Related Manuals for True Induction TI-1+1B
Summary of Contents for True Induction TI-1+1B
- Page 1 true INDUCTION� COOKTOP MANUAL For the Following Models Tl-1 + 1 B Tl-1 +2B Tl-1 + 1 GT Tl-1 +2GT Tl-2GT Tl-3GT iwx. Visit Us: www.Truelnduction.com Call Us: 877-862-7049 INDUCTION...
-
Page 2: Important Safety Information
WARNING: Gas leaks cannot always be detected by smell. Gas suppliers and True Induction recommend that you use a gas detector approved by UL or CSA. If a gas leak is detected, follow the 'What to do if you smell gas" instructions above. - Page 3 IMPORTANT SAFETY INFORMATION Continued WARNING: To reduce the risk of fire, electrical shock, injury to persons, or damage when using cooktop, follow basic precautions including the following: WARNING: NEVER use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the cooktop.
- Page 4 TRUE INDUCTION Models Tl-1+1B Tl-1+2B Tl-1+1GT Tl-1+2GT Tl-2GT Tl-3GT INDUCTION...
-
Page 5: Unit Diagram
UNIT DIAGRAM Tl-1+1B & Tl-1+2B 1. Cooking Zone 2. Ceramic Glass 3. Control Panel 4. Lower Power Key Raise Power Key Heat/Temperature Key Lock Control Key 8. Timer Key Power Button 10. Control Knob 11. Gas Burner 1. Cooking Zone 2. - Page 6 UNIT DIAGRAM Tl-1+1GT & Tl-1+2GT 1. Cooking Zone 2. Ceramic Glass 3. Control Panel 4. Lower Power Key Raise Power Key Heat/Temperature Key Lock Control Key 8. Timer Key Power Button 10. Control Knob 11. Gas Burner 1. Cooking Zone 2.
- Page 7 UNIT DIAGRAM Tl-2GT & Tl-3GT 1 . Gas Burner 1 2. Gas Burner 2 3. Left Control Knob 4. Right Control Knob 1 . Gas Burner 1 2. Gas Burner 2 3. Gas Burner 3 4. Left Control Knob 5. Middle Control Knob 6.
-
Page 8: Unit Measurements
UNIT MEASUREMENTS Specifications Tl-1+18 Tl-1+28 1750 Watts 1750 Watts POWER 120v / 60Hz I 12V DC Ignition 120v / 60Hz I 12V DC Ignition VOLTAGE 6500 6500, 8200 150F - 450F 150F - 450F TEMP. RANGE 1 - 10 1 - 10 LEVEL SELECTION MATERIAL Frame: Stainless Steel I Induction: Ceramic Glass... -
Page 9: Installation
Space ..,.._ connections INSTALLATION Beginning Installation • Installation and service must be conducted by qualified / licensed technician, in accordance with national & local regulation. Failure to comply will void the product warranty. • Always disconnect the appliance power before installation & maintenance. •Shut off the main gas supply valve before disconnecting the old cooktop and leave it off until the new hook-up has been completed. - Page 10 INSTALLATION Clearance for Cooktops � � A: Minimum distance is *26" B: Minimum vertical of side cabinet is 18" C: Minimum distance is 1" D: Minimum side wall clearance is 6" E: Minimum rear wall clearance is 2" *For RV applications: Cooktops are designed for specific applications. As such, clearances will vary significantly.
- Page 11 INSTALLATION Cutout Sizes FOR UNITS: Tl-1+1B Tl+1+1GT Tl-2GT FOR UNITS: Tl-1+2B Tl-1+2GT Tl-2GT INDUCTION...
- Page 12 INSTALLATION Fastening the Cooktop • Please use the "cutting size board" (cardboard packed in the box) to outline and cut a hole in the counter top. • Remove burners and grids. • Turn the cooktop over and rest the top side on a cloth. •...
- Page 13 G�SPRESUREREGULATOR (SUPPLIED) ARRO\V TO\VAR D COOKTOP � GAS SHUT INSTALLATION Connecting the Gas • Shut off the main gas supply valve before disconnecting the old cooktop and leave it off until the new hook-up has been completed. Don't forget to relight the pilot on other gas appliances when you turn the gas back on.
- Page 14 INSTALLATION Install Burner Heads • Ensure the tabs on burner head are aligned and inserted into notch of the burner base on cooktop. Assemble center burner, when used as shown in Fig-6. • Grate is set by positioning the legs on the burner base holder. •...
