Mitsubishi FREQROL FR-A024-0.1K Instruction Manual page 161

APPENDICES
Appendix
1.
WTRUCTIOMS FOR COMPLIANCE WITH THE EUROPEAN DIRECTIVES
(LVD
compliant product har
CE marking.)
1.
EMC
DIRECTIVE
Our view
d
inverters for the EMC Dirsctve
An inverter does not
hndbn
m d e n t l y .
lt b
a compoMnt
designed
for installation
in
a cantrol
box and tor
use with
anomer
eguipmenl
to
mtrd
a machin, or egupment. Therobre, we do not
think that the EMC Directive
applies
directly to Invecters. F w
Mls
r - ,
we do
nol p&w a CE mark
on the inverter. CE mark placed on the inverter shows compliance to the Low Vokage Diredive. The
European power drive manufacturers' organization (CEMEP) also
h o b t h i s p O m l of
view.
We
do not
think that the inverters themselves are covered directiy t y
(he
EMC Directive. However,
the EMC Directive applies
(0
machines and
equipment
into which hv&n have teen incorporated,
and these m a c h e s and Sgupnent mudt cany the CE mark.
H e n c e ,
we haw prepared a technical
document 'EMC
Installation
Guidelines' (manual number BCN.A21041-202)
bo
that machines and
equipment
lncorporatlng inverters may conform to the EMC D i m c t h more
easibj.
Outline of installation method
It
is recommended to install an inverter in the following method:
Y
Use
the inverter with an European Standard-compliant noise filter.
#
For wiring between the inverter and motor, use shielded
c a b l e s
or run caMes in metal conduit
and ground the
c a k s
or conduit at the inverter and motor ends
Use the short& possble
cable
Y
install the inverter in an grounded metal enclosure. The endosure should prevent
d i e d
noise
#
I n s a r t
a
l i n e noise f i n e r
and ferrite core into
the
power and contrd
l i
are required.
Full information including the European Standard-compliant nobe filler specificatiw are pubiished
in the
'EMC
Installation Guidelines' (manual number BCN-A21041-202). Please contact your sales
representative.
C o m p l W e
W W
leakage.
2.
Low
Voltage Directive
Our view of inverters
f o r
the Low Voltage Directive
Inverter are covered by the Low Voltage Directive.
C O m p l i a n C e
We
M a r e we meet Low Voltage Directive and place CE
marcOng on
the mverter.
The European verikation institution has approved that our inverters conform to DIN VDE01W.
Instwions
To conform
to
DIN VDEOl60, the following specifications and instructions listed are dinerent from
those of the standard models.
In the 400V class inverters, the rated input voltage range
is
%phase, W V to 415V, 50/60Hz.
Do
not use residual current device as the only protection against indirect contact. Protective
earth connection is essential.
Wire the earth terminal independently.
(Do
not cmnect two or more
cables.)
Only use EN or IEC compliant no-fuse breaker and magnetic contractor.
Use
the inverter under condition
of
Over Voltage Category
It
and Pollution Degree
2
or better.
0
Insert an EN or IEC Standardcompliant isolation transformer or surge suppresser
to
make
0
Install in a cabinet with IP54 rating or better to have Pollution Degree
2.
For the
input
and output
of
the inverter, only use cables
of
the type and size bet forth
in
EN60204
Appendix C.
The rating of the alarm output relay is 30V DC. 0.3A. There is basic insulation between the a!am
output relay and the inverter control circuit
the Over Voltage Category
II
if power supply over vollage category
is 111 c f
IV.
-
APP
.
1
-