Packard Bell dot Disassembly Manual
  1. Manuals
  2. Brands
  3. Packard Bell Manuals
  4. Laptop
  5. DOT S series
  6. Disassembly manual

Packard Bell dot Disassembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Packard Bell
dot
Disassembly Manual

Advertisement

Table of Contents
loading

Related Manuals for Packard Bell dot

Summary of Contents for Packard Bell dot

  • Page 1 Packard Bell Disassembly Manual...

  • Page 2: Table Of Contents

    Microphone ............................. 16 LCD Panel............................17 LCD Brackets and LCD Cable ......................18 Wireless LAN Adapter........................20 Main Board............................21 Speaker Assembly .......................... 22 Hard Disk Drive..........................24 Memory ............................26 Heat Sink ............................27 Notice.............................. 29 Packard Bell dot Disassembly Manual...

  • Page 3: About This Guide

    Packard Bell B.V. reserves the right to make changes to the dot without notice. For More Information For more information about the Packard Bell dot, visit Packard Bell‘s support web site at www.packardbell.com. The support web site also has links to additional Packard Bell documentation and detailed product specifications.

  • Page 4: Hazardous Voltage

    Always return a Non avviare il sistema senza aver prima defective power supply to the dealer. messo a posto il coperchio. Packard Bell dot Disassembly Manual...

  • Page 5: Battery

    4. Slide the battery lock/unlock latch into the unlock position. Fig. 1 Releasing the battery. 5. Slide the battery release latch into the release position and slide the battery out of the unit. Fig. 2 Removing the battery. Packard Bell dot Disassembly Manual...

  • Page 6: Keyboard

    2. Release the keyboard by prying it up along the top side of the keyboard. There are four tabs holding the keyboard in place on the front. Fig. 3 Releasing the keyboard. 3. Tilt the keyboard gently forward and let it rest upside down on the touchpad. Fig. 4 Removing the keyboard. Packard Bell dot Disassembly Manual...

  • Page 7: Top And Base Cover

    2. Remove the four screws located in the battery compartment. Fig. 6 Removing the battery compartment and base cover screws. 3. Remove the other three screws securing the base cover (see Fig. 4. Turn the notebook over so the top is facing up. Packard Bell dot Disassembly Manual...
  • Page 8 5. Disconnect the touchpad flat cable from the header on the main board. Fig. 7 Disconnecting the touchpad cable. 6. Remove the six screws securing the top cover. Fig. 8 Removing the top cover screws. Packard Bell dot Disassembly Manual...
  • Page 9 8. Turn the notebook over so the top is facing up. 9. Pry loose the LED panel. 10. Remove the two screws underneath the LED panel. 11. Pull the top cover to separate it from the base. Fig. 10 Releasing the top cover. Packard Bell dot Disassembly Manual...

  • Page 10: Usb/Led/Power/Card Reader Board

    To remove the USB/LED/power/card reader board, first remove the top cover (see Top and Base Cover on page 6), and then do the following: 1. Remove the three screws securing the USB/LED/power/card reader board. Fig. 12 Location of the USB/LED/power/card reader board screws. Packard Bell dot Disassembly Manual...

  • Page 11: Lcd Assembly

    Fig. 14 Disconnecting the USB/LED/power/card reader board cable. LCD Assembly To remove the LCD assembly, first remove the USB/LED/power/card reader board (see USB/LED/Power/Card Reader Board on page 9) and then perform the following steps: 1. Turn the notebook upside down. Packard Bell dot Disassembly Manual...
  • Page 12 3. Remove the screws that became accessible after removing the footpads (see 15). 4. Turn the notebook over so the top is facing up. 5. Disconnect the LCD cable from the main board. Fig. 16 Disconnecting the LCD cable. Packard Bell dot Disassembly Manual...
  • Page 13 Fig. 17 Disconnecting the antenna cables. Note: The black antenna cable is connected to MAIN, the white antenna cable to AUX. 7. Clear the two antenna cables and remove them from the housing. Fig. 18 Clearing the antenna cables. Packard Bell dot Disassembly Manual...

