Troubleshooting; Handle Light Troubleshooting (Q320) - Weber Q-320 Owner's Manual

PRobLEm
burners burn with a yellow or orange flame, in
conjunction with the smell of gas.
symptoms:
burners do not ignite, oR burners have a small,
flickering flame in the hi position, oR barbecue
temperature only reaches 250° to 300° in the hi
position.
burner does not light oR flame is low in hi position.
burner does not ignite when you push the ignition
button.
experiencing flare-ups:
m CAution: do not line the cookbox
with aluminum foil.
burner flame pattern is erratic, oR flame is low when
burner is on hi, oR flames do not run the whole
length of the burner tube.
inside of lid appears to be "peeling" (resembles paint
peeling).
if problems cannot be corrected by using these methods, please contact the Customer service Representative in your area using the contact information on our
web site. log onto www.weber.com
PRobLEm
Grill out handle light does not light.
®
if problems cannot be corrected by using these methods, please contact the Customer service Representative in your area using the contact information on our
web site. log onto www.weber.com
To replace batteries, remove lightpod by removing screw (1). Push tab (2) and pull apart.

TRoUbLESHooTING

Inspect spider / insect screens for possible obstructions
(blockage of holes).
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have been
activated.
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does the outside burner light with a match?
Be sure that there is gas flow to the burners by
attempting to match light your burners. Refer to
"MANUAL IGNITION."
Is there is a fresh battery installed?
Are the wires connected properly to the ignition module?
Is there plastic wrapping around the new battery?
Is burner tube positioned too far away from the igniter
electrode?
Are you preheating barbecue in the prescribed manner?
Are the cooking grates heavily coated with burned-on
grease?
Is the cookbox dirty and not allowing grease to flow into
catch pan?
Are burners clean?
The inside of the lid is cast aluminum and is not painted.
It cannot "peel." What you are seeing is baked-on grease
that has turned to carbon and is flaking off.
this is not A defeCt.
.
®

HANDLE LIGHT TRoUbLESHooTING (Q320)

Are the batteries old?
Are the batteries installed correctly?
Is the lid in the up position with the power button ON?
Is the Grill Out
.
®
cHEcK
cHEcK
Handle Light activated?
®
2
SoLUTIoN
Clean spider/insect screens. Refer to "ANNUAL
MAINTENANCE."
To reset the excess flow safety device, close the LP
tank valve and turn all burner control knobs to the OFF
position. Open the grill lid. Slowly turn the LP tank valve
until it is completely open. Wait at least one minute; then
ignite your grill. Refer to "IGNITION."
Refill LP cylinder.
Straighten fuel hose.
If you can light the outside burner with a match, then
check the ignition system.
If match lighting is successful, the problem lies in the
ignition system. Refer to "MAINTENANCE."
Verify that the battery is in good condition and installed
correctly. Refer to "BEFORE USING THE BARBECUE."
Be sure that wires are correctly inserted into terminals on
ignition module. Refer to "MAINTENANCE."
Remove plastic wrapping.
Check that the burner tube is positioned correctly to the
igniter electrode. Refer to "MAINTENANCE."
All burners on HI for 10 to 15 minutes for preheating.
Clean thoroughly. Refer to "CLEANING."
Clean cookbox.
Clean burners. Refer to "MAINTENANCE."
Clean thoroughly. Refer to "CLEANING."
SoLUTIoN
Replace batteries.
Refer to assembly illustration.
Light will activate when lid is open.
Press the power button.
1
WWW.WEbER.com
® 31