Page 2
STATEMENT OF LIMITED WARRANTY The Eastwood Company (hereinafter “Eastwood”) warrants to the end user (purchaser) of all new welding and cutting equipment (collectively called the “products”) that it will be free of defects in workmanship and material. This warranty is void if the equipment has been subjected to improper installation, improper care or abnormal operations.
OVERLOAD PROTECTION The Eastwood Versa-Cut 40 CNC Plasma Cutter is equipped with an overload protection. This device will protect the plasma cutter if the duty cycle is exceeded. If the output is exceeded, the breaker will trip, the AMBER Overtemp Indicator will illuminate and cut off the power supply to the torch although the fan will still run to cool the unit.
Page 5
• Use an OSHA approved respirator when plasma cutting in confined spaces or where there is inadequate ventilation. • Use extreme caution when plasma cutting coated materials including but not limited to: cadmium plated, galvanized, lead based paints, powder coat. To order parts and supplies: 800.343.9353 >> eastwood.com...
Page 6
• Plasma cutting heats metal and tools to temperatures that will cause severe burns! • Use protective, heat resistant gloves and clothing when using Eastwood or any other plasma cutting equipment. Never touch a cut work surface, torch tip or nozzle until they have completely cooled.
NEMA 6-50R receptacle. If unsure about your electrical setup contact a licensed electrician. As an alternative, by using the included Adapter Cord, the Versa-Cut 40 CNC can be used with a 120 VAC, 20 AMP grounded NEMA 5-15R outlet protected by a circuit breaker.
Page 8
CUT 40 CNC SET-UP FIG. 3 FIG. 3 The Eastwood Versa-Cut 40 CNC Plasma Cutter is factory set-up for plasma cutting any material and thickness after the connections are attached. INSTALLING THE GROUND CABLE AND CLAMP • Locate the 10 ft. Ground Cable/Clamp Assembly [B] and connect the plug on the brass end to the Negative Ground Cable Connection (–) on the Plasma Cutter...
Page 9
FIG. 5 FIG. 5 Included with the Versa-Cut 40 CNC is the Plasma Cutter to CNC Table Cable 10’ [3m] [D]. This cable plugs into the 12-Pin CNC Control Connection [d] and allows for direct connection to Eastwood Versa-Cut 4’x 4’ CNC Plasma Tables.
Page 10
• Push the adjustment knob back in to lock it. The air pressure is adjusted correctly. PLASMA CUTTING MODES The Eastwood Versa-Cut 40 CNC Plasma Cutter has multiple trigger modes to select from utilizing the Plasma Cutting Mode Button [5]. Find the best mode for your project by reading the descriptions below.
Page 11
This minimizes the cleanup of the edge with a grinder or file. Another excellent technique is to practice plasma cutting your initials out of a piece of steel. Versa-Cut 40 CNC Plasma Cutter - Air Pressure and Amperage Settings* Metal Thickness 1/32”...
Page 12
(commonly know as an edge start) reduces wear and risk of damage. DO NOT attempt to cut thicker material than 3/8” when hand cutting or CNC plasma cutting. 90° 90° Eastwood Technical Assistance: 800.343.9353 >> tech@eastwood.com...
TORCH MAINTENANCE The Eastwood Versa-Cut 40 CNC Plasma Cutter torches have several consumable parts that will need to be replaced over time. If wear or slag build up is noticed on any of the torch components, replace them immediately to avoid damage to the torch. Worn components will also contribute to poor plasma cutting and difficult arc starting.
20 Amp circuit 240±10% Volt AC, minimum 50 Amp circuit. Supply Air Pressure Too Low to Support Check air supply pressure. Do not attempt to operate the Versa-Cut 40 CNC Plasma Arc below 60 psi while air is flowing.
Page 15
Check that the ground clamp is properly positioned, and a good ground is Poor Ground Connection on Workpiece established on clean bare metal of workpiece. Install an effective moisture separator in the air supply to the Versa-Cut 40 CNC Excessive Moisture in the Air Supply such as the #31633.
Page 16
Check air supply pressure. Do not attempt to operate the Versa-Cut 40 CNC Plasma Arc. below 60 psi while air is flowing. Do not attempt to exceed the cutting thickness capability of the Versa-Cut 40 CNC: Maximum Recommended Material 120VAC: 1/8”...
Page 17
NOTES To order parts and supplies: 800.343.9353 >> eastwood.com...