Download
Share
Print this page
Hyundai HSBT7672 Original Instructions Manual
  1. Manuals
  2. Brands
  3. Hyundai Manuals
  4. Saw
  5. HSBT7672
  6. Original instructions manual
Hyundai HSBT7672 Original Instructions Manual

Hyundai HSBT7672 Original Instructions Manual

Petrol log saw
Hide thumbs

Advertisement

Quick Links

Download this manual
1

Advertisement

loading

Related Manuals for Hyundai HSBT7672

Summary of Contents for Hyundai HSBT7672

  • Page 2: Table Of Contents

    CONTENTS 1. SAFETY WARNINGS 2. PRODUCT VIEW 3. ASSEMBLY 4. USE 5. MAINTENANCE 6. STORAGE 7. WARRANTY 8. DECLARATION OF CONFORMITY...

  • Page 3: Safety Warnings

    1. SAFETY WARNINGS When using this machine observe the following safety instructions, to exclude the risk of personal injury or material damage. Please also observe the special safety instructions in the respective chapters; where applicable, follow the legal directives or regulations for the prevention of accidents pertaining to the use of circular saw.
  • Page 4  Gloves for handling saw blades (saw blades should be carried in a holder wherever practicable). 9. Stop the machine running whilst unattended. 10. Report faults in the machine, including guards or saw blades, as soon as they are discovered. 11.
  • Page 5 moving the machine. 27. All operators must receive proper training in the use, adjustment and operation of the machine. 28. Make sure that the flanges used are as specified by the manufacturer , suitable for the intended use . 29. Make sure you include that necessary for operating the machine guards and other safety devices are fitted, they are in good operating condition and properly maintained.
  • Page 6 correctly installed and meet all conditions necessary for the proper operation of the machine. Damaged protection devices or parts must be repaired or replaced by a qualified specialist. Have damaged switches replaced by a service center. Keep handles free of oil, grease and resin.
  • Page 7 - It must be guaranteed that, during its entire service life, the machine, including its components, cannot overturn, fall or move in an uncontrolled manner, whether during transport, assembly, disassembly, deactivation and disposal. The machine must always remain on a stable flat surface, transport safely with the protection on the blade and the protections must always be in good working order.
  • Page 8 toxic carbon monoxide; Contact with the toxic exhaust gases can lead to unconsciousness and death. • The muffler will be very hot during operation and will remain hot for a while after the engine has stopped. Be careful not to touch the muffler when it is still hot. To avoid serious burns or the risk of fire, allow the engine to cool down before transporting it or storing it indoors.
  • Page 9 Use a push block or push stick to avoid working with the hands close to the saw blade when using a dual purpose circular sawing machine for firewood/circular saw bench in the saw bench mode; Wear suitable personal protective equipment when necessary; this could include; hearing protection to reduce the risk of induced hearing loss;...
  • Page 10 ■ Injuries caused by touching the rotating parts ■ Injuries caused by disruption of the cutting blade These risks are most evident: ■ Within the range of operation ■ Within the range of the rotating machine parts In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided.
  • Page 11 This symbol, before a safety comment, indicates a precaution, a warning or a danger. Ignoring this warning can lead to an accident for yourself or for others. To limit the risk of injury, fire, or electrocution always apply the recommendations indicated. Wear ear protection, eye protection, helmet, mask, non-skid footwear, gloves and face protection Saw blade for cutting wood.
  • Page 12 Keep children away. The unit must be always operated by one person only. Other people should keep a safe distance from the work area, especially when the log saw is under operations. Never use another people to help you with freeing jammed log. Choke lever &...
  • Page 13 manufacturer may cause unforeseeable damage! This machine is intended for operation by ONE person. Other persons shall keep a sufficient distance to the machine. TECHNICAL SPECIFICATIONS Engine power(4-cycle) 7600W/3200min Engine displacement 389cm Fuel tank capacity: 1.1 L Engine oil tank capacity: 6.5 L Saw blade Ø700mm x Ø30mm x 3mm x 42T...

