NEC NC900C Installation Manual page 85

Error Code
464 SelfTest HMAC Algorithm Integrity Error
465 SelfTest SHA Algorithm Integrity Error
466 SelfTest TLS Integrity Error
467 SelfTest FPGA Configuration Integrity Error
468 SelfTest FPGA CineLink. 2 Decryption Integrity Error
474 Security Tamper
475 Top Side Security Enclosure Open
476 Bottom Side Security Enclosure Open
477 Security Battery Event
478 Software Commanded Zeroization
481 Security Enclosure Not Armed
482 Physical Marriage Tamper
483 Logical Marriage Tamper
484 Marriage NOT Active
486 Service Door Tamper
487 Security Log Error
488 Security Battery Low Warning
489 Security Log Warning
500 IMB Comm Fail
510 IMB:System Error
511 IMB:Self Test Error
519 IMB:Certificate or Key Error
520 IMB:ICP Communications Status
537 IMB:RTC Error
543 IMB:FPGA Temperature out of range
550 IMB:Supply voltage out of range
574 IMB:Security Tamper
577 IMB:Security Battery Event
581 IMB:Security Enclosure Not Armed
582 IMB:Physical Marriage Tamper
583 IMB:Logical Marriage Tamper
584 IMB:Marriage NOT Active
586 IMB:Service Door Tamper
588 IMB:Security Battery Low Warning
700 Slave Comm Fail
701 Slave Status Fail
702 Lamp Lit Change
703 Slave Comm Ack Fail
710 Lamp1 OverTime
711 Lamp2 OverTime
740 SensorFail Inlet
741 SensorFail DMD
750 OverTemp.DMD Precaution
751 OverTemp.Inlet Precaution
752 Down Lamp Power Activated
Error message Description
Enigma is in FIPS error state. (Self test result)
Enigma is in FIPS error state. (Self test result)
Enigma is in FIPS error state. (Self test result)
Enigma is in FIPS error state. (Self test result)
Enigma is in FIPS error state. (Self test result)
Security tamper condition exists in Enigma.
Security tamper condition exists in Enigma.
Security tamper condition exists in Enigma.
Battery tamper condition exists in Enigma.
Destroyed Enigma key by software command.
Enigma security not armed.
Latched physical marriage tamper condition on Enigma
board.
Logical marriage tamper condition exists in Enigma.
Marriage between ICP and Enigma has NOT been
established (active).
Latched service door tamper condition on Enigma board.
Security log is full and no more log entries can be created
in Enigma. It is the server's responsibility to avoid the
issue.
Close to "(477) Security Battery Event".
Security log is almost full in Enigma.
Close to "(487) Security Log Error".
No communication with the IMB.
IMB Status error
IMB Status error
IMB Status error
IMB fails to do logical marriage to ICP when IMB powers
up. Because of no communications with ICP during logical
marriage.
IMB RTC is "invalid".
IMB Status error
IMB Status error
Security tamper condition exists in IMB.
Battery tamper condition exists in IMB.
IMB security not armed.
Latched physical marriage tamper condition on IMB.
Logical marriage tamper condition exists in IMB.
Marriage between ICP and IMB has NOT been
established (active).
Latched service door tamper condition on IMB
Close to "(577) IMB: Security Battery Event".
Failed to communicate with slave MCU.
Slave MCU is in unexpected status.
Lamp lit status becomes with unexpected state.
(It could appear while dual lamp mode.)
Slave fails to execute the command.
Lamp1 cumulative time is over.
Lamp2 cumulative time is over.
Failed to read inlet sensor.
Failed to read DMD sensor.
Set inside temperature (DMD) is close to over
temperature.
Set inside temperature (Inlet) is close to over temperature.
Down lamp power to decrease set inside temperature.
Appendix
85