UJ ------- U.S.A Militaly RAM/RW STANDBY/ON PUSH-OPEN DR-M100SUS, DR-M100SUC, DR-M100SUJ [D5R10] Since the whole mechanism assembly unit is replaced, the DVD recorder mechanism of this unit need not be adjusted. TABLE OF CONTENTS PRECAUTION............... . . 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
SPECIFICATION DR-M100SUS,DR-M100SUC DR-M100SUJ GENERAL Power requirement AC 120 V~, 60 Hz AC 220 V-240 V~,50/60 Hz Power consumption Power on : 30 W Power on : 29 W Power off : 2.7 W Power off : 5.2 W Temperature Operating : 5°C to 35°C(41°F to 95°F) Storage : -20°C to 60°C(-4°F to 140°F)
SECTION 1 PRECAUTION Safety Precautions (1) This design of this product contains special hardware and voltmeter. many circuits and components specially for safety purpos- Move the resistor connection to each exposed metal es. For continued protection, no changes should be made part, particularly any exposed metal part having a return to the original design unless authorized in writing by the path to the chassis, and measure the AC voltage across...
Page 4
Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players or recorder.
Page 5
Important for laser products Importance administering point on the safety W1613 IC5309 CN3002 CN5305 C5319 W248 W263 W613 W255 CN4001 W833 W249 W262 W251 W813 CN3901 CN3001 W247 W237 C3011 D5315 L3001 W245 C5310 R5320 C5315 W244 C8027 W242 W1814 W608 X3001 W239...
Page 6
Important for laser products 5.CAUTION : If safety switches malfunction, the laser is able 1.CLASS 1 LASER PRODUCT to function. 2.DANGER : Invisible laser radiation when open and inter 6.CAUTION : Use of controls, adjustments or performance of lock failed or defeated. Avoid direct exposure to beam. procedures other than those specified here in may result in 3.CAUTION : There are no serviceable parts inside the hazardous radiation exposure.
SECTION 3 DISASSEMBLY Main body section 3.1.1 Remove the top cover (See figure 1) (1) Remove the four screws A attaching the top cover on both sides of the main body. (2) Remove the five screws B attaching the top cover on the TOP COVER TOP COVER TOP COVER...
Page 9
3.1.3 Remove the drive unit (See figure 4) Digital board CN1101 Drive unit • Prior to performing the following procedure, remove the top CN1801 cover. • There is no need to remove the front panel assembly. on the (1) Disconnect the socket wire from connector CN5302 main board.
Page 10
3.1.5 Remove the main board (See figure 5, figure 6) • Prior to performing the following procedure, remove the top CN1101 CN4001 Display board cover, drive unit. Digital board CN7001 CN5001 (1) Disconnect the card wire from connectors CN4001, CN4103 on the main board.
Page 11
Loading mechanism assembly 3.2.1 Remove the clamper base (See figure 1, figure 2) (1) The part a on the reverse side of a mechanism assembly is made to slide in the direction of an arrow with a driver etc. (A tray ejects a few.) (2) Remove the two screws A attaching the clamper base.
Page 12
3.2.2 Remove the traverse mechanism assembly (See figure 3, figure 4, figure 5) • Prior to performing the following procedure, remove the clamper base and tray. (1) It solder to part b section on the pick-up unit. Pick-up unit Leaf spring Part b Pick-up unit (2) Disconnect the card wire from connector...
Page 13
3.2.3 Remove the flexible wire assembly (See figure 6) • Prior to performing the following procedure, remove the Part c Spindle motor assembly clamper base and tray. (1) Remove the four screws G and H attaching the flexible wire assembly. (2) Remove the solder part c soldered to the feed motor.
SECTION 5 TROUBLESHOOTING JIG Mode The following remote control units are required to set and cancel JIG mode. For setting : a remote control unit attached to product. For cancellation : JIG remote control unit (part number : PTU94023B) Remote control unit JIG remote control unit attached to product JIG remote control unit...
Page 16
5.1.1 Setting JIG mode To display SYSTEM INFO or to upgrade firmware, the main body needs to be set to JIG mode. (1) Turn the main body ON. (2) Press the buttons of the remote control unit attached to product in the following order : "SET UP" → "2" → "8" → "ENTER" (3) When a colon ":"...
Page 17
Displaying SYSTEM INFO In the SYSTEM INFO there is information including firmware versions of the main body and the drive unit. (1) Set the main body to JIG mode. (2) Transmit "43-8B" to the main body by using JIG remote control unit. (Please end a setting menu pushing “SET UP”...
