Table of Contents
Advertisement
MULTI-FORMAT MONITOR
DT-V1700CG
For Customer Use:
Enter below the Serial No. which is located on the rear of
the cabinet. Retain this information for future reference.
:
Model No.
:
Serial No.
Untitled-1
DT-V1700CG
1
INSTRUCTIONS
UNDER
PULSE
DEGAUSS
SCAN
CROSS
MENU
BLUE
ASPECT
VOLUME
CHECK
The illustration above shows the DT-V1700CG with provided
wide mask attached.
01.3.27, 9:58
COLOR
OFF
POWER
SLOT 1
SLOT 2
SLOT 3
A
B
C
D
E
F
AREA
INPUT SELECT
MARKER
Advertisement
Table of Contents
Related Manuals for JVC DT-V1700CG - High-definition Dtv Monitor
Summary of Contents for JVC DT-V1700CG - High-definition Dtv Monitor
- Page 1 MULTI-FORMAT MONITOR DT-V1700CG INSTRUCTIONS For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. UNDER PULSE COLOR DEGAUSS SCAN CROSS POWER SLOT 1 SLOT 2 SLOT 3 Model No.
-
Page 2: Safety Precautions
Thank you for purchasing this JVC multi-format monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. SAFETY PRECAUTIONS FCC INFORMATION WARNING : CAUTION: Changes or modification not approved by TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT JVC could void the user’s authority to operate... -
Page 3: Table Of Contents
CONTENTS SAFETY PRECAUTIONS ................ 2 CONTROLS AND FEATURES ..............4 CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) ..............6 PREPARATION ..................8 BASIC MENU OPERATIONS (MAIN MENU, SETUP MENU) ..............9 HOW TO USE “MAIN MENU”............... 10 HOW TO USE “SETUP MENU” ............13 HOW TO USE EXTERNAL CONTROL .......... -
Page 4: Controls And Features
CONTROLS AND FEATURES FRONT VIEW <Front Panel> UNDER PULSE COLOR DEGAUSS SCAN CROSS SLOT 1 SLOT 2 POWER SLOT 3 VOLUME MENU BLUE ASPECT AREA INPUT SELECT CHECK MARKER 9 10 11 12 16 17 18 19 20 21 22 23 UNDER PULSE COLOR... -
Page 5: Rear Panel
REAR/SIDE VIEW <Rear Panel> <Side Panel> REMOTE MAKE RS-232C MAIN POWER COLOR OFF button/lamp Refer to pages 8 and 9 for correspondence between the input terminals and the INPUT SELECT buttons. Press the COLOR OFF button. The button lights and the screen becomes monochrome. -
Page 6: Controls And Features (Input Card: Optional)
CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) COMPONENT/RGB INPUT CARD (OPTIONAL: IF-C01COMG) Video input/output terminals Input (IN) and output (OUT) terminals for component (color deference) or RGB signals. The IN and OUT terminals are bridge-connected. (When no cable is connected to the OUT terminal, the input signal is automatically terminated.) /B-Y Select component signal : press INPUT SELECT A/C/E... - Page 7 SDI INPUT CARD (OPTIONAL: IF-C01SDG) Output terminal for a selected component serial digital signal Output terminal for s selected digital signal (the input SWITCHED displayed on the screen). The output signal is cable- compensated. NOTE: When the monitor’s power is OFF, no digital signal is output.
-
Page 8: Preparation
PREPARATION INSTALLING THE INPUT ATTACHING THE WIDE CARD MASK Optional input cards are necessary to use the functions of this A wide mask is provided with the monitor. This changes the monitor. Before mounting the monitor or connecting other viewable screen area to the 16:9 aspect ratio. equipment to the monitor, be sure to install the input cards. -
Page 9: Basic Menu Operations (Main Menu, Setup Menu)
BASIC MENU OPERATIONS (MAIN MENU, SETUP MENU) ABOUT MENU SCREENS BASIC MENU OPERATION ● To select an item, This monitor features a MAIN MENU (main menu screen) and a SETUP MENU (setup menu screen). Press the buttons to move the cursor (4) on the The MAIN MENU contains the functions normally used, and Menu Screens and select the desired item. -
Page 10: How To Use "Main Menu
HOW TO USE “MAIN MENU” “MAIN MENU” ITEMS The following items appear in MAIN MENU. Items Functions Displays APERTURE CONTROL Compensates the frequency characteristics of the input video signal. SLOT CONDITION Displays the status of the input cards installed in each of the input card slots. sub menu POSITION Selects the display position of the sub menu superimposed on the screen. - Page 11 ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS 1. APERTURE CONTROL 3. sub menu POSITION Compensates the frequency Items : Selects the display position of the sub menu characteristics of the input superimposed on the screen. video signal. Press the Settings : UPPER/LOWER button to display the setting Functions : UPPER : An adjustment item is displayed on the menu illustrated on the right.
