE/COVER/BRACKET ASSEMBLY NEW CARD DUMMY CARD...
  • Page 177 www.packardbell.com UPPER CASE BLACK ASSY UCASE 60.BCR01.002 W/TOUCHPAD CABLE & W/O FP SJM80 TOUCH PAD BUTTON BOARD CABLE W/O FINGER PRINT HOLE LOWER CASE W/DC-IN ASSY LCASE 60.BCR01.001 CABLE & MODEM CABLE & W/O TV SJM80 SPEAKER W/O TV HOLE SPEAKER SPEAKER PACK RIGHT &...
  • Page 178 CHAPTER 6: FRU (Field-Replaceable Unit) list DVD-RW SUPER-MULTI ODD NSM8XS 6M.BCR01.001 MODULE 8X SATA SUPER-MULTI DRIVE ODD TOSHIBA ODD SM SATA KU.00801.030 SUPER-MULTI DRIVE 12.7 TL TS-L633B 12.7MM TRAY DL 8X SATA TS-L633B LF W/O BEZEL ODD HLDS SUPER-MULTI ODD SM SATA KU.0080D.040 DRIVE 12.7MM TRAY DL 8X 12.7 TL HLDS...
  • Page 179 www.packardbell.com CPU INTEL CORE2DUAL IC CPU PENRYN KC.74501.DPP P7450 2.13G 3M 1066 TJ P7450 2.13G NOVT CPU INTEL CORE2DUAL IC CPU PENRYN KC.75501.DPP P7550 PGA 2.26G 3M 1066 P7550 2.26G CPU INTEL CORE2DUAL IC CPU PENRYN KC.86R01.DPP P8600 2.4G 3M 1066 25W P8600 2.4G PGA CPU INTEL CORE2DUAL IC CPU PENRYN...
  • Page 180 CHAPTER 6: FRU (Field-Replaceable Unit) list HDD 160GB 5400RPM 2.5" HDD 160GB WD KH.16008.022 SATA WD WD1600BEVT-22 WD1600BEVT-22ZCT0 ZCT0 FW:11.01A11 HDD 2.5" 5400RPM 250GB HDD 250GB KH.25001.016 SEAGATE ST9250315AS SEAGATE WYATT SATA LF ST9250315AS F/W:0001SDM1 HDD 250GB 5400RPM SATA HDD 250GB KH.25004.003 TOSHIBA LIBRA-BS TOSHIBA...
  • Page 181 www.packardbell.com HDD BRACKET ASSY 60 HDD 33.AYP01.002 BRK BB2 HEATSINK CPU HEATSINK DISCRETE ASSY THERMAL 60.BCR01.003 W/FAN FOXCONN PX SJM80 CPU HEATSINK UMA W/FAN ASSY THERMAL 60.BC801.001 FOXCONN SJM80 KEYBOARD KEYBOARD 100KEYS GP7T KB.I170G.094 SJV70/SJV50 INTERNAL17 MP-07F36F0-442 STANDARD BLACK 4H FR 100GP7T FRENCH KEYBOARD 99KEYS GP7T KB.I170G.111...
  • Page 182 CHAPTER 6: FRU (Field-Replaceable Unit) list KEYBOARD 100KEYS GP7T KB.I170G.102 SJV70/SJV50 INTERNAL17 MP-07F36P0-442 STANDARD BLACK 4H PT 100GP7T PORTUGUESE KEYBOARD 100KEYS GP7T KB.I170G.092 SJV70/SJV50 INTERNAL17 MP-07F36DK-442 STANDARD BLACK DANISH 4H DK 100GP7T KEYBOARD 100KEYS GP7T KB.I170G.098 SJV70/SJV50 INTERNAL17 MP-07F36I0-4424 STANDARD BLACK ITALIAN H IT 100GP7T KEYBOARD 100KEYS GP7T KB.I170G.095...