Page 18
Updating the firmware of the main body • Firmware update disk supports CD-R media. • When firmware update is necessary. information is available from the homepage of DIGITAL VIDEO STORAGE CATEGORY, CS group. • Please check the details of the update disc creation method by JS-NET. (1) Set the main body to JIG mode.
Page 19
Taking out a disc 5.6.1 Method 1 There is compulsive tray ejection mode by electric operation. (1) AC Plug is pulled out at once and inserted again. (2) It is displayed on FL display as "LOADING", and while it blinks, pushing the EJECT button of a main body is continued. (3) After a while, a tray opens (About 20 seconds).
Page 20
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY DIGITAL VIDEO STORAGE CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan (No.YD058) Printed in Japan...
UC -------------- Canada UJ ------- U.S.A Militaly RAM/RW STANDBY/ON PUSH-OPEN DR-M100SUS, DR-M100SUC, DR-M100SUJ [D5R10] Since the whole mechanism assembly unit is replaced, the DVD recorder mechanism of this unit need not be adjusted. No.YD058SCH COPYRIGHT 2005 Victor Company of Japan, Limited...
Page 22
CHARTS AND DIAGRAMS NOTES OF SCHEMATIC DIAGRAM 4. Voltage measurement 1) Regulator (DC/DC CONV) circuits Safety precautions REC : Colour bar signal. The Components indentified by the symbol PB : Alignment tape (Colour bar). critical for safety. For continued safety, replace safety —...
Page 23
CIRCUIT BOARD NOTES 1. Foil and Component sides 1) Foil side (B side) : Parts on the foil side seen from foil face (pattern face) are indicated. 2) Component side (A side) : Parts on the component side seen from component face (parts face) indicated.
Wiring diagram [no pin] BB[AL5V] AUDIO IN AUDIO IN CH SW MOD SDA SW5V MB[SW5V] CONV.CTL[H] MOD SCL SW5V VIDEO IN SW-12V VIDEO IN AS/[no pin] SW+12V TU[30V] RF AGC D.GND UEC956 AUDIO OUT SIF OUT AUDIO OUT TU[30V] SIF OUT TU[30V] VIDEO OUT 5.8V...
Page 28
DIGITAL 5 0 J4112 IEEE1394 TPA+ TPA- TPB+ TPB- IEEE1394 controller terminal PHY_RESET[L] IC1801 PHY_LREQ PHY_CLK PHY_CNA PHY_CTL[0],[1] PHY_DATA[0-7] PHY_LPS PHY_LINK_ON IEEE1394 section (SHEET 8) SDRAM_DQ16 to 31 RA1613 to DDR_DQ16 to 31 RA1616 SDRAM_A_17 DDR SDRAM DDR SDRAM RA1609 to SDRAM_DQ0 to 15 DDR_DQ0 to 15 IC1601...
Page 29
E1394 minal VI_D2 to D9 VIDEO_27M E5_RESET_L SIO_SCL SIO_SDA Video decoder IC1901 C_IN VY_IN Video decoder section (SHEET 11) ATA_DMAACK[L] ATA_INTRQ ATA_ADD0 to 4 ATA_DIOR[L] ATA_DIOW[L] ATA_IORDY ATA_DAT0 to 15 ATA_RESET ATA_DMARQ To Front end board of drive unit ATAPI Interface section (SHEET 12) MADD1 to 22 64Mbit Flash IC1201...
Page 30
MAIN 0 3 -29V DC3.9V[+/-] TO SHEET 7 AC-DC AC IN D5001 SW-12V SW12V SW5V AL5.8V D1.8V D2.5V TO each sheet FAN_CTL P.CTL[H] DVD_P.CTL[H] Power TO SHEET 5 transformer P.SAVE[L] T5001 Switching regurator IC5101 TO Fan assembly 5V REG. TO each sheet IC5303 DV5V REG.
Page 31
mbly SW/JACK 2 7 Operation switch KEY1,KEY2 S7132 S7135 S7112 to S7115 BLUE_LED LIGHTING D7111 J7001 Front S-video IN FRONT_C/Y_IN J7002 FRONT_VIDEO_IN TO CN4001 SHEET 3 Front A/V IN FRONT_A[L/R]_IN Operation switch section (SHEET 7) 2-10...
