Table of Contents
Advertisement
1) Press the EQ button [14] to go to the equaliz-
er mode.
2) Press the BAND button
to select EQ
BASIC or EQ USER.
Each time you press the BAND button [8], the
EQ BASIC and EQ USER toggles.
- EQ BASIC: This menu consists of the 6 equal-
izer characteristics initially set.
EQ USER:
The
menu
containing
user-set
equalizer characteristics (for set-
ting the characteristics, see the
next subsection
"Setting
and
storing the equalizer characteris-
tics". The equalizer No. where no
setting is made becomes flat.)
3) Press No. 1 to 6 of the Preset buttons [9] io
select the equalizer characteristic to be set.
No.1
| BAS
Bass is
US1
(BASS BOOST)
emphasized.
No.2
|HIG
Treble is
US2
(HIGH BOOST)
emphasized.
No.3
{ACO
Mean (human
US3
(ACOUSTICAL)
voice) is
emphasized.
IMP(IMPACT)
Bass and
US4
treble are
emphasized.
US5
US6
SMO
Sound level of
(SMOOTH)
each band is
smoothed.
FLA(FLAT)
Original sound
(flat equalizing)
Note:
e Turn on the equalizer effect after following the
instructions in the next subsection "Turning on and
off the equalizer effect". Otherwise, the above set-
tings will be invalidated.
Turning on and off the equalizer effect
1) Press the ADJ button [15] to go to the CON-
FIGURATION
mode.
2) Slide the o-selector [1] to W (down) or A
(up) to move the cursor to "EQ".
3) Slide the o-selector [4] to
(right) to turn
"OFF" and "ON".
4) Press the ADJ button [15] to return to the pre-
vious mode.
Operating the DSP and Equalizer
Setting and storing the equalizer
characteristics
You can set your own equalizer characteristics
and store them to "EQ USER' (US1 to US6). Up
to 6 patterns can be stored.
Notes:
e This setting cannot be edited when EQ in the
CONFIGURATION display is turned off.
e /f the control is idle for about 5 seconds after each
operation, the unit returns to the previous mode.
1) Press the EQ button [14] to go to the equaliz-
er mode.
2) Press the BAND button
to select "EQ
USER".
3) Press ENT of the a-selector [1] when the "EQ
USER' is displayed.
4) Slide the a-selector [1] to <q (left) or > (right)
to select the frequency and slide to A (up) or
'WV (down) to adjust the sound level.
* Repeat the above procedures to set the char-
acteristics.
* The frequency selection option differs accord-
ing to the connection unit as follows:
Sound level to
DSP/EQ | Frequency to be
|
type
selected
be adjusted
DPH9300 | 30/50Hz, 100Hz,
—12dB to +12dB
DPH7300 | 200Hz, 400Hz,
1kHz, 3kHz, 12kHz
30Hz, 60Hz, 120Hz, | —15dB to +15dB
200Hz
EQH5100
.
400Hz, 1kHz, 3kHz,
| -12dB to +12dB
8kHz, 12kHz
5) After setting the characteristics, press and
hold one of the Preset buttons [9] (No. 1 to
No. 6) where you want to store the setting.
A beep sounds when the setting is stored.
6) Press the EQ button [14] to return to the previ-
ous mode.
Other equalizer settings
Basic settings
The following items can be set for the equalizer.
¢ No. of sub woofers: STEREO/MONO/OFF
(SUB WOOFER: when sub woofers are connected)
¢ Lowest frequency: 30 Hz/50 Hz
(EQ MINFREQ: when the DPH9300 or DPH7300
is connected)
¢ Parametric equalizer adjustment: FRONT/REAR /OFF
(P. EQ: when the DPH9300 is connected)
¢ Turning on and off the surround effect: ON/OFF
(SURROUND: when the EQH5100 is connected)
VRAX8370A
37
Advertisement
Table of Contents
