Carrier SmartVu 61AF 030-105 Manual page 16

5 - USER INTERFACE: MENU STRUCTURE
PRESSURE – Pressure
No. Name Status
1 DP_A -
2 SP_A -
3 ECO_SP_A -
4
5
6 W_P_IN -
*Depends on the selected language (English by default).
SETPOINT – Setpoint
No. Name Status
26.7 to 65.0
1 hsp1
80.0 to 149.0
26.7 to 65.0
2 hsp2
80.0 to 149.0
0.1 to 1.1
3 hramp_sp
0.2 to 2.0
4 lim_sp1 0 to 100
*Depends on the selected language (English by default).
INPUTS – Inputs
No. Name Status
1 ONOFF_SW open/close
2 SETP_SW open/close
3 LIM_SW open/close
4 LIM_ANAL -
5 FLOW_SW open/close
6 HP_SW_A open/close
7 DHW_REQ open/close
8 FDBK_A1 open/close
9 FDBK_A2 open/close
*Depends on the selected language (English by default).
OUTPUTS – Outputs
No. Name Status
1 CP_A1 off/on
2 CP_A2 off/on
3 FAN_A1LS off/on
4 FAN_A1HS off/on
5 FAN_A2LS off/on
6 FAN_A2HS off/on
7 EXV_A -
8 EXV_ECO -
9 EV_VALV1 off / on
10 EV_VALV2 off / on
11 RV_A off/on
12 EXCH_HTR off / on
13 BOILER off / on
14 EHS_STEP 0 to 4
16
Unit Displayed text*
kPa/PSI Discharge Pressure
kPa/PSI Main Suction Pressure
kPa/PSI Eco. Suction Pressure
INTERNAL HYDRONIC MODULE Internal hydronic module
kPa/PSI Inlet Water Pressure
Default Unit Displayed text*
65.0 °C
Heating Setpoint 1
149.0 °F
65.0 °C
Heating Setpoint 2
149.0 °F
0.5 ^C
Heating Ramp Loading
1.0 ^F
100 % Switch Limit Setpoint
Unit Displayed text*
- Remote On/Off Switch
- Remote Setpoint Switch
- Limit Switch
mA Limit Analog Input
- Flow Switch
- HP Switch Circuit A
- DHW Tank Request
- CPA1 Safety FeedBack
- CPA2 Safety FeedBack
Unit Displayed text*
- Compressor A1 Output
- Compressor A2 Output
- Fan A1LS Output
- Fan A1HS Output
- Fan A2LS Output
- Fan A2HS Output
% Main EXV Position
% Economizer EXV Position
- ECO/CPA1 Isolation Valve
- ECO/CPA2 Isolation Valve
- 4 Way Refrigerant ValveA
- Exchangers Heaters
- Boiler Command
- Electrical Heat Stage
Description
Compressor discharge pressure
Compressor suction pressure
Economizer suction pressure
Inlet water pressure
Description
Heating setpoint 1 (used during occupied periods)
Heating setpoint 2 (used during unoccupied periods)
Ramp loading setpoint (rate at which the water temperature may
change within one minute)
Setpoint used for capacity limitation
Description
Remote On/Off switch
Remote setpoint switch:
open = setpoint 1
closed = setpoint 2
Demand limit switch
Limit Analog Input 4-20mA
Water exchanger flow switch
High pressure switch, circuit A
Domestic hot water tank request
Compressor A1 safety feedback
(open contact = compressor is stopped)
Compressor A2 safety feedback
(open contact = compressor is stopped)
Description
Compressor A1 status
Compressor A2 status
Fan A1 low speed status
Fan A1 high speed status
Fan A2 low speed status
Fan A2 high speed status
Main EXV position
Economizer EXV position
Economizer / compressor A1 isolation valve
Economizer / compressor A2 isolation valve
4-way refrigerant valve, circuit A: Used to manage cooling /
heating / defrost operation (heat pumps)
Exchanger heater status (used to protect the water
exchanger against freezing in case of low OAT)
Boiler command
Electrical heating stage