Table of Contents
Advertisement
Quick Links
865GFT
( for 2-User-System )
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-865GFT3A
Release date: Jan. 2004
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for JETWAY 865GFTR3A
Summary of Contents for JETWAY 865GFTR3A
- Page 1 865GFT ( for 2-User-System ) USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-865GFT3A Release date: Jan. 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE........................... ii MANUAL REVISION INFORMATION .................... ii COOLING SOLUTIONS ........................ii CHAPTER 1 INTRODUCTION OF 865GFT MOTHERBOARD THE WORLD FIRST 2-USER MOTHERBOARD............1 FEATURE OF MOTHERBOARD ..................2 SPECIFICATION........................3 PERFORMANCE LIST ......................4 LAYOUT DIAGRAM & JUMPER SETTING ..............5 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS ................ -
Page 3: User's Notice
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. -
Page 4: Chapter 1 Introduction Of 865Gft Motherboard
Chapter 1 Introduction of 865GFT Motherboard 1-1 The World First 2-User Motherboard Introduction The 865GFT MagicTwin is the world’s first multi-user enabled motherboard solution available in the market. The special designed 2-user-system motherboard allows two users to share the computing power of a single PC system. With integrated circuitry onboard, the ®... -
Page 5: Feature Of Motherboard
1-2 Feature of motherboard The 865GFT motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package/ Northwood Processor with the Intel 865G Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design (Support Hyper Threading CPU) and the memory size expandable to 2.0GB. -
Page 6: Specification
1-3 Specification Spec Description ∗ ATX form factor 6 layers PCB size: 18.5x25.5cm Design ∗ Intel 865G Graphics Memory Controller Hub (GMCH) Chipset ∗ Intel 82801EB I/O Controller Hub (ICH5) Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin CPU Socket (mPGA478B Socket) Grid Array (FC-PGA2) package processor... -
Page 7: Performance List
1-4 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU: Intel Pentium 4 2.53GHz (533MHz FSB)/3GHZ (800MHz FSB) mPGAB package... -
Page 8: Layout Diagram & Jumper Setting
1-5 Layout Diagram & Jumper Setting PRINT PS/2 Mouse LINE-IN PS/2 Keyboard LINE-OUT COM1 USB4 K/B Power ON Jumper (JP4) CPU Socket PS2 KB/Mouse Port ATX Power Connector ATX 12V Power Conn. CPUFAN Serial Port COM2 USB Power ON Jumper (JP6) USB Port (USB2) PC99 Back Panel DIMM Socket X2... - Page 9 Jumpers Jumper Name Description Page CMOS RAM Clear 3-pin Block Keyboard Power On Enable/Disabled 3-pin Block JP5, JP6 USB Power On Enabled/Disabled 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 20-pin Block P.12 ATX12V ATX 12V Power Connector 4-pin Block P.13 KB/MOUSE...
-
Page 10: Chapter 2 Hardware Installation
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. -
Page 11: Install Cpu
(3) CMOS RAM Clear (3-pin): JP1 A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JP1 to store the CMOS data. To clear the CMOS, follow the procedure below: Turn off the system and unplug the AC power Remove ATX power cable from ATX power connector Locate JP1 and short pins 2-3 for a few seconds Return JP1 to its normal setting by shorting pins 1-2... -
Page 12: About Intel Pentium 4 478-Pin Cpu
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software. Processor - the "central processing unit"... -
Page 13: Install Memory
2-4 Install Memory This motherboard provides 184-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. WARNING! Due to Intel 865 chipset specification limitation this motherboard can not support 8Mx16/16Mx16/32Mx16 Double Side memory Module. -
Page 14: Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. 2. Remove your computer’s cover and the bracket plate on the slot you intend to use. 3. Align the card’s connectors and press firmly. 4. -
Page 15: Agp Slot
Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the motherboard due to Intel® 865 chipset can not support AGP 2X (3.3V). The AGP Slot also supports AGP Digital Display Card for digital display and TV-out. IMPORTANT! Before you plug-in AGP card, please make sure the following notice is fully understood and practiced. - Page 16 This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system.
- Page 17 (11) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (12) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable.
-
Page 18: Headers
(13) Serial-ATA Port connector: SATA1/SATA2 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. Pin 1 Pin 1 SATA1 SATA2 Serial-ATA Port Connector 2-6-2 Headers Serial Port COM2 Header (9-pin) : COM2 COM2 Pin 1 Note: Orient the read marking on the... - Page 19 USB2 Pin 1 DATA DATA +DATA +DATA OC (Over Current) USB Port Headers Power Button/ Reset Button/ SPDIF-In (Receiver) Optical Header (7-pin) : JW_FP SPDIF-In The SPDIF-In Optical Receiver Connector, by this connector you can in-put digital signal from other device such like CD-ROM, CD player to get high quality audio. Power switch: POWER BUTTON This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system Reset switch lead: RESET BUTTON...
