Returning to the default screen ............................15 Learning a code Before starting, read the following tips ..........................16 Instructions for downloading keys ............................17 To clear all the keys downloaded in a given mode ......................17 Other functions Beep........................................18 Backlighting ......................................18 Zero reset ......................................18 Scanning the channels ..................................18...
• Do not let children use the remote control alone. • Your ROC 850 remote control is designed for domestic use, and not industrial use. It must be used within a family and private environment. • Any dismounting or modification of this remote control cancel your rights to the guarantee.
Your remote control is fitted with an LCD (Liquid Crystal Display) touch screen.This screen displays a keypad, with virtual keys you can use when programming or controlling a device. In this manual, the touch screen keys are designated LCD keys, whereas the other keys (actual keys) are designated keypad keys.
(polarity). • Do not leave the batteries in the remote control if you intend no to use it for a long period of time. Used batteries can leak an acid liquid.This liquid can damage the remote control and is toxic: it burns the skin and the mucous.
About your remote control Description of keys and LED : lights up briefly whenever used (pressing a key or the touch screen). Indicates the transmission of a command. Blinks 3 times in case of mistake. : operating mode keys, used to select the AUDIO device to control.
) or one of the MODE keys ( ) on the keypad, or any area of the LCD screen.The other keys on the keypad do not activate the LCD screen.The keys common to all the modes are described below. Select a channel number or enter the number of the device to Keys 0 to 9 control.
Displays the channel number, program title... Select the SP or LP modes on certain VCRs (simple play or long play function). To open the disc tray or to eject a cassette. Access to the ShowView or VideoPlus+ function on certain VCRs (see page 19).
). If the device switches off, this means the code entered is correct. All you need to do is check the various keys on the touch screen, in order to determine whether the keys proposed on the screen can be used to control the device concerned.
If touch keys are inoperative, reprogram using make scanning, by restarting the procedure. • When all the codes for a make have been tested, the red indicator blinks 3 times to indicate scanning is complete, and the main screen displays.
Note: this method presumes you wish to memorize a VCR code under the VCR mode, a satellite receiver code under the CBL mode, etc …To memorize, for example, a VCR code under the CBL or other code, the CBL mode key must be dedicated to the list of VCR codes.You can assign any VCR code under the CBL mode, by applying the method described in page 8, before scanning.
MODE control.The next screen appears (CODE screen). Press the ) key.The 3 digits of the code memorized appear SETUP one after the other.The main screen displays. Identification of the code is completed. Press the key on the touch screen. EXIT...
20 instructions. Once memorized, press the ) key and the touch MACRO screen key for the sequence to run. Before programming, take a few minutes to write down the sequence to compose.This will be particularly useful to achieve your programming and use it later.
Inside a sequence, the time between 2 infrared transmissions is 0.5 seconds. You may have to increase this time in order to leave, for example, the time for the TV to light on and display the images of a channel.
SETUP keys. P<P Enter the first number of one of your 2 favorite channels (1 to 3 digits). If your channel has less than 3 digits, press the mode key ( , …) after entering the number.
Maintain the key of the mode to restore depressed. The main screen displays, press EXIT to quit. Note: to cancel your screen customization and return to the default screen, press the Mode key and hold it during about 3 seconds (until the main screen appears). The SLEEP SETUP...
Learning a code To recover all the features of one of your original remote controls (e.g. the one supplied with your TV set), you can download the infrared codes from the original remote control into your ROC 850.Your ROC 850 can “copy” up to 40 keys per mode.
ROC 850 blinks once and the LEARN NEXT screen appears (this can take 2 to 3 seconds). In case of error, the red indicator blinks during 3 seconds, but the ROC 850 remains in the learning mode with the LEARN NEXT screen displayed.To download a new key, press...
Other functions Beep A beep can be generated when pressing the keys. If you wish to remove this feature, you can disable it and reactivate it later. Activate the touch screen by pressing it. Press the ) key until the red indicator remains lit (2-3 SETUP seconds) and the display of the next screen (Setting screen).
. General Off This function is used to switch off all the devices by pressing on a single key. Press promptly (in less than a second) twice on the B key and hold the key the second time.
• Check that the original remote control of the device you wish to control is operating properly. • If the list of codes you chose in programming (page 8) is inoperative, try the next code or use automatic scan programming (page 10).