Denon AVR-4311CI Owner's Manual page 139

Symptom
Audyssey DSX™ • Check that "Speaker Config." – "Front Height" or "Front Wide" is
cannot be selected. set to other than "None".
Or "Not Available" • Check that "Speaker Config." – "Center" is set to other than
is displayed when "None".
AUDYSSEY DSX
• Switch the surround mode to STANDARD.
button is pressed. • Check that "Input Mode" is set to other than "EXT.IN".
• When headphones are used, Audyssey DSX cannot be selected.
MultEQ ® XT 32,
• Switch the surround mode to other than "DIRECT"or"PURE
Dynamic EQ ® and
DIRECT".
Dynamic Volume ®
• Check that "Input Mode" is set to other than "EXT.IN".
cannot be selected. • When headphones are used, MultEQ XT 32, Dynamic EQ and
Or "Not Available" Dynamic Volume cannot be selected.
is displayed when
MULTEQ
button or
DYN EQ/VOL
button
is pressed.
Dynamic EQ and • Make Audyssey Auto Setup.
Dynamic Volume
cannot be selected.
Or "Run Audyssey
Auto Setup" is
DYN
displayed when
EQ/VOL
button is
pressed.
RESTORER cannot • Check that an analog signal or PCM signal （fs=44.1/48kHz） is
be selected. Or
input. For playback of multichannel signals such as Dolby Digital or
"Not Available" is
DTS surround, RESTORER cannot be used.
displayed when the
• Check that "Input Mode" is set to other than "EXT.IN".
RESTORER
button is
pressed.
136
Cause/Solution
GHDMIH
Page
Symptom
96
No audio is • Check the connection of the HDMI connectors.
output with HDMI • When outputting HDMI audio from the speakers, set "HDMI
96
connection. Audio Out" on the menu to "AMP".
• When outputting HDMI audio from a TV, set "HDMI Audio Out"
50
on the menu to "TV".
84
–
No video is • Check the connection of the HDMI connectors.
output with HDMI • Set the input source to match the connected HDMI connector.
52
connection. • Check whether the TV is compatible with copyright protection
(HDCP). If connected to a device not compatible with HDCP, video
84
will not be output correctly.
–
When the following • Set "HDMI Control" on the menu to "OFF". To operate power
operations are only for each device, set "Power Off Control" to "OFF".
performed on
devices compatible
with HDMI control,
the same operations
7, 63
occur on this unit.
• Power ON/OFF
• Switching audio
output devices
• Adjust volume
• Switch input source
GSIRIUS Satellite RadioH
92
Symptom
"CHECK SIRIUS • The SiriusConnect Home Tuner unit is not connected. Check that
TUNER" is displayed. the connections are correct.
84
"ANTENNA ERROR" • The antenna is not connected. Check that the connections are
is displayed. correct.
"NO SIGNAL" is • The antenna is not connected. Check that the connections are
displayed. correct.
"INVALID • Channel is not present. Select another channel.
CHANNEL" is
displayed.
"ACQUIRING • The signal cannot be received. Reposition your SiriusConnect
SIGNAL" is Home Tuner and Home Dock antenna.
displayed. • Displays while SiriusConnect Home Tuner is connected. Reposition
your SiriusConnect Home Tuner and Home Dock antenna.
"Call SIRIUS" z is • Channels are not subscribed to. If you subscribe to the channel,
displayed. you can receive the channel.
"SUBSCRIPTION • While updating contract information.
UPDATED" is
displayed.
"Enter Lock Code • Selected channels are locked. Please insert pass word (4 digits)
[ ]" is displayed. into "[
z After scroll displays "Call 888-539-...." twice, displays "Call SIRIUS".
Cause/Solution
Cause/Solution
]"
Page
17
98
98
17
17, 28
16
65, 99
Page
23
23
–
–
–
–
–
–
–