Switching Zones; Setting The Zone For Which The Sub Remote Control Unit Is Used (Zone Select Lock Mode); Setting The Remote; Resetting The Settings - Denon AVR 4308CI - AV Network Receiver Owner's Manual

Switching Zones

Use this procedure to select the zone to be operated by
the sub remote control unit.
1
[ZONE SELECT]
Press .
The currently selected multi-zone indicator lights.
2
While the multi-zone indicator is light, press
SELECT]
to select the zone to be operated.
The currently selected multi-zone indicator lights.
Setting the Zone for Which the Sub
Remote Control Unit is Used (ZONE
SELECT LOCK Mode)
We recommend always using the sub remote control unit
for the same room. When this is done, the unit can be
set so that the zone does not switch when buttons are
operated.
1
[ADVANCED SETUP]
Use the tip of a pen to press
All the multi-zone indicators light.
2
Select the multi-zone to be set.
The selected multi-zone indicator lights.
q T o set to "MAIN ZONE" : Press [REPEAT].
w T o set to "ZONE2" : Press [RANDOM].
e T o set to "ZONE3" : Press [USB].
r T o set to "ZONE4" : Press [ALL MUSIC/FAVORITES].
3
[ADVANCED SETUP]
Use the tip of a pen to press
The multi-zone indicator turns off.
To Cancel
1
[ADVANCED SETUP]
Use the tip of a pen to press
The currently selected multi-zone indicator lights.
2
[ZONE SELECT].
Press
All the multi-zone indicators light.
3
[ADVANCED SETUP]
Use the tip of a pen to press
The multi-zone indicator turns off.
Setting the Remote ID
When using multiple DENON AV receivers in the same
room, make this setting so that no AV receiver other than
the desired one operates.
1
[MENU]
While pressing
with the tip of a pen.
[ZONE
The multi-zone indicator corresponding to the currently selected
remote ID flashes.
2
Select the remote ID to be set.
q T o set to 1 : Press [REPEAT].
The "M" indicator flashes.
w T o set to 2 : Press [RANDOM].
The "Z2" indicator flashes.
e T o set to 3 : Press [USB].
The "Z3" indicator flashes.
r T o set to 4 : Press [ALL MUSIC/FAVORITES].
The "Z4" indicator flashes.
3
[MENU]
While pressing
.
with the tip of a pen.
The multi-zone indicator turns off.
NOTE
When changing a setting, be sure to set the same remote ID as the
AVR-4308CI's (vpage 38).

Resetting the Settings

[ZONE OFF]
While pressing
.
with the tip of a pen.
All the multi-zone indicators flash 4 times, then all the settings are
restored to their defaults.
.
.
Amp Assign / Multi Zone
Connections and Operations
[ADVANCED SETUP]
, press
The AVR-4308CI is compatible with the following types of playback:
• Multi-zone playback (ZONE2 & ZONE3)
• Bi-amp playback (front speaker)
• Bi-wiring playback (front speaker)
NOTE
• For bi-amp and bi-wiring playback, use speakers compatible with that
type of connection.
• When conducting bi-amp or bi-wiring playback, remove the short-
circuiting boards (or wires) from the speaker terminals.
Multi-Zone Settings with the Amp
Assign Function
[ADVANCED SETUP]
, press
The amp assign function lets you assign the amplifiers for the different
channels built into the AVR-4308CI to the speaker outputs for the
different zones.
Select the desired playback environment from among "Setting
1" to "Setting 6" , then set the corresponding "Amp Assign" mode
at GUI menu "Manual Setup" – "Option Setup" – "Amp Assign"
(vpage 37).
Connect the speakers as described at "Speaker connections" .
With "Setting 4" to "Setting 6" , it is possible to switch the Amp Assign
[ADVANCED SETUP]
, press
mode between the 7 .1-channel mode and the multizone mode without
changing the speaker connections.