Related Manuals for Directed Electronics BOA 165B
Summary of Contents for Directed Electronics BOA 165B
- Page 1 1 1 6 6 5 5 B B O O w w n n e e r r ’ ’ s s / / I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e...
- Page 2 Directed Electronics, Inc. (hereinafter "Directed") promises to the original purchaser to repair or replace with a comparable reconditioned Directed DIY remote start unit if this Directed DIY remote start unit (hereinafter "Unit"), excluding without limitation, any...
- Page 3 This product warranty is automatically void if its date code or serial number is defaced, missing, or altered. This warranty will not be valid unless you have completed the war- ranty card and mailed it to Directed Electronics, Inc. within 10 days after purchase to the address listed on the warranty registration card.
-
Page 4: Table Of Contents
....................4 4 5 5 © 2004 Directed Electronics, Inc. - Page 5 © 2004 Directed Electronics, Inc.
- Page 6 Digital Multi-Meter Drill Drill Bits Screwdrivers (Phillips and Flathead) Wire Stripper Solder Iron Electrical Tape Pliers Crimping Tool note: The installation tools listed above may be optional and those required will vary depending on your vehicle. © 2004 Directed Electronics, Inc.
-
Page 7: System Maintenance
Failure to properly install the remote starter may result in property damage, personal injury, or both. system maintenance The system requires no specific maintenance. -
Page 8: Fcc/Id Notice
3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote control © 2004 Directed Electronics, Inc. - Page 9 Safety Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote © 2004 Directed Electronics, Inc.
- Page 10 P P A A Y Y F F O O R R I I N N S S T T A A L L L L A A T T I I O O N N O O R R R R E E I I N N S S T T A A L L L L A A T T I I O O N N C C O O S S T T S S . . © 2004 Directed Electronics, Inc. O O P P E E R R A A T T I I N N G G...
- Page 11 (-) Remote Start Activation Input Factory Alarm Disarm (+) Output to Starter Circuit (+) (30A) High Current 12V Input (+) Output to ACC1 Circuit (+) Output to IGN1 Circuit (+) (30A) High Current 12V Input Output to IGN2 Circuit © 2004 Directed Electronics, Inc.
- Page 12 LED tester is not being used. 2. Connect the Black clip to a good chassis ground. 3. If a positive voltage source is probed, the Red LED will illuminate brightly. © 2004 Directed Electronics, Inc.
- Page 13 Tampering may cause unintended deployment of airbags. warning! Verify that the vehicle is set to park and that the parking brake is set before beginning installation. © 2004 Directed Electronics, Inc.
-
Page 14: Step
More problems are attributed to poor ground con- nections than any other cause. Take extra care to ensure the ground is a clean metal-to-metal contact and secure. NOTE: © 2004 Directed Electronics, Inc. - Page 15 The color and identity of your specific vehicle wiring can be obtained at www.boasecurity.com. With the key in the OFF position, test the suspect wire. The constant power wire will illu- minate the LED tester. © 2004 Directed Electronics, Inc.
- Page 16 If the LED tester extinguishes this is not an ignition wire but an accessory wire. If the wire tests correctly, solder the PINK (C) relay wire to it and cover the connection with electrical tape. © 2004 Directed Electronics, Inc.
- Page 17 If the wire tests correctly, strip the insu- lation off a small portion and solder the thick ORANGE (C) relay wire to it and wrap it with electrical tape. If your vehicle requires more than one accessory contact BOA Technical Support. © 2004 Directed Electronics, Inc.
- Page 18 ) and try to start the vehicle. If the vehicle does not start, the correct wire has been identified. Reconnect both ends of the starter wire while soldering the thick VIOLET (A) relay wire to it and wrap the connection with electrical tape. © 2004 Directed Electronics, Inc.
- Page 19 BROWN (H1/3) wire on the main harness to it and wrap the connection with electrical tape. important! Do not use the vehicle until you confirm the operation of the brake shutdown. © 2004 Directed Electronics, Inc.
- Page 20 Do not use the vehicle until you confirm the operation of the hood pin shutdown. The bypass toggle switch is designed to bypass the remote start in an emergency or to disable the remote start functions © 2004 Directed Electronics, Inc.
- Page 21 If the web vehicle information suggests a different type of parking light circuit, please contact BOA Technical Support. TO GRAY (H1/5) WIRE CONTROL MODULE BYPASS TOGGLE SWITCH BYPASSED WHEN CLOSED © 2004 Directed Electronics, Inc.
