Related Manuals for Hyundai HSBE2652
Summary of Contents for Hyundai HSBE2652
- Page 1 ELECTRIC LOG SAW HSBE2652 WARNING: Read thoroughly the instruction manual before use.
-
Page 2: Table Of Contents
CONTENTS 1. INTENDED USE..................3 2. SAFETY INSTRUCTIONS..............3 3. TECHNICAL SPECIFICATIONS............8 4. ASSEMBLY..................9 5. OPERATION..................12 6. MAINTENANCE.................12 7. STORAGE..................13 8. TROUBLESHOOTING TABLE............13 9. DECLARATION OF CONFORMITY..........14 10. WARRANTY..................15 11. PRODUCT FAILURE.................16 12. WARRANTY EXCLUSIONS..............17... -
Page 3: Intended Use
1. INTENDED USE This machine is only intended for cutting firewood as detailed in these instructions. Unspecified use, modifications to the machine, or use of parts not tested and approved by the equipment manufacturer may cause unforeseeable damage! This machine is intended for operation by ONE person. Other persons shall keep a sufficient distance to the machine. - Page 4 Hearing protection to reduce the risk of induced hearing loss; Respiratory protection to reduce the risk of inhalation of harmful dust; Gloves for handling saw blades (saw blades should be carried in a holder wherever practicable). 9. Stop the machine running whilst unattended. 10.
- Page 5 machine. Turn power off if the machine is not used. Hazard generated by modification of the machine or use of parts not tested and approved by the equipment manufacturer! Use only parts approved by the equipment manufacturer. This applies particularly to : Saw blade (see “Technical specifications”) ON/OFF switch (type: KOA7) Motor (type: YY90-2-1)
- Page 6 where provided, dust extraction equipment to be switched on before commencing machining. It is important that: During operation the machine is standing on level, horizontal ground and that the floor area around the machine is level, well maintained and free from loose material e.g. chips and off-cuts;...
- Page 7 - Braking should be verified every before use, running the machine, switch off then check the stopping time. - Only saw blades made in conformity to EN 847-1:1997 shall be used on the machine; - The machine during indoor use shall be connected to an external chip and dust extraction system; - A Residual Current Device (RCD) should be used 2.5 DESCRIPTION OF THE SYMBOLS The use of symbols in this manual is intended to draw your attention to possible risks.
-
Page 8: Technical Specifications
The unit must be always operated by one person only. Other people should keep a safe distance from the work area, especially when the log saw is under operations. Never use another people to help you with freeing jammed log. Conforms to European standards. -
Page 9: Assembly
4. ASSEMBLY 1. Open package and take out all parts. (see picture 1) Picture 1 1. Main machine 6. cover for working table 2. Wheel parts 7.weight balancer 3. operating handle 8. connect plate for working table 4.ruler bar 9. working table 5. - Page 10 3. Assemble the wheel parts. Firstly disassemble all screws and nuts on it. Then connect it with the frame and tighten all screws and nuts (see picture 6 and picture 7). Position the wheel kit under the machine and screw the 4 bolts, nuts and washers into their places(see picture 8). Picture 6 Picture 7 Picture 8...
- Page 11 5. Assemble the working table cover. Insert the rotating block on cover into the corresponding fixing block on working table and fix it with M4x8 cross countersunk head screw (see picture 11). Picture 11 6. Assemble the operating handle. Put it into the right holes on working table and Screw on the 2 knobs after sliding the 2 tubes of the carrying handle (2 positions with notches: high and low).(see picture 12).
-
Page 12: Operation
8. Position the flyweight in its place and screw on the 2 nuts(see picture 15). Picture 15 5. OPERATION 5.1 SAWING 1. Open the machine by removing the safety bar at the bottom of the machine. 2. Turn on the machine. 3. -
Page 13: Storage
Ensure that there are no tools or other materials on or in the machine before putting it into operation. Exchange immediately rocker that run out. 6.1 BEFORE AND AFTER EACH USE Check the blade Make the air vents are never obstructed by debris or accumulation of other objects, as this may damage the engine or cause a fire risk. -
Page 14: Declaration Of Conformity
Tel: +33 (0)5.34.502.502 Fax: +33 (0)5.34.502.503 The undersigned, hereby certifies that the units described below ELECTRIC LOG SAW Model: HSBE2652 S/N: 20230310608-20230310679 is in compliance with the provisions of the following European directives: 2014/30/EU " Electromagnetic Compatibility " 2006/42/EC "Machinery"... -
Page 15: Warranty
10. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 16: Product Failure
11. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 17: Warranty Exclusions
12. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...