- Page 12 5. AREA MARKER-R R-Y PHASE Items : Selects the size marker for the other screen ratio R/B GAIN 0.79 (aspect) used when the screen ratio is 16:9. (for ITU601 external control) G-Y PHASE Settings : OFF/4:3/16:9/14:9/13:9/MODE 1/MODE 2 G/B GAIN 0.45 Functions : OFF: The marker is not displayed.
-
Page 13: How To Use "Setup Menu
HOW TO USE “SETUP MENU” “SETUP MENU” ITEMS Items Functions 1 FUNCTION SETTING Displays the monitor’s power-up time or the total usage time. 2 PICTURE SUB ADJ. Performs approximate adjustments using the control knobs on the front panel. 3 COLOR TEMP./BAL. Sets or adjusts the color temperature or white balance. - Page 14 HOW TO USE “SETUP MENU” (cont'd) ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS 1. FUNCTION SETTING Item : CONTRAST Selects the color system and Adjustment displays the monitor’s power- range : –20 ~ 00 ~ +20 up time or the total usage time. Function : For approximate adjustment of the picture Press the...
- Page 15 3. COLOR TEMP./BAL. 4. SIZE/POSI. ADJ. Sets or adjusts the color Adjusts the size or position of temperature or white balance. the picture. Press the Press the button to display button to display the setting the setting menu illustrated on menu illustrated on the right.
- Page 16 5. DISTORTION ADJ. 6. STATUS DISPLAY Compensates the picture Makes the status of the input distortion. Press the button signal appear or disappear on to display the setting menu the screen. Press the illustrated on the right. button to display the setting menu illustrated on the right.
-
Page 17: How To Use External Control
HOW TO USE EXTERNAL CONTROL ABOUT EXTERNAL CONTROL This multi-format monitor has two external control terminals. One is the MAKE terminal, which controls the monitor by connecting the terminals with many functions to the ground (GND) terminal. The other is the RS-232C terminal, which allows the monitor to be controlled by a PC via serial communication. - Page 18 HOW TO USE EXTERNAL CONTROL (cont.) HOW TO USE THE RS-232C TERMINAL You can control the monitor from your PC via the RS-232C terminal. For details on operating the monitor from the PC, consult your dealer or service center for details. 1.
-
Page 19: Troubleshooting
TROUBLESHOOTING Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance. Reference Problems Points to be checked... - Page 20 TROUBLESHOOTING (cont.) Reference Problems Points to be checked Measures (Remedy) pages Irregular color Is the monitor placed or moved close to Move the device away from the monitor. Press the DEGAUSS button on the front panel to a speaker or any other device degauss the screen.
-
Page 21: Specifications
SPECIFICATIONS Type : Multi-format monitor Remote Inputs : • Point-of-contact connection, 1 line, Picture Tube : 17" measured diagonally D-sub connector (15-pin 3-line) Effective • Serial connection, 1 line, D-sub connector Screen Size : Width : 13" (330 mm) (9-pin), compliant to RS-232C Height : 9-7/8"... - Page 22 Compliant Signal Formats of Each Input Card Input Signals IF-C01PNG IF-C01COMG IF-C01SDG NTSC — — — — Black-and-White (50 Hz/60 Hz) — — 480/60i (525i) — 480/60p (525p) — — 576/50i (*1) — 576/50p (*1) — — 720/60p (720p) — —...
- Page 23 SPECIFICATIONS (INPUT CARD: OPTIONAL) IF-C01COMG: COMPONENT/RGB INPUT CARD Type : Component/RGB input card for multi-format monitor Inputs/Outputs : Component (Y, P /B-Y, P /R-Y) or RGB: 1 line, BNC connector x 6 Synchronised signal (HD/C , VD) : 1 line, BNC connector x 4 * The input (IN) and output (OUT) terminals are bridge-connected.
- Page 24 A, C, E Signal from SDI 1 B, D, F Signal from SDI 2 JVC PROFESSIONAL PRODUCTS COMPANY DIVISION OF US JVC CORP. 1700 Valley Road Wayne, N.J. 07470 JVC CANADA INC. 21 Finchdene Square, Scarborough Ontario M1X 1A7 Printed in Japan LCT0971-001A ©...