Alerts; Setting A Proximity Alarm; Calculating The Size Of An Area; Viewing The Almanacs - Garmin fenix Owner's Manual

Alerts

You can set the device to alert you in many different situations
where your awareness of the surrounding conditions or other
data is important. There are three types of alerts: event alerts,
range alerts, and recurring alerts.
Event alert: An event alert notifies you once. The event is a
specific value. For example, you can set the device to alert
you when you reach a specified elevation.
Range alert: A range alert notifies you any time the device is
above or below a specified range of values. For example,
you can set the device to alert you when your heart rate is
below 60 bpm (beats per minute) and over 210 bpm.
Recurring alert: A recurring alert notifies you every time the
device records a specified value or interval. For example,
you can set the device to alert you every 30 minutes.
Alert Name Alert Type
Proximity Recurring
Distance Event,
recurring
Time Event,
recurring
Elevation Event, range,
recurring
Nav. Arrival Event
Pace Range
Heart Rate Range
Cadence Range
Battery Event

Setting a Proximity Alarm

Proximity alarms alert you when you are within a specified
range of a particular location.
1 Select the Orange key.
2
Select Alerts > Proximity > Create New.
3
Select a location.
4
Enter a radius.
5
Select Done.

Calculating the Size of an Area

Before you can calculate the size of an area, you must acquire
satellites (page 2).
1
Select the Orange key.
2
Select GPS Tools > Area Calc..
3
Walk around the perimeter of the area you want to calculate.
4
When you are finished, select the Orange key to calculate
the area.
5 Select an option:
• Select Save Track, enter a name, and select Done.
• Select Change Units to convert the area to a different
unit.
• Select to exit without saving.

Viewing the Almanacs

You can view almanac information for the sun and moon, and
hunting and fishing.
1
Select the Orange key.
ANT+™ Sensors
Description
See page 7.
You can set an interval or a custom
distance from your final destination.
You can set an interval or a custom time
from your estimated time of arrival.
You can set minimum and maximum
elevation values. You can also set the
device to alert you when you ascend or
descend a specified amount.
You can set alerts for reaching waypoints
and the final destination of a track or
route.
You can set minimum and maximum pace
values.
You can set minimum and maximum
heart rate values or select zone changes
(page 8).
You can set minimum and maximum
cadence values.
You can set a low battery power alert.
2
Select an option:
• To view the sunrise, sunset, moonrise, and moonset
information, select GPS Tools > Sun & Moon.
• To view the predicted best times for hunting and fishing,
select GPS Tools > Hunt & Fish.
3
If necessary, select or

Viewing Satellite Information

The satellite page shows your current location, GPS accuracy,
satellite locations, and signal strength.
1
Select the Orange key.
2
Select Start GPS.
3 Select the Orange key.
4
Select GPS Tools > Satellite.
5
Select to view additional information.

Simulating a Location

When you are planning routes or activities in a different area,
you can turn off GPS and simulate a different location.
1
Select the Orange key.
2
Select Setup > System > GPS Mode > Demo Mode.
3
Select a location.
4 Select Go > Move to Location.
ANT+™ Sensors
The device is compatible with these optional, wireless ANT+
accessories.
• Heart rate monitor (page
• GSC™ 10 speed and cadence sensor
• tempe wireless temperature sensor
For information about compatibility and purchasing additional
sensors, go to http://buy.garmin.com.

Pairing Your ANT+ Sensors

Before you can pair, you must put on the heart rate monitor or
install the sensor.
Pairing is the connecting of ANT+ wireless sensors, for
example, connecting a heart rate monitor with your Garmin
device.
1
Bring the device with range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2 Select the Orange key.
3 Select Setup > ANT Sensor.
4
Select your sensor.
5
Select New Search.
When the sensor is paired with your device, the sensor
status changes from Searching to Connected. Sensor data
appears in the data page loop or a custom data field.

tempe

The tempe is a wireless temperature sensor. You can attach the
sensor to a secure strap or loop where it is exposed to ambient
air, and therefore, provides a consistent source of accurate
temperature data. You must pair the tempe with your device
(page 7) to display temperature data from the tempe.

Putting On the Heart Rate Monitor

NOTE: If you do not have a heart rate monitor, you can skip this
task.
to view a different day.
7)
(page 8)
(page 7)
7