Related Manuals for Hyundai HSO20305-1
Summary of Contents for Hyundai HSO20305-1
- Page 1 RADIAL DUAL SLIDE MITER SAW HSO20305-1 WARNING: PLEASE READ THE MANUAL CAREFULLY BEFORE USING THE UNIT!
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS 2. TECHNICAL DATA 3. DESCRIPTION 4. USE 5. MAINTENANCE AND STORAGE 6. TROUBLESHOOTING 7. DISPOSAL 8. WARRANTY 9. DECLARATION OF CONFORMITY Year of fabrication: 2020... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS General power tool safety warnings WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool"... - Page 4 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
- Page 5 h) Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of wood or other objects that contact the revolving blade can be thrown with high speed. i) Cut only one workpiece at a time.
- Page 6 Use only blades recommended by the manufacturer that comply with EN847-1. Do not use high speed steel blades (HSS blades). If the plate inserted on the swivel table is worn or damaged, have it replaced by an authorized service center Objects such as cloth, strings, should never be left in the working zone.
- Page 7 Always check if the saw blade guard is working properly. It shall be well assembled, and it shall be easily moving with hand and that it can be locked when operating the tool (see in instructions for use). Laser safety instructions Warning: Do not look directly at the laser beam.
- Page 8 Attach the miter saw to a workbench if possible. When cutting a long piece that extends far beyond the width of the table, supports must be used to support the ends of the workpiece at the same height as the cutting table. The supports must be positioned so that the workpiece does not fall to the ground when the cutting has finished.
-
Page 9: Technical Data
2. TECHNICAL DATA Model HSO20305-1 Mains voltage/ frequency 230-240 V˜ 50 Hz Power 2000W Speed 4350/min Type Single Phase Blade size Ø305 x Ø 30 x 40TX2.8 mm Tilting swing arm 45° G/D Swivel base 45° G/D Sound pressure level LpA 94.6 dB(A) -
Page 10: Description
3. DESCRIPTION 1. Trigger lock 2. Handle 3. Trigger 4. Stopper 5. Side extensions 6. Locking screw for the saw table 7. Graduation scale 8. Blade protection 9. Saw blade 10. Laser 11. Blade slide 12. Swivel table 13. Carrying handle 14. - Page 11 4. UTILISATION Intended use This mitre saw should only be used for to cut rafters, baseboards, panelling, wooden floors, boards, or cutting pieces of aluminium, processed wood or similar materials. Caution, do not use the machine beyond the maximum capacity provided and do not cut branches, logs and any other material with presenting risks of ignition, explosion or release of pollutant or dangerous for the user or the environment Any other use, different from that provided in these instructions, may cause damage to the device and...
- Page 12 WARNING! Unplug the machine before any intervention. a) Unlock and lock the saw head During transport, handling or storage, the saw head should be folded and locked in this position. To unlock the saw head, exercise a downward pressure on the handle and pull out the locking pin located at the rear of the machine, so the head can return to its proper operating position.
- Page 13 d) Connection of the dust and chips collector bag Insert the dust bag over the extraction outlet located at the rear of the machine. You can also connect a vacuum hose to the dust extraction bend to improve suction. The dust bag should be emptied frequently. The dust bag is equipped with a zipper to empty it more easily.
- Page 14 - Push with your thumb on the locking device of the lower blade guard so that the blade guard covers the blade. - Tighten the housing screw of the blade bolt. - Check the locking device of the lower blade guard is properly in place and that it properly blocks the latter.
- Page 15 i) Use of the stop: Your mitre saw is equipped with a fixed part stop as well as removable stop, on the right and left side: they allow immobilizing the workpiece during the cutting operation and thus prevent it from moving. You should always push the workpiece against the latter, regardless of the type of cut to be performed.
-
Page 16: Use
k) Start-up The base of your saw should be placed and well fixed on a solid, flat surface in a place inaccessible to children. Ensure the proper tightening of the safety components and blade before starting. Connect the machine to the 230V mains. To turn the saw on, press the locking device and then press the trigger switch. - Page 17 3. Rotate the table until the indicator reaches the desired angle on the scale tab 4. Secure the tab lock lever. 5. Before turning the saw on, run a test on the idle machine to make sure that the cutting is not difficult. 6.
- Page 18 Bias cuts are performed with the table positioned on the tab 0° and the blade tilted at an angle between 0° and 45°. - Rotate the table so that the indicator shows 0° on the scale tab. - Lock the table by blocking the locking lever. - Loosen the tilt locking knob and tilt the blade motor block to the left or right up to the desired angle.
-
Page 19: Maintenance And Storage
The angles for crown mouldings are very precise and difficult to adjust. Given that the angles tend to go out of adjustment, all settings should first be tested on scrap mouldings. In addition, most walls are not exactly perpendicular, so adjustments should be made accordingly. 5. -
Page 20: Troubleshooting
3. Protect it from direct light. If possible, store it in the dark. 4. Do not lock it nylon bags as moisture could form. 6. TROUBLESHOOTING PROBLEMS POSSIBLE CAUSES SOLUTIONS The motor does not start 1. Under voltage Check the connections and the 2. - Page 21 8. EXPLOSED VIEW...
-
Page 22: Declaration Of Conformity
Phone: +33 (0) 5.34.508.508 Fax: +33 (0) 5.34.508.509 Declares that the machinery designated below: RADIAL DUAL SLIDE MITER SAW HSO20305-1 Serial number: 20200806945-20200807184 Complies with the provisions of the Directive “Machinery” 2006/42/EC and national laws transposing it: Also complies with the following European directives:... - Page 23 10. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor.
- Page 24 11. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine.
- Page 25 12. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...