- Page 22 Once you have identified the correct wire, strip a small portion of insulation off this wire and solder the WHITE (H1/8) wire from the main connector to it and wrap the connection with electrical tape. © 2004 Directed Electronics, Inc.
- Page 23 In this case the engine will not be protected from over cranking, over revolution, or under revolution of the engine. If this is the case, it will be necessary to use the tachometer. © 2004 Directed Electronics, Inc.
- Page 24 Run the VIOLET/WHITE (H1/2) wire from the main connector through the firewall into the engine compartment along side the hood pin wire. Use the same procedure as with the © 2004 Directed Electronics, Inc.
- Page 25 Locate the factory alarm disarm wire using the web site vehicle information. Once the suspect wires are located, place the red lead of the LED tester to a (+)12 volt constant source and secure © 2004 Directed Electronics, Inc.
- Page 26 There are several types of immobilizers, with the most common being the resistance based passlock/passlock 2 systems found on most newer GM vehicles. This system can be bypassed using the 555L immobilizer bypass module available at your local retail © 2004 Directed Electronics, Inc.
- Page 27 The system can only learn, after being connected and with the FIRST IGNITION ON. If not learned with the first ignition on the battery will have to be disconnected and then reconnected and the procedure repeated. © 2004 Directed Electronics, Inc.
- Page 28 The accessories and ignition should turn on followed by the starter cranking and the vehicle engine running. Pressing on the remote will shut the engine off. © 2004 Directed Electronics, Inc. button button on the additional trans- twice on the...
-
Page 29: Standard Configuration
Button This button engages timer mode. Press the the engine every 3 hours (12-minute run time). Button This button is used to program the system. button to start © 2004 Directed Electronics, Inc. - Page 30 The system is programmed to attempt two starts using tachometer mode. If after the second start attempt the control module did not see a tachometer input the system will attempt to start a third time using voltage mode. © 2004 Directed Electronics, Inc. button twice.
-
Page 31: Warning! Safety First
(1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety © 2004 Directed Electronics, Inc. - Page 32 This testing should be performed by an authorized Directed Electronics, Inc. dealer in accordance with the Safety Check outlined in the product installation guide.
-
Page 33: Remote Start
While the vehicle is running during remote start operation, the system will monitor the vehicle and will automatically shut down the engine if the system receives any of the following shut- down inputs: The brake pedal is pressed. The hood is opened. © 2004 Directed Electronics, Inc. -
Page 34: Timer Mode
To remote start the vehicle in timer mode: Press the button on the transmitter twice within 3 seconds. The parking lights will flash 4 times to confirm remote start timer operation. © 2004 Directed Electronics, Inc. - Page 35 Use the following procedure to enter Pit Stop Mode: Place the transmission in park and put the parking brake on. Leave the ignition on. button on the transmitter can be button does not affect © 2004 Directed Electronics, Inc.
- Page 36 The system will automatically synchronize and the transmitter will respond normally. © 2004 Directed Electronics, Inc. r r e e - - s s y y n n c c h h r r o o n n i i z z e e ®...
- Page 37 T T h h e e s s t t a a r r t t e e r r c c o o n n t t i i n n u u e e s s t t o o c c r r a a n n k k e e v v e e n n t t h h o o u u g g h h t t h h e e e e n n g g i i n n e e h h a a s s s s t t a a r r t t e e d d . . © 2004 Directed Electronics, Inc.
- Page 38 If there is voltage present, skip to Step 4. If there is no voltage present, advance to Step 2. 2. Check the 30A fuses. 3. Make sure the purple starter wire is connected on the © 2004 Directed Electronics, Inc.
- Page 39 Control Module: under the dash area of the vehicle. It houses the microprocessor that monitors your vehicle and controls all system functions. A hand-held, remote control which operates the Transmitter: various functions of your system. © 2004 Directed Electronics, Inc.
- Page 40 © 2004 Directed Electronics, Inc.
- Page 41 _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ © 2004 Directed Electronics, Inc.
- Page 42 Q Q U U I I C C K K R R E E F F E E R R E E N N C C E E G G U U I I D D E E : : T T o o r r e e m m o o t t e e s s t t a a r r t t u u s s i i n n g g y y o o u u r r r r e e m m o o t t e e Press twice within three seconds.
- Page 43 The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, DIRECTED is ISO 9001 registered.