Advertisement
Available languages
Available languages
INTRODUCTION
Thank you for purchasing B&W Custom Wall
Mount (CWM™) speakers.
Since its foundation in 1966, the continuing
philosophy of B&W has been the quest for
perfect sound reproduction. Inspired by the
company's founder, the late John Bowers, this
quest has entailed not only high investment in
audio technology and innovation but also an
abiding appreciation of music to ensure that the
technology is put to maximum effect.
It is also our policy to make sure the advanced
features pioneered on one product are incor-
porated into others we manufacture. The
CWM™ range incorporates woven Kevlar
cone mid/bass drive units for lowest coloration
and maximum definition.
However, no matter how good the speakers
themselves, they must work well into the listening
room and time spent on planning the installation
will reap the reward of many hours listening
pleasure. Please read through this manual fully.
It will help you optimise the performance of the
system.
B&W distribute to over 50 countries worldwide
and maintain a network of dedicated distributors
who will be able to help should you have any
problems your dealer cannot resolve.
UNPACKING
(figure 1)
• Fold the top carton flaps right back and invert
the carton and contents.
• Lift the carton clear of the contents.
• Remove the inner packing from the product.
Check the contents:
• 1x Baffle with drive units, crossover and foam
• 1x Wall frame with swing out dogs
• 1x Loudspeaker grille
• 1x Alignment template
• 1x Accessory pack containing:
4x Self-Tapping screws (for frame to PMK
fixing) Not for CWM™500
4x Machine screws (fixing baffles to
wall frames)
We suggest you retain the packaging for future
use. Remove the grille and baffle from the wall
frame and, to avoid damage, keep them in their
plastic bags (and preferably in the carton) away
from the work area until you are ready to fit them.
POSITIONING – NEW
CONSTRUCTION VERSUS RETROFIT
Check that there is no conflict with other in-wall
installations (pipe work, air conditioning, power-
cabling etc.). In existing construction, use a
stud-finding tool to map the wall construction
accurately and a pipe detector to scan the
proposed installation position. Avoid installing
the speakers in the same cavity of the wall as
flimsy ducting, which may be induced to rattle.
The speakers are designed to operate satis-
factorily in a wide range of cavity volumes,
ideally above 15 litres (0.5 cu ft).
The speaker is balanced for half-space mounting
(i.e. flush in a wall or soffit). Placement near
a wall/ceiling, wall/floor junction or in a corner
is to be avoided as it may give rise to too
much bass and a boomy quality to the sound.
If possible, keep the speaker more than 0.5m
(20in) from the wall edges.
The speaker may be mounted in either portrait or
landscape orientation. If portrait orientation is
used, orient the baffle so that the tweeters are
towards the centre of the room.
®
Tilt Axis Control
Generally speakers are balanced to have a flat
frequency response when listening on axis. As
the listening position moves further off this axis
changes in this flat response occur. The Tilt Axis
switch on the front of the baffle is provided to
allow the CWM™Cinema to be listened to off
axis whilst still retaining a flat frequency
response. With the switch set to UP this axis is
angled at roughly 10 degrees upwards (with the
tweeter at the top) from the centre of baffle.
Similarly 10 degrees down with the switch set to
DOWN. Use the Tilt Axis switch to direct the
sound either up or down towards the listening
position (or left or right if the speaker is mounted
in a portrait orientation).
The following sections give guidance on
optimum positioning, but this may be modified in
line with domestic constraints.
Normal Stereo and Home Theatre
Front Left and Right Applications
(figure 2)
The speakers should be positioned with the
tweeters at a little above ear height. If the
speakers are to be used low in the wall invert
the speaker so the bass unit is uppermost. The
spacing between them will depend on the size
of the room and distance to the listeners. As a
general rule they should not be closer to the
listener than 1.5m (5ft) and the distance between
them should not exceed their distance from the
listeners. Having the speakers and listeners
approximately at the corners of an equilateral
triangle is not a bad rule to follow. This
arrangement generally provides the best stereo
imaging. If the speakers are placed too far
apart, a hole-in-the-middle effect may become
apparent. Too close and the panoramic effect
will be lost, accompanied by a reduction in
depth information.
Use the Tilt Axis switch described above for
each speaker to direct the sound either left or
right towards the listening position.
For Home Theatre Installations, the speakers
should not be closer together than the width
of the screen and their height should be
approximately at centre screen height.
Home Theatre Centre Channel
Applications
(figure 3)
Theoretically, the best position for a centre
channel speaker is behind the centre of the
screen, but this can only be realised when using
an acoustically transparent projection screen. In
most cases the speaker will be positioned in a
laterally central position either directly above or
directly below the screen. All other things being
equal, choose the position that is nearest ear
height. Use the Tilt Axis switch described above
to direct the sound either up or down towards
the listening position.
Home Theatre Surround Speaker
Applications
The sound from surround speakers should be as
diffuse as possible. This ensures that the frontal
audio image is not distorted by changes of
listener position or head movements. The
speakers should generally be placed behind
and 0.6m (2ft) or more above ear height.
DAMPING THE WALL CAVITY
A foam pad is supplied to damp the area
behind the drive units. In addition, loosely fill the
whole section of the wall cavity with wadding.
Fibreglass and mineral wool matting supplied for
heat insulation are suitable, but not closed cell
foam or expanded polystyrene. Check that there
is no debris that may fall into the speaker
(especially in ceiling mount situations).
IMPORTANT: YOU SHOULD CHECK THAT THE
MATERIALS YOU USE MEET THE LOCAL FIRE
AND BUILDING REGULATIONS.
FITTING THE WALL FRAME
New Construction
(figure 4)
Fit the separately available pre-mount kit –
(PMK™800) to the studding before the drywall
panels are fitted, following the instructions
supplied with the kit. The drywall panels
should be fitted up to the pre-mount frame
and plastered over.
Screw, but do not tighten, 4 of the screws
provided through the slots in the wall frame into
the pilot holes in the pre-mount frame.
Existing Construction
(figure 5)
Push out the slots in the template provided.
Position the template on the wall as required.
Mark along the inside edges of the slots and cut
out the aperture neatly.
Position the frame in the wall and screw in the 6
screws visible from the front of the frame. These
screws swing out clamping dogs that locate
behind the drywall. Ensure that they have
located properly and loosely tighten the screws.
1
Advertisement
