Important Information - NEC NC900C Installation Manual

Important Information

Precautions: Please read this manual carefully before using
your NC900C-A and keep the manual handy for future
reference.
The NC900C-A (projector unit) is called the "projector", and
the NC-90MS01 (integrated media server) is called the
"media block" or "IMB" in this manual.
• DLP, DLP Cinema and their respective logos are trade-
marks or registered trademarks of Texas Instruments.
• CineLink is a trademark of Texas Instruments.
• Other product names and manufacturer names described
in this manual are the registered trademarks or trademarks
of their respective companies.
• The display screens and illustrations shown in this manual
may differ slightly from the actual ones.
• GPL/LGPL Software Licenses
The product includes software licensed under GNU Gen-
eral Public License (GPL), GNU Lesser General Public
License (LGPL), and others.
For more information on each software, see "readme.pdf"
inside the "about GPL&LGPL" folder on the supplied
CD-ROM.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
OPEN COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING
PERSONNEL.
This symbol warns the user that uninsulated volt-
age within the unit may have sufficient magni-
tude to cause electric shock. Therefore, it is dan-
gerous to make any kind of contact with any part
inside of this unit.
This symbol alerts the user that important litera-
ture concerning the operation and maintenance
of this unit has been included. Therefore, it
should be read carefully in order to avoid any
problems.
DOC compliance Notice
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in
accordance with EN ISO 7779.
TO QUALIFIED SERVICE
WARNING:
This is a Class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
CAUTION:
• In order to reduce any interference with radio and tele-
vision reception use a signal cable with ferrite core
attached. Use of signal cables without a ferrite core
attached may cause interference with radio and televi-
sion reception.
• This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the installation manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
Important Safeguards
These safety instructions are to ensure the long life of your
projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
1. Consult your dealer for information about transporting
and installing the projector. Do not attempt to transport
and install the projector yourself.
The projector must be installed by qualified technicians
in order to ensure proper operation and reduce the risk
of bodily injury.
2. Place the projector on a flat, level surface in a dry area
away from dust and moisture. Tilting the front of the pro-
jector up or down from level could reduce lamp life.
Do not put the projector on its side when the lamp is on.
Doing so may cause damage to the projector.
3. Do not place the projector in direct sunlight, near heaters
or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam could harm
internal components.
5. Handle your projector carefully. Dropping or jarring your
projector could damage internal components.
6. To carry the projector, a minimum of four persons are
required.
7. Do not hold the lens part with your hand. Otherwise the
projector may tumble or drop, causing personal injury.
3