Table of Contents
Advertisement
[PROJECTOR TYPE]
[SERIAL NUMBER]
[PROJECTOR RUNTIME]
[LIGHT RUNTIME]
[CONTINUOUS LIGHTING
TIME]
[FIRMWARE VERSION]
[INTAKE AIR TEMP.]
[OPTICS MODULE TEMP.]
[EXHAUST AIR TEMP.]
[LIGHT1 TEMP.]
*1
[LIGHT2 TEMP.]
*1
[SELF TEST]
[INPUT]
[SIGNAL NAME]
[MEMORY NO.]
[BACKUP INPUT STATUS]
[NUMBER OF REGISTERED
SIGNAL]
[COOLING CONDITION]
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS]
[AC VOLTAGE]
[LENS]
[ON COUNT]
[UPGRADE KIT]
[SLOT]
[OPERATING MODE]
[NORMAL]
[ECO]
[QUIET]
[USER1]
[USER2]
[USER3]
[CONSOLIDATED RUNTIME]
[ANGLE INFORMATION]
182 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Displays the type of the projector.
Displays the serial number of the projector.
Displays the runtime of the projector.
Displays the runtime of the light source 1 and the light source 2.
Displays the elapsed time from when the light source is illuminated.
The elapsed time after the illumination of the light source can be confirmed when adjusting the focus.
The elapsed time is reset when the light source is temporarily turned off such as using the shutter
function.
Displays the firmware version of the projector.
Displays the intake air temperature status.
*1
Displays the internal temperature status.
*1
Displays the exhaust air temperature status.
*1
Displays the light source 1 temperature status.
Displays the light source 2 temperature status.
Displays the self-diagnosis information.
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
Displays the input signal name.
Displays the memory number of the input signal.
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 125)
Displays the number of registered signals.
Displays the set cooling conditions.
Displays the control status of the REMOTE2.
Displays the input supply voltage.
[LENS TYPE]
[POWER ON TIMES]
[ET-NUK10]
Displays the product model number of the Function Board installed in <SLOT>.
Also, the firmware version is displayed after the product model number.
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
Displays the runtime of the light source with [OPERATING MODE] set to [ECO].
Displays the runtime of the light source with [OPERATING MODE] set to [QUIET].
Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the
time used with the [NORMAL] setting.
*2
The consolidated runtime is used for a rough indication about when to perform maintenance when the
projector is used in combination of each item in [OPERATING MODE].
[ROLL ANGLE]
[PITCH ANGLE]
Displays the projection lens type.
Displays the number of times the power is turned on.
Displays the activation status by the NFC Upgrade Kit (Model No.:
ET-NUK10).
Or, displays the status of the NFC function.
[ACTIVATED]: The NFC function can be used.
[NOT ACTIVATED]: The NFC function cannot be used.
Displays the horizontal swing angle based on the detection result of
*3
the built-in angle sensor.
Displays the vertical tilt angle based on the detection result of the
*3
built-in angle sensor.
Advertisement
Table of Contents