  • Page 183 www.packardbell.com KEYBOARD 100KEYS GP7T KB.I170G.090 SJV70/SJV50 INTERNAL17 MP-07F36CS-442 STANDARD BLACK 4H CZK100GP7T CZECH/SLOVAK KEYBOARD 100KEYS GP7T KB.I170G.088 SJV70/SJV50 INTERNAL17 MP-07F36B0-442 STANDARD BLACK 4H BE 100GP7T BELGIUM KEYBOARD 100KEYS GP7T KB.I170G.089 SJV70/SJV50 INTERNAL17 MP-07F36PA-442 STANDARD BLACK 4H BR 100GP7T BRAZILIAN PORTUGUESE KEYBOARD 100KEYS GP7T KB.I170G.104 SJV70/SJV50 INTERNAL17...
  • Page 184 LCD BRACKET LEFT HINGE L SJM80 33.BCR01.002 W/HINGE LCD COVER 18.4" IMR ASSY LCD PNL 60.BCR01.005 BLACK W/ANTENNA*2 & IMR 1X2 SJM80 PACKARD BELL LOGO PLATE LCD BEZEL W/PACKARD ASSY LCD 60.BCR01.004 BELL LOGO & CAMERA BEZEL PB SJM80 HOLE...
  • Page 185 www.packardbell.com MICROPHONE MICROPHONE 23.BCR01.003 SJM80 XINGMENG MICROPHONE MICROPHONE 23.BCR01.003 SJM80 GOERTEK INVERTER BOARD 18" INVERTER 18" 19.AYP01.001 DARFON VK.21189.A01 VK.21189.A01 LCD/CAMERA CABLE FOR C.A. LCD SINGLE 50.BCR01.004 SINGLE LAMP LAMP SJM80 HT LCD/CAMERA CABLE FOR C.A. LCD SINGLE 50.BCR01.004 SINGLE LAMP LAMP SJM80 HL MAINBOARD/BOARDS MAINBOARD SJM80MV...
  • Page 186 CHAPTER 6: FRU (Field-Replaceable Unit) list SODIMM 1GB DDRIII SODIMM 1G KN.1GB04.003 1066MHZ MICRON MT8JSF12864HY MT8JSF12864HY-1G1D1 -1G1D1 SODIMM 1GB DDRIII SODIMM 1G KN.1GB09.009 1066MHZ ELPIDA EBJ11UE6BAU0- EBJ11UE6BAU0-AE-E LF AE-E 64*16 0.07UM SODIMM 1GB DDRLLL SODIMM 1G KN.1GB09.011 1066MHZ ELPIDA EBJ11UE6BBS0- EBJ11UE6BBS0-AE-F AE-F SODIMM 1GB DDRIII...
  • Page 187 www.packardbell.com SCREW M2.5X4L NI NYLOK SCRW M2.5X4L 86.00H36.534 NI NYLOK SCREW M2*4 WAFER NI SCRW M2*4 86.9A552.4R0 WAFER NI SCREW M2.5*3 WAFER NI SCRW M2.5*3 86.9A553.3R0 WAFER NI...
  • Page 188 CHAPTER 6: FRU (Field-Replaceable Unit) list...