-
Page 15: Unit Battery
INSTALLATION Unit Battery Units may feature with low voltage connection or electric adapter for the electric gas igniter. 12 Volt DC Wire Connection • Hook the 12 Volt Positive to RED Lead • Hook the 12 Volt Negative to the BLACK Lead Connect the Electric Adaption Insert DC plug into DC terminal on the bottom plate (see Fig. -
Page 16: Gas Information
INSTALLATION Gas Information Converting to LP Gas T his cooktop leaves the factory set for use with LP gas. Please read the rating label information carefully to confirm this. Provide Adequate Gas Supply • Your cooktop is designed for LP gas (propane), 1 O" of water column. •... - Page 17 INSTALLATION Gas Information Adapting the Cooktop for Different Types of Gas To adapt the cooktop to a different type of gas than that for which it was designed, (see the sticker under the hob or on the package), the burner nozzles must be changed as follows: •...
- Page 18 INSTALLATION Gas Information When switching from one type of gas to another, the minimum flow rate must be adjusted so the flame should not go out. To regulate the flame follow the following steps: • Light up the burner • Turn the knob to minimum level •...
- Page 19 INSTALLATION Gas Information When all connections have been made, make sure all cooktop controls are in the off position and turn on the main gas supply valve. Use a liquid leak detector at all joints and connections to check for leaks in the system. GAS BURNERS Gas flow to the burners is adjusted by turning the knobs which control the valves.
- Page 20 INSTALLATION Gas Information Other intermediate operating adjustments can be achieved by positioning the indicator between the HI and LOW positions and never between the HI and OFF position . • When the range is not being used, set the gas knobs to their OFF positions and also close the gas shut-off valve placed on the main gas supply line .
- Page 21 INSTALLATION Gas Information • Any film or stickers on the cooktop surface should be removed before use. • All operations are performed by means of all control knobs. Knob controls electric ignition, safety device & flame level. • TO IGNITE- push and turn the knob for 1-2 seconds in a counterclockwise direction up to the HI position (Maximum rate), push in and hold the knob until the flame has been lit.
- Page 22 INSTALLATION Gas Information Check operation of electric igniters. Check flame characteristics. Flame should be blue with NO yellow tip. Yellow flames: Further adjustments are required. Yellow Tips on OuterCones Normal for LP Gas. Soft Blue Flames: Normal for Natural Gas. If the flame is completely or mostly yellow, verify that the regulator is set to the correct fuel.
- Page 23 INSTALLATION Gas Information For greater efficiency and lesser gas consumption, use the pots and pans with the right diameters of the burners. Avoid having flames extending out from underneath the pans (refer to the table). A smaller diameter pot or pan placed on a larger burner does not necessarily mean that the boiling conditions are reached quicker.
- Page 24 INSTALLATION Gas Information During a power failure the burners will not light automatically. In an emergency, a cooktop burner may be lit with a match by following the steps below. WARNING: Lighting gas burners with a match is dangerous. You should match light the cooktop burners only in an emergency.
-
Page 25: Using The Cooktop
USING THE COOKTOP Unit Functions Using the Induction Cooktop portion of your unit • Plug the power plug into a standard outlet. • The Power button will light up and the unit will sound to indicate on. • The device will remain in standby mode, awaiting user direction. •... - Page 26 • You can also change the HEAT or TEMP settings without affecting the current timer setting. Built-In Safety Shut Off • The True Induction cooktop is designed to automatically shut off after 150 minutes of use. This built-in auto shut off is a safety feature.
-
Page 27: Compatible Cookware
Shake your cookware, if your magnet stays, then your cookware is ready to be used on the True Induction cooktop. Optimal cookware has a flat bottom and a diameter of 4.5 - 10 inches. Round, flat bottom pans give the best results. -
Page 28: Cleaning And Maintenance
CLEANING AND MAINTENANCE Unit Care IMPORTANT: Before any operation of cleaning and maintenance, disconnect the appliance from the electrical supply. It's required to clean when the appliance has cooled. • Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the surfaces. •... -
Page 29: Troubleshooting
TROUBLESHOOTING Error Messages IMPORTANT: Before any operation of cleaning and maintenance, disconnect the appliance from the electrical supply. It's advisable to clean when the appliance has cooled, especially for cleaning the enameled parts. INDUCTION... - Page 30 TROUBLESHOOTING FAQ - Induction Portion It may occur that the cooktop does not function or does not function properly. Before calling customer service for assistance, lets see what can be done. First of all, check to see that there are no interruptions in the gas and electrical supplies and, in particular, that the gas valves for the mains are open.
- Page 31 TROUBLESHOOTING FAQ - Gas Portion It may occur that the cooktop does not function, or does not function properly. Before calling customer service for assistance, lets see what can be done. First, check to see that there are no interruptions in the gas and electrical supplies, and, in particular, that the gas valves for the mains are open.
-
Page 32: Safety Information
When using electrical appliances, basic safety precautions should always be followed. For the True Induction cooker, it is essential to heed all precautions: • When the unit is on, do not touch outside the control panel as the surface may contain residual heat. - Page 33 SAFETY INFORMATION • T his appliance has a polarize plug (one blade is wider than the other). To reduce the risk of electric shock, the plug will fit on the outlet only one way. If the prongs do not fit fully, reverse the plug.