Manual Timer Programming; Vps/Pdc Recording - JVC DR-M100S Instructions Manual

Manual Timer Programming

You can programme this unit to timer record as many as
8 programmes up to 30 days in advance. If you do not know the
PlusCode number for the programme you wish to record, use the
following procedure to set your unit to timer record the programme.
●
Turn on the unit.
●
Turn on the TV and select an input mode such as EXT1.
●
Make sure that the unit's built-in clock is set properly.
1
Load a recordable disc.
●
For details, refer to APlacing A DiscB (A pg. 9).
2
Press PROG to display
the APROGRAMME
CHECKB screen.
●
When APROGRAMME
FULL DELETE
UNWANTED TIMER
PROGRAMMEB appears
on the TV screen, you
need to cancel some of
the reserved
programmes.
3
Press selection keys
repeatedly to select
ANEW TIMER
PROGRAMMEB, then
press ENTER.
4
Press selection keys to
set the desired date
(ADATEB), then press E.
5
Press selection keys to
set the desired start
time (ASTARTB), then press E.
Each press of F G increases/decreases the start time in
●
1 minute interval.
●
To increase/decrease the start time in 30 minutes interval,
press and hold F G.
TIMER j
PROG
Selection Keys
(FGDE)
ENTER
PROGRAMME CHECK
DATE START-STOP TV PROG DAILY/WEEKLY
19:00 - 20:00
05/07 SAT 44 WEEKLY
22:00 - 22:30
10/07 THU 10
13:30 - 14:00
11/07 FRI 26
16:00 - 17:00
11/07 FRI 33
++++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++++
DISC TIMER PRGM
EXIT OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
TIMER PROGRAMME
DATE START STOP
20:00 20:30
05/07 SAT
DAILY/WEEKLY VPS/PDC REC MODE
LP
OFF
EXIT
CONFIRM
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
6
Press selection keys to set the desired stop time (ASTOPB),
then press E.
Each press of F G increases/decreases the stop time in
●
1 minute interval.
●
To increase/decrease the stop time in 30 minutes interval,
press and hold F G.
7
Press selection keys to set the desired channel (ATV PROGB),
then press E.
8
Set the other recording options as required.
●
Refer to step 6 in AVIDEO Plus+ Timer ProgrammingB
(A pg. 38).
9
Press ENTER to access the Programme Confirmation screen.
10
Press ENTER to complete the timer programming.
● To programme another timer, repeat steps 2 - 10.
11
Press TIMERj to engage the unit's timer mode.
● The unit turns off automatically and j appears on the front
display panel.
●
To disengage the timer mode, press TIMERj again.
NOTES:
●
When two successive programmes are recorded with the
AManual Timer ProgrammingB function, the ending of the first
programme or the beginning of the second programme may not
be recorded.
●
If the copy limited programme is received during timer recording,
the unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Satellite Receiver Users
To record a satellite broadcast using Manual Timer
Programming:
A Perform Manual Timer Programming.
B Set the satellite receiver to the appropriate channel for
recording.
●
Leave the satellite receiver's power on.

VPS/PDC Recording

Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are services
designed to assure safe, accurate timer recording. With this
system, special code signals are transmitted together with the
audio/video signals. These code signals control your unit and have
precedence over the advertised times you may have preset into
VPS/PDC REC MODE
the timer. This means that your unit will start and stop recording
ON
SP
ON
XP
when the preset TV programmes actually start and end^even if
OFF
LP
OFF
LP
the broadcast time of a preset TV programme is changed from
what has been advertised. PDC is currently available nationally on
BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay
transmitters. Ch.3 operates a PDC service in some areas. All
channels intend to offer this service in due course. Check your TV
programme listing guide for latest information. If the channel you
intend to record does not offer a PDC service your unit will not start
recording if PDC has been selected. Be sure to set PDC to AOFFB if
PDC is not available on your selected channel. (See step 6 on
page 38.).
NOTES:
TV PROG
VTM 10
●
When you use Manual Timer Programming, set the start time
(VPS or PDC time) exactly as advertised in the TV listing. A
different time than advertised will result in no recording.
NAME
●
VPS/PDC recording is also possible via the [L-1 IN/OUT]
connector.
TIMER RECORDING
39
EN