Input/Output Characteristics - Yamaha CL3 Owner's Manual

Specifications

Input/output characteristics

ANALOG INPUT CHARACTERISTICS
Input
GAIN
Terminals
+66dB
+18dB
OMNI IN 1-8
+17dB
–6dB
+64dB
TALKBACK
+20dB
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum
gain. (all faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
*3. In these specifications, 0dBu= 0.775 Vrms.
*4. All input AD converters are 24bit linear, 128times oversampling.
*5. +48V DC ( phantom power ) is supplied to OMNI IN (1-8) and TALKBACK XLR type connectors via each individual software controlled
switches.
ANALOG OUTPUT CHARACTERISTICS
Output Actual Source
Terminals Impedance
OMNI OUT 1-8
PHONES
*1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
*2. PHONES stereo phone jack is unbalanced. (Tip= LEFT, Ring= RIGHT, Sleeve= GND)
*3. In these specifications, 0dBu= 0.775 Vrms.
*4. All output DA converters are 24bit, 128times oversampling.
*5. There are switches inside the body to preset the maximum output level.
*6. The position of the level control is 10dB lowered from Max.
DIGITAL INPUT & OUTPUT CHARACTERISTICS
Terminal
Primary/Secondary
DIGITAL OUTPUT CHARACTERISTICS
Terminal
DIGITAL OUT
*1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
I/O SLOT (1-3) CHARACTERISTICS
Each I/O Slot accepts a mini-YGDAI card. Only Slot1 has a serial interface.
CONTROL I/O CHARACTERISTICS
Terminal
MIDI
WORD CLOCK
GPI (5IN/5OUT)
NETWORK
LAMP (CL5: x3, CL3: x2, CL1: x1)
USB HOST
DC POWER INPUT
METER (CL3/CL1 only)
*1. Input pin: TTL level, w/ internal pull-up (47kΩ)
Output pin: Open drain output (Vmax=12V, maximum sink current/pin=75mA)
Power supply pin: Output voltage Vp=5V, Max. output current Imax=300mA
*2. 4pin= +12V, 3pin= GND, Lamp rating 5W. Voltage control by software.
56
Actual Load For Use With
Impedance Nominal
10kΩ
50-600Ω Mics
& 600Ω Lines
3kΩ
50-600Ω Mics
10kΩ
& 600Ω Lines
For Use With
GAIN SW
Nominal
+24dB (default)
75Ω 600Ω Lines
8Ω Phones
15Ω
40Ω Phones
Format Data length
Dante 24bit or 32bit
Format
AES/EBU AES/EBU Professional Use
Format
IN MIDI
OUT MIDI
IN –
OUT –
–
IEEE802.3
–
USB 2.0
–
–
Owner's Manual
Input Level
*1
Nominal
Sensitivity
–82dBu (61.6μV) –62dBu (0.616mV)
–34dBu (15.5mV) –14dBu (155mV)
–33dBu (17.4mV) –13dBu (174mV)
–10dBu (245mV) +10dBu (2.45V)
–70dBu (0.245mV) –60dBu (0.775mV)
–26dBu (38.8mV) –16dBu (0.123V)
Output Level
*5
Nominal
+4dBu (1.23V)
+18dB –2dBu (616mV)
*6
–
75mW
*6
–
65mW
Level
1000Base-T 64ch Input/64ch Output @48kHz
Data Length
24bit
Level
–
–
TTL/75Ω terminated
TTL/75Ω
–
10BASE-T/100Base-TX
*4
0V-12V
–
–
–
Max. before clip
–42dBu (6.16mV)
+6dBu (1.55V)
+7dBu (1.74V)
+30dBu (24.5V)
–40dBu (7.75mV)
+4dBu (1.23V)
Connector
Max. before clip
+24dBu (12.3V) XLR-3-32 type
+18dBu (6.16V) (Balanced)
150mW
Stereo Phone Jack (TRS)
(Unbalanced)
150mW
Audio Connector
EtherCON Cat5e
Level Connector
RS422
XLR-3-32 type (Balanced)
Connector
DIN Connector 5P
DIN Connector 5P
BNC Connector
BNC Connector
D Sub Connector 15P (Female)
RJ-45
*2
XLR-4-31 type
USB A Connector (Female)
JL05 Connector
D Sub Connector 9P (Female)
Connector
XLR-3-31 type
*2
(Balanced)
XLR-3-31 type
*2
(Balanced)
*1
*2
*1
*1