  • Page 14: Product View

    2. PRODUCT VIEW 1. Handle 2. Protective cover 3. Saw 4. Sliding support 5. Spring hose 6. Wheel 7. Saw protection guard 8. Starter rope 9. Air filter 10. Fuel tank...

  • Page 15: Assembly

    3. ASSEMBLY NOTE: This machine is delivered already assembled. If parts of the machine are not assembled upon delivery, please follow the instructions below. If there is a problem with the assembly, contact our customer service. It is recommended that the machine is assembled by 2 people. a.
  • Page 16 c. Sliding support Unscrew the nut screw. Insert the sliding support into the hole in the tool. Screw with the screw nut to lock it. To adjust the position of the sliding support, unscrew the nut screw and then change the position of the sliding support.

  • Page 17: Use

    4. USE BEFORE STARTING Check and fill engine with approximately 1.1 litres SAE10W-30 oil. Fill the fuel tank with 93+octane unleadedgasoline STARTING THE ENGINE 1. Move the fuel valve lever to the ON position. 2. To start a cold engine, move the choke lever to the CLOSED position. To restart a warm engine, leave the choke lever in the OPEN position.
  • Page 18 4. Turn the engine switch to the ON position. 5. Operate the starter. RECOIL STARTER Pull the starter grip lightly until you feel resistance, then pull briskly. Return the starter grip gently. 6. If the choke lever has been moved to the CLOSED position to start the engine, gradually...
  • Page 19 move it to the OPEN position as the engine warms up. STOPPING THE ENGINE To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following procedure. 1. Move the throttle lever to the SLOW position. Some engine applications use a remotely-mounted throttle control rather than the engine-mounted throttle lever shown here.
  • Page 20 3. Turn the fuel valve lever to the OFF position. OPERATION Sawing 1. Open the machine by removing the safety bar at the bottom of the machine. 2. Turn on the machine. 3. Wait until the saw blade has reached its maximum speed. 4.

  • Page 21: Maintenance

    5. MAINTENANCE Warning: Turn off the machine and disconnect from the power supply before conducting maintenance work or settings. Wear goggles when cleaning the machine. Handle your device carefully and out of reach of the children. Have your tool repaired by a qualified person. This power tool complies with the applicable safety standards.
  • Page 22 Every 50 hours of operation Check all screwed connections, tighten if necessary (Rocker and rocker stop must remain movable) Saw blade change Danger! Directly after cutting the saw blade can be very hot – burning hazard! Let a hot saw blade cool down.
  • Page 23 6. Remove the nut and outer flange from the saw spindle Take the saw blade off the saw spindle.
  • Page 24 Clean clamping surfaces of : saw spindle, Inner flange, saw blade, Outer blade flange, Nut. Danger! Do not use cleaning agents (e.g. to remove resin residue) which could corrode the light alloy components; this can have an adverse effect on the machine’s stability. Do not clean the saw blade with combustible liquids.
  • Page 25 Note: Always install the transport brace before transporting the saw. To keep the saw blade from rusting, spray with Cleaning and Maintenance Spray (optional accessory) before storing it for a longer time. Every 50 hours of operation Check all screwed connections, tighten if necessary (Rocker and rocker stop must remain movable).

  • Page 26: Storage

    6. STORAGE Store the manual close to the machine. Always wait the appliance cool down before storage. Always store the log saw in a dry area. Wipe the log saw clean with a brush. Apply a thin layer of oil using an oily cloth to protect the machine from rust, before storage.

  • Page 27: Declaration Of Conformity

    Tel: +33 (0)5.34.502.502 Fax: +33 (0)5.34.502.503 The undersigned, hereby certifies that the units described below PETROL LOG SAW Model: HSBT7672 S/N: 20200613880-20200613894 is in compliance with the provisions of the following European directives: 2014/30/EU " Electromagnetic Compatibility ", 2006/42/EC "Machinery", 2011/65/EU "ROHS"...