Yamaha CL3 Owner's Manual page 30

Basic operation of the CL series
4.
Select a target custom fader bank.
Channel strips are categorized into four blocks; from
your left, block A, block B (Centralogic section), block
C (only for CL5), and Master.
5.
Press the number in the FADER area, then
press the [SEL] key for the channel that you
want to assign to that fader.
You can also select a channel in the display. Press the
button below the desired number to display the CH
SELECT screen. First select the tab for a channel
group, then select individual channels. To return to
the previous screen, press the CLOSE button.
6.
Repeat step 5 to select all channels that you
want to assign to the custom fader bank.
7.
When you have finished, press the X symbol
in the upper right corner of the screen.
Adjusting the send level to a MIX bus or
MATRIX bus (SENDS ON FADER mode)
Each fader on the top panel enables you to adjust the level
of the corresponding channel, as well as the send level of
the signal routed from each channel to the
currently-selected MIX/MATRIX bus (SENDS ON
FADER mode).
Follow the procedure below to use the faders on the top
panel to adjust a signal that is sent from all input channels
to a specific MIX bus.
1.
In the function access area
in the display, press the
SENDS ON FADER button.
The CL will switch to SENDS
ON FADER mode. The most
recently selected group of
MIX/MATRIX buses will be
assigned to the Centralogic
section. The faders in the
Channel Strip section will move
to indicate the send level of the
signals that are routed from each
channel to the currently-selected
MIX/MATRIX bus.
In SENDS ON FADER mode,
the function access area in the
display will show the button that
enables you to switch between
30
1
2
Owner's Manual
MIX1–16 and MIX17–24/MATRIX, and the buttons
that enable you to select the destination
MIX/MATRIX buses.
1
ON FADER switch button
Pressing this button repeatedly will switch between
MIX1–16 and MIX17–24/MATRIX.
2
MIX/MATRIX bus select buttons
These buttons enable you to select the destination
MIX/MATRIX buses. Two buses that are paired in
stereo are represented by one button.
2.
Press the ON FADER switch button repeatedly
to select MIX1–16 or MIX17–24/MATRIX.
In this way, you can use the MIX/MATRIX bus select
buttons to specify the destination MIX/MATRIX
buses.
3.
Use the MIX or MATRIX bus select buttons in
the function access area to select the
send-destination MIX/MATRIX bus.
NOTE
• Alternatively, press a SEND LEVEL knob in the
SELECTED CHANNEL section to display a popup window,
from which you can select a MIX/MATRIX bus.
• You can also select a MIX/MATRIX bus by using the Bank
Select keys and the [SEL] keys in the Centralogic section.
If you select the MIX buses or MATRIX buses by pressing
the [SEL] keys, the setting of the MIX/MTRX ON FADER
switch button will be changed automatically.
• If you press the currently-selected MIX/MATRIX bus select
button again, cue monitoring will be turned on for the
related MIX/MATRIX channel. This method is convenient if
you want to monitor the signal that is being sent to the
selected MIX/MATRIX bus.
4.
Use the faders in the INPUT section to adjust
the send level from the input channels to the
selected MIX/MATRIX bus.
NOTE
You can assign the SENDS ON FADER function to a USER
DEFINED key. This lets you quickly switch to SENDS ON
FADER mode for a specific MIX/MATRIX bus, and quickly
switch back again.
5.
Repeat steps 3–4 to adjust the send level for
other MIX/MATRIX buses in the same way.
6.
When you have finished adjusting the
MIX/MATRIX send levels, press the X symbol
in the function access area.
The function access area display will return to its prior
state, and the unit will return to normal mode.