  • Page 189: Appendix A: Model Definition And Configuration

    APPENDIX A Model definition and configuration...
  • Page 190 EasyNote DT85 Common to all model configurations are: • Camera: 0.3M DV • Card reader: 5-in-1 built-in • Adapter: 65W • LCD: 15.6 WXGA LED-backlit Model Country Acer Part No Description VGA Chip VRAM 1 Memory Memory HDD 1(GB) Wireless Bluetooth Battery ENTJ65-424G32M...
  • Page 191 Model Country Acer Part No Description VGA Chip VRAM 1 Memory Memory HDD 1(GB) Wireless Bluetooth Battery ENTJ65-744G50B S2.B610Y.00 ENTJ65-744G50Bn C2DP7450 N10MGE 512M- SO2G SO2G N500GB5.4K NBDCB4 SP1x2M BT 2.0 6CELL2.8 VHB32BWW1 DDR2 BII6 BII6 N10MGE1512Cck8 (64*16 2*2G/500_L/BT/6L2.8/5R /CB_n2_0.3D_GEc_EN1 ENTJ65-744G50M S2.B610Y.00 ENTJ65-744G50Mn C2DP7450...
  • Page 192 Model Country Acer Part No Description VGA Chip VRAM 1 Memory Memory HDD 1(GB) Wireless Bluetooth Battery ENTJ65-643G32M EMEA Portug LX.B760X.00 ENTJ65-643G32Mn C2DT6400 SO2G SO1G N320GB5.4K NSM8XS SP1x2M 6CELL2.2 VHP32BTPT1 UMACck8 BII6 BII6 2G+1G/320/6L/5R/CB_n 2_0.3D_GEc_PT44 EasyNote_TJ65-BT-206 ENTJ65-644G32M EMEA Portug LX.B760X.00 ENTJ65-644G32Mn C2DT6400 SO2G...
  • Page 194 APPENDIX A:...

  • Page 195: Appendix B: Test Compatible Components

    APPENDIX B Test compatible components • Introduction • Microsoft® Windows Vista® Environment Test...

  • Page 196: Introduction

    APPENDIX B: Test compatible components Introduction This notebook’s compatibility is tested and verified by Acer’s internal testing ® department. All of its system functions are tested under Windows Vista ® ® Windows XP Home, Windows XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.

  • Page 197: Microsoft® Windows Vista® Environment Test

    www.packardbell.com Microsoft Windows Vista Environment ® ® Test Item Specification CRT Port Test CRT monitor ViewSonic 19" CRT VCDTS23283-2G Monitor ViewSonic Professional Series G220 21" Monitor Philips 109P 19” Monitor MAG 810FT II 19” Monitor LCD monitor ViewSonic 19" LCD VA1912W Monitor ViewSonic 20"...
  • Page 198 APPENDIX B: Test compatible components Item Specification USB game pad / joystick ALPS USB Game Pad Microsoft SideWinder Plug & Play GamePad Logitech Freedom 2.4GHz cordless Logitech WingMan USB Extreme Digital 3D Joystick Microsoft USB Side Winder Game pad Saitek P2500 Rumble Force Pad Logitech WingMan Formula (warrior) Joystick Logitech Freedom cordless joystick USB Ethernet/wireless LAN...
  • Page 199 www.packardbell.com Item Specification Multimedia Card Test SD/Mini SD/Micro SD card SanDisk Secure Digital Card 256MB A-DATA Secure Digital Card 4GB 150X Kingston SDHC 8GB Class6 Transcend SD 512MB Transcend 150X Ultra Speed SD 4GB Transcend SD HC 4GB A-DATA 150X Turbo SD 4GB A-DATA miniSD 512MB KINGMAX mini SD Adapter+512MB Mini SD Toshiba SDHC 4GB Class4...
  • Page 200 APPENDIX B: Test compatible components...
  • Page 201 APPENDIX C Online support information...

  • Page 202: Online Support Information

    Online Support Information This appendix describes online technical support services available to help you repair your Packard Bell products. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer branch offices and regional business units can access our website.
  • Page 203 Index battery external monitor bay cover using AC adapter Bluetooth module specifications ESD prevention antennas, replace hard drive features application key keyboard cover Fn key arrow keys function keys audio LCD assembly lid LCD front panel controller LCD panel assembly next track LCD panel hinge brackets play/pause button...
  • Page 204 Index intermittent problems screen objects clear description multimedia control keys Internet chat programs remove mylar tape system board replace navigation keys system keys Communication keyboard backlight Bluetooth keys display toggle specifications optical drive location keyboard cover multimedia control replace replace mute specifications keyboard or auxiliary input...
  • Page 205 www.gateway.com play/pause button previous chapter stop button volume mute webcam specifications usage Windows key wired LAN specifications wireless card replace wireless LAN specifications...
  • Page 206 Index...
  • Page 208 MAN SJV-80 SVC GDE R1 06/09...

Table of Contents