Page 32
L5206 D5214 R5315 C5209 C5308 C5316 R530 D5211 Q5313 C5210 R5308 * Refer to the "JVC" column of a table for this model. Parts are safety assurance parts. When replacing those parts make sure to use the specified one. 2-11...
Page 33
DC3.9V[+] Q5301 R5319 DC3.9V[-] SHEET 7 -29V SW-12V FAN_CTL P.CTL[H] SW12V Q5304 R5320 R5321 SW5V TO each AL5.8V R5322 P.SAVE[L] sheet R5323 HDD_P.CTL[H] Q5305 3.3V C5309 DVD_P.CTL[H] Q5303 R5312 Q5307 R5324 Q5302 Q5306 R5313 CN5303 R5310 R5311 TO FAN UNIT D5317 IC5308 Q5316...
Page 46
IEEE1394 Section D I G I T A L ( 1 3 9 4 P H Y ) 2 4 . 5 7 6 M I C 1 8 0 1 T S B 4 1 A B 2 P A P F R O M / T O M E D I A P R O C E S S O R PHY_RESET_L...
Page 47
K 1 8 0 2 N Q R 0 0 2 2 - 0 0 2 X R 1 8 2 0 1 0 k C 1 8 0 3 2 2 / 6 . 3 C N 1 8 0 2 Q G F 1 0 1 6 C 2 - 0 7 W A G N D G N D...
Page 48
DDR SDRAM Section D I G I T A L ( D D R _ S D R A M ) S D R A M _ D Q _ 0 D D R _ D Q _ 0 D D R _ D Q _ 0 S D R A M _ D Q _ 1 R A 1 6 0 9 D D R _ D Q _ 1...
Page 49
D D R _ S D R A M D D R _ D Q _ 1 6 R A 1 6 2 1 D D R _ D Q _ 1 7 1 0 0 D D R _ D Q _ 1 8 D D R _ D Q _ 1 9 D D R _ D Q _ 2 0 R A 1 6 2 2...
Page 50
Media processor section F R O M / T O D D R S D R A M S D R A M _ D Q _ [ 0 - 1 5 ] S D R A M _ D Q _ [ 1 6 - 3 1 ] S D R A M _ D Q S _ [ 0 - 3 ] S D R A M _ D Q M _ [ 0 - 3 ] S D R A M _ A _ [ 0 - 1 2 ]...
Page 51
R 1 4 9 5 1 0 k F R O M / T O 1 3 9 4 P H Y TO SHEET 8 P H Y _ R E S E T _ L R 1 4 5 6 F R O M / T O 1 0 0 D I G I J U N C T I O N...
Page 52
Video decoder section D I G I T A L 2 2 / 6 . 3 2 2 / 6 . 3 C 1 9 0 1 C 1 9 0 2 ( T I _ D E C ) F R O M / T O D I G I J U N C T I O N K 1 9 0 1...
Page 53
T L 1 9 0 4 T L 1 9 0 5 T L 1 9 0 3 T L 1 9 0 2 V S Y N C / P A L I T L 1 9 0 1 F I D / G L C O S D A R 1 9 1 2...
Page 54
ATAPI Interface section A T A _ A D D _ 0 A T A _ A D D _ 1 A T A _ A D D _ 2 F R O M D I G I J U N C T I O N D 3 .
Page 55
D I G I T A L F R O M / T O D R I V E R 2 2 0 4 C N 2 2 0 1 Q G F 0 5 0 3 C 1 - 4 0 V R S D A T A K 2 2 0 1 N Q R 0 0 2 2 - 0 0 2 X...
Page 56
FLASH-ROM section L H _ A R _ 1 7 1 6 0 8 S H O R T K 1 2 0 1 L H _ A R _ 1 6 A 1 5 A 1 6 L H _ A R _ 1 5 A 1 4 V C C Q L H _ A R _ 1 4...
Page 57
5 0 D I G I T A L I C 1 2 0 3 S N 7 4 L V C 3 7 3 A P W - X C 1 2 0 7 0 . 1 V C C L H _ A R _ 1 4 L H _ A R _ 2 1 M A D D _ 1 4...
Page 58
Digital junction section K 1 1 0 5 O P E N 5 0 D L C 1 1 0 1 N Q R 0 5 1 2 - 0 0 8 X C 1 1 0 1 C 1 1 0 6 C 1 1 1 1 C 1 1 2 5 C 1 1 2 6...
