Manual Timer Programming - JVC ShowView LPT0923-001A Instructions Manual

TIMER RECORDING
46
EN

Manual Timer Programming

You can programme this unit to timer-record as many as
32 programmes.
If you do not know the S
HOW
wish to record, use the following procedure to set your unit to
timer-record the programme.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
AUX
ENTER
1
Load a recordable disc if recording to DVD.
2
Press PROGRAMME to access the programme top screen.
3
Press rtw e to select "CALENDAR PR.", then press ENTER.
When "PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES" appears on the TV screen, you need to cancel
some of the reserved programmes. (
4
Press rtw e to select the desired date, then press ENTER.
5
Press rt to select "RECORD
TO", then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
V number for the programme you
IEW
CABLE/SAT
TV DVD
PROGRAMME
rtwe
pg. 47)
2
PROGRAMME > CALENDAR PR. (2/3)
14/01/04 WED 22:30 - 23:00
RECORD TO
SELECT WITH [ ]
THEN PRESS [ENTER]
START
PRESS [PROGRAMME] STOP
TO EXIT
TV PROG
[0]: SAT
ENTER
PROGRAMME
CONFIRM
EXIT SELECT
6
Press rt to select "START", then press ENTER. Press rt to
set the desired start time, then press ENTER.
Each press of rt advances/goes back the start time in 1-min.
increments.
To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press rt to select "STOP", then press ENTER. Press rt to
set the desired stop time, then press ENTER.
Each press of rt advances/goes back the stop time in 1-min.
increments.
To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press rt to select "TV PROG", then press ENTER. Press rt
to select the desired channel.
9
Press rt to select "CONFIRM", then press ENTER.
10
Set the other recording options as required.
Refer to step 8 in "S
11
Press rt to select "OK",
then press ENTER to access the
Programme Confirmation screen.
12
Press w e to select "EXIT",
then press ENTER to complete
timer programming.
To programme another timer,
press w e to select
"CONTINUE", then press
ENTER.
If "PROGRAMME OVERLAPPED" appears on the TV screen, see
page 47.
NOTES:
When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform "Satellite Receiver Control Setting" (
B Perform "Manual Timer Programming" (
press AUX to change "TV PROG" to "SAT". Then press rt to
enter the channel position for the satellite broadcast.
C Leave the satellite receiver's power on.
Relief Recording
BBC1
[MISC. ] XP
When a programme that is set for the DVD deck cannot be
HDD recorded properly, the programme is recorded to the HDD deck
22:30
instead in the same recording mode as set.
23:00
If the remaining capacity of the hard disc is not sufficient, the
BBC1
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
If "JUST" is selected for the recording mode, the current recording
mode for the DVD deck is applied.
V TM Timer Programming" (
HOW IEW
14/01/04 WED 22:30 - 23:00
GARDENING
SELECT WITH [ ]
THEN PRESS [ENTER]
PRESS [PROGRAMME]
TO EXIT
PROGRAMME ENTER
EXIT SELECT
pg. 46). In step 8,
pg. 44).
2 PROGRAMME > CALENDAR PR. (3/3)
BBC1
[EDUCATION] FR360
1:00 28:00
INPUT TITLE GARDENING
CATEGORY EDUCATION
VPS/PDC OFF
WEEKLY/DAILY MON-FRI (FOR A WEEK)
REC MODE FR360
O K
pg. 23).