Harman Kardon AVR 147 Owner's Manual page 31

The first line indicates that the receiver is currently set to the tuner
source. In fact, you may hear static if the tuner is set to an unused
frequency. You will not be able to make any changes to the tuner, other
than selecting a component video input or adjusting the tone controls.
It is not recommended that you make either of these changes for
the tuner at this time.
Press the Button to view the next source. The sources will be selected in
‹
the following order: Tape, 6-Channel Inputs, XM Radio, DMP/The Bridge,
Video 1, Video 2, Video 3, HDMI 2, HDMI 1, DVD and CD. Pressing the
Button selects the sources in the reverse order.
›
For each of these sources, you may adjust the following settings. At a
minimum, you should make sure that sources connected to any of the
component video or digital audio inputs have the correct settings. Other
settings are optional, and you may adjust them at a later time when you
have more experience with the AVR. Refer to the Table A4 worksheet in
the appendix that you filled out during installation as you assign inputs
to each source.
TITLE: You may change the display name for any source (except the
tuner). Not only does this enable you to customize your system; it helps
you to select the correct source device even when you have forgotten
which physical connections you used.
Move the cursor down to the TITLE line and press the Set Button.
A block cursor will blink. See Figure 52.
Figure 52 – Retitling a Source Input
Now you may use the ⁄ / ¤
upper and lower case, as well as numbers and a variety of punctuation
marks. When you have selected the desired character, press the ›
Button to move to the next space. You may also press the › Button to
leave a blank. Press the Set Button when you have finished spelling out
the new display name for the source.
COMPONENT IN: If you connected the source to one of the two compo-
nent video inputs, make sure the correct set of inputs is displayed at this
line. If it isn't, move the cursor to this line, and then press the › Button to
change the setting.
Buttons to scroll through the alphabet in
INITIAL SETUP
AUDIO IN: By default, the analog audio inputs are assigned to all
sources at the factory, with the following exceptions:
Table 4 – Default Digital Audio Assignments
Source Input Default Digital Audio Input
DVD Coax 1
Video 2 Optical 1
HDMI 1 Coax 2
HDMI 2 Optical 2
If you used a digital audio connection for another source, change this
setting to assign the correct digital audio input to the source, even if you
also connected the analog audio outputs of the source to the receiver.
Move the cursor to this line, and press the
correct digital input appears.
AUTO POLL: The Auto Poll feature is used when both an analog
audio and digital audio connection have been made for one source
device. If for some reason no digital signal is available, the AVR 147
will switch to the analog inputs for the source. This situation can occur
with some cable or satellite television broadcasts, where some channels
are broadcast with digital audio and others with analog audio.
For some sources, the Auto Poll feature is unnecessary and may be
undesirable. For example, if your DVD player is stopped, you may not
want to use the analog audio signal or you may have decided not
to connect analog audio. Move the cursor to this line, and press the
Buttons until OFF appears, disabling the Auto Poll feature. With Auto Poll
turned off, the receiver will only check for a signal at the
audio input assigned to the source.
DMP SETTING: If you select DMP/The Bridge as your source input,
you will notice that the AUDIO IN line of the INPUT SETUP menu has
been replaced by the option GO TO DMP SETTING. See Figure 53.
Figure 53 – Input Setup Menu Screen for DMP/The Bridge source
Since The Bridge is connected to the AVR using a dedicated connection,
it isn't possible to select a different audio input for this source. However,
there are several special settings used only with The Bridge. Selecting
GO TO DMP SETTING displays the DMP SETTING menu (see Figure 54).
‹ / › Buttons until the
‹ / ›
31