  • Page 14: Lcd Bezel

    Ensure that all cables are clear of the base before lifting the LCD assembly upward. LCD Bezel To remove the LCD bezel, first remove the LCD assembly (see LCD Assembly on page 10), and then perform the following steps: 1. Remove the six screw covers on the LCD bezel. Packard Bell dot Disassembly Manual...
  • Page 15 2. Remove the screws that became accessible after removing the covers. Fig. 21 Location of the LCD bezel screws. 3. Starting from the inside edges, carefully pry open the LCD bezel; it has been clicked into place. Fig. 22 Releasing the LCD bezel. Packard Bell dot Disassembly Manual...

  • Page 16: Webcam

    To remove the webcam, first remove the LCD bezel (see LCD Bezel on page 13), and then do the following: 1. Disconnect the cable from the header on the webcam module. Fig. 24 Location of the webcam connector. Packard Bell dot Disassembly Manual...

  • Page 17: Microphone

    To remove the microphone, first remove the LCD bezel (see LCD Bezel on page 13), and then do the following: 1. Disconnect the cable from the header on the microphone module. Fig. 26 Location of the microphone connector. Packard Bell dot Disassembly Manual...

  • Page 18: Lcd Panel

    To remove the LCD panel, first remove the microphone (see Microphone on page 16) and then perform the following steps: 1. Remove the five screws securing the LCD module. Fig. 28 Location of the LCD panel screws. Packard Bell dot Disassembly Manual...

  • Page 19: Lcd Brackets And Lcd Cable

    To remove the LCD brackets and the LCD cable, remove the LCD panel (see LCD Panel on page 17) and then perform the following steps: 1. Turn the LCD panel upside down on an even surface. Packard Bell dot Disassembly Manual...
  • Page 20 2. Remove any adhesive tape securing the LCD cable. Fig. 31 Clearing the LCD cable. 3. Carefully disconnect the LCD cable from the header. Fig. 32 Disconnecting the LCD cable. Packard Bell dot Disassembly Manual...

  • Page 21: Wireless Lan Adapter

    Top and Base Cover on page 6) and then perform the following steps: 1. Remove the screw securing the wireless LAN adapter; it will eject upwards. Fig. 34 Location of the wireless LAN adapter screw. Packard Bell dot Disassembly Manual...

  • Page 22: Main Board

    LAN Adapter on page 20), and then perform the following steps: 1. Disconnect the speaker cable from the header on the main board. Fig. 36 Location of the speaker cable header on the main board. Packard Bell dot Disassembly Manual...

  • Page 23: Speaker Assembly

    3. Lift out the main board. Fig. 38 Removing the main board. Speaker Assembly To remove the speaker assembly, first remove the top cover (see Top and Base Cover on page 6), and then perform the following steps: Packard Bell dot Disassembly Manual...
  • Page 24 1. Clear the speaker cables: detach any adhesive tape securing the speaker cables to the main board. Fig. 39 Clearing the speaker cables. 2. Remove the four screws securing the speaker assembly to the top cover. Fig. 40 Location of the speaker assembly screws. Packard Bell dot Disassembly Manual...

  • Page 25: Hard Disk Drive

    To remove the hard disk drive, first remove the main board (see Main Board on page 21) and then perform the following steps: 1. Remove the two screws securing the hard disk drive bracket. Fig. 42 Location of the hard disk drive screws. Packard Bell dot Disassembly Manual...
  • Page 26 3. Remove the four screws (Phillips-head) on the metal bracket holding the hard disk drive. Fig. 44 Location of the hard disk drive bracket screws. Note: Fig. 44 only two screws are visible; the other two are located on the other side of the bracket. Packard Bell dot Disassembly Manual...

  • Page 27: Memory

    To remove the memory installed, first remove the main board (see Main Board on page 21) and then perform the following steps: Release the clip on each side securing the memory module; the module will eject upwards. Fig. 46 Releasing the installed memory module. Packard Bell dot Disassembly Manual...

  • Page 28: Heat Sink

    1. Turn the main board upside down. 2. Disconnect the fan cable from the header on the main board. Fig. 48 Location of the fan cable header on the main board. Packard Bell dot Disassembly Manual...
  • Page 29 3. Remove the three screws securing the heat sink in designated order. Fig. 49 Location of the heat sink screws. 4. Remove the heat sink. Fig. 50 Removing the heat sink. Packard Bell dot Disassembly Manual...

  • Page 30: Notice

    The information in this guide is subject to change without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B.V. B.V.

Table of Contents