Local Codes; Product Features; Glossary Of Terms; Pre-Installation Preparation - Desa CDVBPC Operation And Installation Manual

Desa owner's operation and installation manual iron stove and direct-vent (freestanding fireplace heater) burner system
Table of Contents

Advertisement

LOCAL CODES

4

PRODUCT FEATURES

GLOSSARY OF TERMS

PRE-INSTALLATION PREPARATION

Location and Space Requirements
LOCAL CODES
Install and use stove and burner system with care. Follow all local
codes. In the absence to local codes, use the current National Fuel
Gas Code ANSI Z223.1/NFPA 54* (USA) or the current CSA-
B149.1 Installation Code (Canada).
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
PRODUCT FEATURES
OPERATION
This cast iron stove with burner system is clean burning and vents
easily through outside walls or vertically using outside air for
combustion. Heat is generated by both realistic flames and glowing
embers. When used without the blower accessory, the stove with
burner system requires no electricity making it ideal for emergency
backup heat.
PIEZO IGNITOR
This burner system has a piezo ignitor. This system requires no
matches, batteries, or other sources to light burner system.
GLOSSARY OF TERMS
Chase
- A boxlike enclosure to protect venting from the elements
when the venting run is on the outside of a structure.
Mastic
- A pliable sealant for use around the vent terminal.
- A box that raises the horizontal termination
Snorkel Termination
above ground level clearances.
- Mounted on an outside wall or roof to separate the
Vent Terminal
inlet and outlet of the vent system and protect it from weather.
- A metal box that separates the vent cap from
Vinyl Siding Standoff
vinyl siding.
Wall Thimble/Firestop
- A metal plate used to secure the vent pipe
when it passes through a wall or ceiling.
For more information, visit www.desatech.com
For more information, visit www.desatech.com
PRE-INSTALLATION
PREPARATION
WARNING: A qualified service person must in-
stall stove and burner system. Follow all local codes.
CAUTION: This stove with burner system creates
warm air currents. These currents move heat to wall
surfaces next to stove. Installing stove next to vinyl
or cloth wall coverings or operating stove where
impurities (such as, but not limited to, tobacco smoke,
aromatic candles, cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may discolor walls or
cause odors.
LOCATION AND SPACE REQUIREMENTS
Determine the safest and most efficient location for your Comfort
Glow cast iron stove. Make sure that rafters and wall studs are not
in the way of the venting system. Choose a location where the heat
output is not affected by drafts, air conditioning ducts, windows, or
doors. Figure 2 shows some common locations. Read all venting
information in this manual. Be aware of all restrictions and precau-
tions before deciding the exact location for your stove.
When deciding the location of your stove, follow these rules:
1. Do not connect this stove and burner system to a chimney flue
serving a separate solid-fuel burning fireplace or appliance.
2. Due to high temperatures, do not locate this stove in high traf-
fic areas or near furniture or draperies.
3. Proper clearances must be maintained, see Figures 3 and 4 on
page 5.
4. This stove is a freestanding unit designed to set directly on the
floor. If your stove is to be installed directly on carpeting, vi-
nyl tile, or any combustible material other than wood, it must
be installed on a metal or wood panel extending the full width
and depth of the stove. See Figure 5, page 5.
On Wall with
Horizontal
Termination
On Wall with
Vertical Termination
Through Ceiling
Figure 2 - Common Stove Locations
Corner Installation
105501-01F

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cdvbnc

Table of Contents