Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BEMIS bioBidet SLIM TWO
Summary of Contents for BEMIS bioBidet SLIM TWO
-
Page 2: Product Information
PRODUCT INFORMATION Important Safeguards Overview & Parts Wireless Remote Registration and Installation Resources GETTING STARTED Functions & Features INSTALLATION Installation Guide Questions? We’re here to help. MAINTENANCE 847.458.2334 Cleaning the Slim Two support@biobidet.com Draining the Water Tank www.biobidet.com Troubleshooting Guide Specifications Technical support and alternate fittings are available. - Page 3 PLEASE OBSERVE THE FOLLOWING PRECAUTIONS AND INSTRUCTIONS BEFORE INSTALLATION AND USE. • This product must be connected to a grounded 120V GFCI (ground fault circuit interrupt) outlet. Do not connect the power cord if it is damaged or broken. Do not plug the product into a loose electrical outlet. •...
- Page 4 Slim Two Slim Two Parts List Power Cord (4ft) T-Valve Top Mount Washers Bolt Guides Rubber Nuts *Rubber Washer Inside Side Control Panel Night Light Mounting Bolts Bidet Hose Catch Plate Heated Seat Seat Sensor Nozzle 2 AA Wireless Remote Mounting Batteries Remote Bracket...
-
Page 5: Functions And Features
Functions & Features Stop/Reset Button The Slim Two is a bidet toilet seat designed for superior hygiene, comfort, and sustainability. Each use will leave you Rear Wash feeling clean and confident, while reducing your overall eco footprint. Front Wash Sit Down On The Seat Turbo Wash This product includes a built-in seat sensor that must be activated with skin contact in order to operate bidet functions. - Page 6 Child Wash Nozzle Cleaning Press to activate a child-friendly wash with low water pressure. While not seated, press “Nozzle Cleaning” to extend the nozzle for Press again to oscillate. three cycles of automatic cleaning. Afterwards, the nozzle will remain extended for manual cleaning without spraying. Press the “Stop”...
- Page 7 3. Install Catch Plate BEFORE INSTALLATION Place the catch plate and bolt guides over the mounting holes. Insert the mounting bolts through the washers, guides, catch plate, and top mount rubber nuts into the Do not plug the power cord in until installation is complete. mounting holes.
-
Page 8: Installing The Remote
5. Connect the Water Hoses Install the t-valve onto the toilet tank. Ensure the rubber washer is properly seated inside the t-valve. Connect your existing toilet hose to the water shut-off valve and t-valve. Toilet Tank Connect the provided bidet hose to the bidet seat and t-valve. Open the water shut-off valve. -
Page 9: Cleaning The Strainer
Cleaning the Strainer Draining the Water Tank Before draining, unplug the power cord and wait 30 minutes until the unit has cooled down. Do not insert your finger into the drain hole. *Close shut-off valve *Close shut-off valve This product will not operate properly if the strainer is clogged. Please clean the strainer regularly. - Page 10 Specifications Slim Two Problem Solution Rated Voltage 120V, 60Hz Max. Power Consumption • Check if the power 870W plug is connected Completely out of order Reccomended Water Inlet Pressure 9.9~106.6 psi • Check if the power supply Power Cord or outlet has failed 4 feet Wash Wash...
- Page 11 1 YEAR FULL COVERAGE WARRANTY This warranty gives you specific legal rights. You may have other rights which vary from state to state. To obtain warranty repair service under this warranty, you must contact Bio Bidet Innovation LLC or an authorized distributor. Bio Bidet Innovation LLC warrants its product to be free from manufacturing defects under normal use and service for a period of one (1) year from This written warranty is the only warranty made by Bio Bidet Innovation LLC.
- Page 12 Notes...
- Page 13 Customer Support T: 847.458.2334 TOLL-FREE: 877.339.5214 7900 S IL Route 31 Crystal Lake, IL 60014 support@biobidet.com www.biobidet.com...