Related Manuals for Hyundai HSC20V2A
Summary of Contents for Hyundai HSC20V2A
- Page 1 CORDLESS CIRCULAR SAW HSC20V2A WARNING: Read thoroughly the instruction manual before use...
-
Page 2: Table Of Contents
CONTENTS 1. INTENDED USE 2. SAFETY INSTRUCTIONS 3. YOUR PRODUCT 4. SPECIFICATIONS 5. ASSEMBLY 6. OPERATION 7. CLEANING, MAINTENANCE AND STORAGE 8. TROUBLESHOOTING 9. DISPOSAL 10. DECLARATION OF CONFORMITY 11. WARRANTY 12. PRODUCT FAILURE 13. WARRANTY EXCLUSIONS... -
Page 3: Intended Use
1. INTENDED USE This tool is designed to cut wood that will fit the machine. Only use saw blades suitable for the machine and do not use cutting discs. 2. SAFETY INSTRUCTIONS 2.1 GENERAL POWER TOOL SAFETY INFORMATION WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. - Page 4 e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jeweler. Keep your hair, clothing and gloves away from moving parts.
- Page 5 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
- Page 6 workpiece as the saw is restarted. d) Support large panels to minimize the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.
- Page 7 When disposing of batteries, follow the instructions given in the section “Protecting the environment”. ▪ Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal ▪ directly or via accidental contact with metallic objects, the battery is short circuited and an intense current will flow causing heat generation which may lead to casing rupture or fire.
- Page 8 Children shall not play with the appliance. Cleaning ▪ and user maintenance shall not be made by children without supervision. If the supply cord is damaged, it must be replaced by ▪ the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. CAUTION: Do not recharge non-rechargeable batteries.
-
Page 9: Your Product
3. YOUR PRODUCT... - Page 10 (1) Lock button for on/off switch (16) Protective guard (2) Hex key (17) On/off switch (3) Auxiliary handle (insulated gripping surface) (18) Handle (insulated gripping surface) (4) Spindle lock button (19) Saw spindle (5) Base plate (20) Mounting flange (6) Wing bolt for parallel guide (21) Circular saw blade (7) Wing bolt for mitre/bevel angle preselection (22) Clamping flange...
-
Page 11: Specifications
Max cutting depth 52mm (90° ), 36mm (45° ) Miter angle 0 ° - 45 ° Φ165xΦ20x2.0x24T, max 7900/min Saw blade HSC20V2A Charger type Input 100-240V~ 50-60Hz, 0.4A; Output 20V d.c., 0.5A 10W Battery type HSC20V2A 20V d.c. 2.0Ah, Lithium-ion... -
Page 12: Assembly
5. ASSEMBLY WARNING ! Remove the battery pack before assembly. The tool should not use any abrasive wheel. Wear gloves to avoid the risk of injury. 5.1 INSERTING/CHANGING THE CIRCULAR SAW BLADE ➢ Only use saw blades that match the specifications given in this user guide. ➢... -
Page 13: Operation
6. OPERATION 6.1 CHARGING THE BATTERY PACK IMPORTANT: The battery pack is not fully charged at the factory. Before attempting to charge them, thoroughly read all of the safety instructions. To assure that the charger you use are applicable to the battery pack. 2) Insert the charger into 100-240V~,50-60Hz outlet. - Page 14 Remove the battery: press the battery release latch in and at the same time pull the battery pack off. To insert the battery, push the battery pack onto the contacts of the tool. 6.2 OPERATING MODES ➢ Remove the battery before carrying out any work on the power tool. Setting the cutting depth (see figure C) ➢...
-
Page 15: Cleaning, Maintenance And Storage
Sawing wood Choosing the right saw blade depends on the wood type, wood quality and whether cuts with or against the grain are required. Making cuts in spruce with the grain produces long, spiral- shaped chips. Beech and oak dust is especially detrimental to health. Therefore, work only with dust extraction. Sawing with a parallel guide (see figure D) The parallel guide allows you to make precise cuts along the edge of a workpiece and cut strips with the same dimensions. -
Page 16: Troubleshooting
8. TROUBLESHOOTING Problems Causes Solutions Cannot start Battery pack not properly Remove and reinsert battery pack installed The battery is discharged Charge the battery Internal damage or wear, example Repair repair center the engine is damaged approved maintenance Can only run slowly The battery is not charged Charge the battery The battery wears out... -
Page 17: Declaration Of Conformity
10. DECLARATION OF CONFORMITY BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux - France, declares that， Product: CORDLESS CIRCULAR SAW Trade mark: HYUNDAI Model: HSC20V2A Serial number: 20211164350-20211164749 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. -
Page 18: Warranty
11. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 19: Product Failure
12. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 20: Warranty Exclusions
13. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...