Page 59
T O D D R S D R A M S S T L 2 _ V D D 5 0 D I G I T A L TO SHEET 9 D 3 . 3 V G N D C 1 1 2 6 C 1 1 2 7 0 .
Page 62
COMPONENT PARTS LOCATION GUIDE <MAIN> LPB10288-001C Jack board <36> LP REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C5206 C8208 B C 20K R3204 B C 9L R5335 B C 4O R8507 B C 9B K4105 C3001 B C 15K...
Page 66
COMPONENT PARTS LOCATION GUIDE <DIGITAL> LPB10289-001C REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C1808 A C 2C R1449 B C 5C R10004 A C 1A RA1804 A C 3D C1101 A C 4A C1809 A C 2C R1450 B C 2E RA1901...
Page 68
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY DIGITAL VIDEO STORAGE CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan Printed in Japan No.YD058SCH...
* BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance. We recommend that genuine JVC parts be used. * (x_) in a description column shows the number of the used part.
Page 70
Exploded view of general assembly and parts list Block No.M1MM MAIN BOARD ASSY <03> DIGITAL BOARD ASSY<50> DISPLAY BOARD ASSY<28> JACK BOARD ASSY<36> CN5001 CN5303 CN451 CN5302 make a crease CN4103 Be careful not to damage FFC WIRE with BOTTOM CHASSIS. MAIN PWB ASS'Y CN2201 REFER TO FIG.6...
Page 72
DVD mechanism assembly and parts list Bl oc k No.M 2 M M CLAMPER SA NOTES: 1.Attach the MAGNET to the CLAMPER. 2.Lock the MAGNET and BACK YORK to the CLAMPER firmly with its 3 hooks. 3.Make sure that none of the 3 hooks of the CLAMPER is broken/ bent/ changed in shape.
Page 73
DVD mechanism Block No. [M][2][M][M] Symbol No. Part No. Part Name Description Local QAL0496-001 LP41195-001A BASE HOLDER QYSDSP2604ZA SCREW M2.6 x 4mm(x7) LP10566-001A LOWER CASE QAR0352-001 LOADING MOTOR LP41183-001A MOTOR PULLEY LP41117-001A SCREW (x2) LP31204-001A INSULATOR (x4) LP41186-001A GEAR 2 LP41187-001A GEAR 3 LP41185-001A...
Page 75
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C3029 NCB31CK-104X C CAPACITOR 0.1uF 16V K C5107 NDC31HJ-121X C CAPACITOR 120pF 50V J C3030 QEKJ0JM-476Z E CAPACITOR 47uF 6.3V M C5201 QEZ0562-227Z E CAPACITOR 220uF 6.3V M...
Page 76
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C8211 NCB31CK-104X C CAPACITOR 0.1uF 16V K R3227 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J C8212 QETJ1CM-107Z E CAPACITOR 100uF 16V M R3229 NRSA63J-103X MG RESISTOR 10kΩ...
Page 78
Digital board Symbol No. Part No. Part Name Description Local Block No. [5][0] C1442 NCB31CK-104X C CAPACITOR 0.1uF 16V K Symbol No. Part No. Part Name Description Local C1444 NCB31CK-104X C CAPACITOR 0.1uF 16V K C1445 NCB31CK-104X C CAPACITOR 0.1uF 16V K C1447 NCB31CK-104X...
Page 79
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R1223 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R1801 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R1224 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R1802 NRSA63J-101X MG RESISTOR 100Ω...
Page 80
Operation board Symbol No. Part No. Part Name Description Local Block No. [2][6] B1204 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J Symbol No. Part No. Part Name Description Local B1402 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J B1701 NRSA63J-0R0X MG RESISTOR 0Ω...
Page 81
Sw/Jack board Jack board Block No. [2][7] Block No. [3][6] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local LPA10281-01C2 SW/JACK BOARD ASSY LPA10288-04C2 JACK BOARD ASSY LPA10288-01C2 JACK BOARD ASSY UC,US D7113 1SS133-T2...
Page 82
Packing materials and accessories parts list Block No.M3MM ADHESIVE TAPE FINAL ASSY<M1> SPEC OF BARCODE 3-14(No.YD058)
Page 83
Packing and accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local LP31492-002A PACKING CASE LP31494-001B CUSHION ASSY QPC06005515P POLY BAG 60cm x 55cm QAM0501-003 RF CABLE QAM0522-001 A/V CABLE ------------ BATTERY R6TYPE(x2) QPC02202230P POLY BAG ACCESSORY ...