- Page 20 LAN Activity LED: LAN_LED This connector connects to the LAN activity indicator light on the case LCD Display Panel Header : This connector connects to the LCD Display Panel on the case to show Timer and the PC Health situation such like FAN Speed/ CPU and System Temperature. HD _ LED DVD _ LED LAN _ LED...
- Page 21 C DIN CD Audio-In Headers (12) SPDIF-Out Headers (3-pin) : SPDIF_OUT SPDIF_OUT SPDIF-OUT Headers 2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.
-
Page 22: Starting Up Your Computer
5. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. The system will then run power-on test. -
Page 23: Entering Setup
In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: •... - Page 24 Standard CMOS Features Miscellaneous Control Advanced BIOS Features Load optimized Defaults Advanced Chipset Features Load Standard Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations Save & Exit Setup PC Health Status Exit Without Saving ↑...
-
Page 25: Standard Cmos Features
Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. 3-4 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into several categories. Each category includes no, one or more than one setup items. -
Page 26: Advanced Bios Features
If you select Manual, related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer. If the controller of HDD interface is SCSI, the selection shall be “None”. If the controller of HDD interface is CD-ROM, the selection shall be “None”... - Page 27 CPU Internal Cache The default value is Enabled. Enabled (default) Enable cache Disabled Disable cache Note: The internal cache is built in the processor. External Cache Choose Enabled or Disabled. This option enables the Level 2 cache memory. CPU L2 Cache ECC Checking Choose Enabled or Disabled.
-
Page 28: Advanced Chipset Features
Security Option This category allows you to limit access to the system and Setup, or just to Setup. The system will not boot and access to Setup will be denied if the System correct password is not entered at the prompt. Setup (default) The system will boot, but access to Setup will be denied if the correct password is not entered prompt. -
Page 29: Dram Timing Settings
The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The settings are: Enabled and Disabled. AGP Transfer Mode In this item you can select AGP transfer mode Auto/4X/1X the Default setting is Auto. 3-6-1 DRAM Timing Settings CMOS Setup Utility –... -
Page 30: Onboard Ide Function
↑ ↓ → ← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Onboard IDE Function Please refer to section 3-7-1 Onboard Device Function Please refer to section 3-7-2 Onboard Super IO Function Please refer to section 3-7-3 Init Display First This item allows you to decide to activate whether PCI Slot or AGP VGA first. -
Page 31: Onboard Device Function
master driver). If your hard drive and your system software both support Ultra DMA/33 and Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. -
Page 32: Onboard Super Io Function
CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Onboard Super IO Function Onboard FDC Controller Enabled Item Help Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 UART Mode Select Normal Menu Level >> UR2 Duplex Mode Half Onboard Parallel Port 378/IRQ7 Parallel Mode ECP Mode Use DMA... -
Page 33: Power Management Setup
be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9 spec. can be chosen. 3-8 Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use. -
Page 34: Pm Timer Reload Events
During Disabled, the system will ignore any incoming call from the PCI card/modem. During Enabled, the system will boot up if there’s an incoming call from the PCI card /modem. Wake-Up on RTC Alarm This function is for setting date and time for your computer to boot up. During Disabled, you cannot use this function. -
Page 35: Pnp/Pci Configuration Setup
Resources Controlled By Manual Menu Level > x IRQ Resources Press Enter PCI/VGA Palette Snoop Disabled Assign IRQ For VGA Enabled ↑ ↓ → ← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Reset Configuration Data Normally, you leave this field Disabled. -
Page 36: Pc Health Status
IRQ-5 assigned to PCI Device Menu Level >> IRQ-7 assigned to PCI Device IRQ-9 assigned to PCI Device IRQ-10 assigned to PCI Device IRQ-11 assigned to PCI Device IRQ-12 assigned to PCI Device IRQ-14 assigned to PCI Device IRQ-15 assigned to PCI Device ↑... -
Page 37: Miscellaneous Control
CPU/SYSTEM temperature below Temp1/Temp2. Current CPU Temperature/Current System Temp/Current CPUFAN, SYSFAN Speed/ Vcore/Vdd/3.3V This will show the CPU/FAN/System voltage chart and FAN Speed. 3-11 Miscellaneous Control This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Miscellaneous Control CPU Clock Ratio Item Help... -
Page 38: Load Standard/Optimized Defaults
Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter> on this item, you get a confirmation dialog box with a message similar to: Load Optimized Defaults (Y/N)? N Pressing <Y>... -
Page 39: Magic Install Supports Windows 98Se/Me/Nt4.0/2000/Xp
CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL Supports WINDOWS 98SE/ME/NT4.0/2000/XP Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive). -
Page 40: Inf Install Intel 865/875 Chipset System Driver
1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install Utility appears 3. This license agreement appear , click Yes , 4. Select if you want computer re-started click the readme information appear , click Next Finish NOTE: MAGIC INSTALL will auto detect file path X:\INTEL865\INF\SETUP.EXE This driver supports WINDOWS 98SE/ME/2000/XP... -
Page 41: Sound Install Alc Audio Codec Driver
Click YES, This is Announce CopyRight If You Want Re-start Computer , Click FINISH 4-3 SOUND install ALC AC97 Codec Audio Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click OK, start to install DRIVER 3. -
Page 42: Lan Install Realtek Rtl8110S Gigabit Ethernet Nic Driver
5. Sound Effect select and KaraOK Mode 6. Manual Sound Effect Setting Function Note: The path of the file For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALC\SETUP.EXE Note: In Win2K/WinME users have to click Control Panel\System\Device Manager\ DVD\CD-ROM drives to Enabled digital CD Audio for the CD-ROM Device when use the SPDIF-Out digital signal. -
Page 43: Usb2.0
4-5 USB2.0 install Intel USB2.0 Driver Windows 98SE/ME USB 2.0 Driver installation 1. Click USB2.0 when Magic Install Menu 2. This license agreement appear, click Yes, then appear finish install driver , click Close and restart your computer Windows 2000/XP USB 2.0 Driver installation Windows 2000 Mothed1 Start Windows 2000 OS and Internet Connect, Select "Windows Update", Select Driver Update, Install Windows2000 USB2.0 Driver... -
Page 44: Mbios&Dx9 Install Bios Live Update Utility And Directx9
3. Select Finish after setup complete 4. Execute MY GUARD utility, On-time Monitoring your system health NOTE: MAGIC INSTALL will auto detect file path X:\INTEL865\HEALTH\SETUP.EXE This driver supports WINDOWS 95/98/98SE/NT4.0/2000 4-7 MBIOS&DX9 Install BIOS Live Update Utility and DIRECTX9 1. Click Magic BIOS when Magic Install 2. - Page 45 5. When On-line update BIOS the program will 6. Click Next if you need update BIOS, after auto-check your BIOS version upgrade BIOS, the system will clear CMOS and automatically restart Click Yes if you want to update the BIOS When System programming BIOS don’t turn otherwise choose No to exit off power, after finish update BIOS, the...
-
Page 46: Pc-Cillin Install Pc-Cillin2002 Anti-Virus Program
4-8 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PC- MENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PC- CILLIN 2002" (2) Click Open Manual. you can learn PC- CILLIN 2002 how to use 3. -
Page 47: How To Update Bios
7. After PC-CILLIN 2002 complete, Please 8. finish register process, we recommend select register your information and get LICENSE update item to download newest engine code KEY from TREND MICRO web site, enter and virus code your license key and click FINISH Note : Please install ACROBAT READER, Before you read PC-CILLIN 2002 User Manual, the path at X:\acrobat\ar500eng.exe... -
Page 48: Chapter 5 Installation Of Magictwin
CHAPTER 5 5-1 INSTALLATION OF MagicTwin (a 2-User-System solution) Introduction MagicTwin is a 2-User-System solution built on this special designed motherboard with dual video connectors (such as a dual port AGP VGA card), two PS/2 keyboards and two PS/2 mice connected from motherboard using packaged Y-cables and one piece of software (Driver and Tools). - Page 49 As well attach the delivered Y- cables to the “green” port (former PS/2 Mouse port) and into the “violet” port (former PS/2 Keyboard port) at the rear side of the motherboard. Connect the 1 . and 2 . Mouse to the octopus cable, which is also linked to the “green”...
- Page 50 Welcome- Mask, click “Next” Option: Change destination path or click “Next” Password and Network Console, click “Next” Type in the Serial and your Address, click “Next” Installation in process, please wait… Afterwards “Reboot your PC”. Windows is restarting and loading the new installed drivers. The MagicTwin will be activated and assign automatically the 2 Station to the 2 monitor, -PS/2-keyboard and PS/2 mouse.
- Page 51 NVIDIA AGP-card The NVIDIA AGP dual-headed adapters are supported under MagicTwin. It does not work with ATI graphic card at the moment. One display can be used by the host and the second by the MagicTwin station. This will be done automatically after installation of MagicTwin. Please refer to the MagicTwin XP 2-User Software Installation Guide for detail.