Panasonic AJ-HD150 Operating Instructions Manual page 75

Setup menus
USER menu
<AUDIO>
No.
745
746
747
748
749
750
751
752
753
754
755
756
The underline on the setting item denotes the initial setting.
(continued)
Item Setting
Superimposed Superimposed
No.
display display
MONI CH 0000
SEL 0001
0002
0003
0004
MONI AUTO 0000
SEL 0001
0002
MONI SEL 0000
INH 0001
0002
AUDIO PB 0000
VR 0001
ANA CH1 0000
SEL 0001
ANA CH2 0000
SEL 0001
ANA CH3 0000
SEL 0001
ANA CH4 0000
SEL 0001
SD SDI CH1 0000
SEL 0001
SD SDI CH2 0000
SEL 0001
SD SDI CH3 0000
SEL 0001
SD SDI CH4 0000
SEL 0001
– 75 –
MANU This selects the monitor output.
AUTO1
0: The output is as selected in MONITOR SELECT.
AUTO2
1: The cue signal is automatically output in all tape modes
AUTO11
except that PCM AUDIO is output over the –1 to +1 range.
AUTO21 2: The cue signal is automatically output in all tape modes
except in the play mode in which PCM AUDIO is output.
3: The cue input signal is automatically output when the unit is
in the EE mode in addition to AUTO1.
4: The cue input signal is automatically output when the unit is
in the EE mode in addition to AUTO2.
L/R If a setting other than MANU has been selected for setup
L menu item No.745 (MONI CH SEL), the CUE signal is
automatically sent to the monitor output in accordance with
R
the operation mode but this item selects the monitor channel
which will be automatically switched to CUE.
0: The CUE signal is output to both the left and right channels.
1: The CUE signal is output to the left channel only.
2: The CUE signal is output to the right channel only.
This selects whether to enable or disable the MONITOR
OFF
ON SELECT button on the front panel.
ON1 0: The button's operation is enabled.
1: The button's operation is disabled.
2: In the FULL display mode, the button's operation is
disabled; operation is enabled in the FINE display mode
only.
DIS This selects whether the playback level controls are to work in
ENA the EE mode when INT SG has been selected as the setup
menu item No.700 (AUDIO IN SEL) setting.
0: The INT SG output level is fixed at UNITY.
1: The INT SG output level can be varied using the playback
level controls.
CH1
This selects the signals to be output to analog output CH1.
CH5 0: The CH1 signals are output.
1: The CH5 signals are output .
CH2 This selects the signals to be output to analog output CH2.
CH6
0: The CH2 signals are output.
1: The CH6 signals are output .
CH3
This selects the signals to be output to analog output CH3.
CH7
0: The CH3 signals are output.
1: The CH7 signals are output .
CH4 This selects the signals to be output to analog output CH4.
CH8 0: The CH4 signals are output.
1: The CH8 signals are output .
CH1
This selects the signals to be output to SDI output CH1.
CH5
0: The CH1 signals are output.
1: The CH5 signals are output .
CH2
This selects the signals to be output to SDI output CH2.
CH6
0: The CH2 signals are output.
1: The CH6 signals are output .
CH3 This selects the signals to be output to SDI output CH3.
CH7 0: The CH3 signals are output.
1: The CH7 signals are output .
CH4
This selects the signals to be output to SDI output CH4.
CH8
0: The CH4 signals are output.
1: The CH8 signals are output .
Description