Table of Contents
Advertisement
4.
5.
)
il
LJUUN-^t 1 I
(tvj [vct} [mjxI
A
—\
[AMPJ
^ a
rfM
Ay
fiM
Press the
PLAY
button 0 (►
OK),
The
LEARN
indicator
changes from blinking to continuously lit.
Press and hold the
PLAY
button on the laser disc player's remote
controller. The remote controller has finished learning the
command when OK appears on the LCD <D.
• If
AGAIN
appears on the LCD, some error has prevented the
command from being learned. If this happens, simply repeat
the procedure from step 4,
• In the rare event that
NG
appears on the LCD. it means that
the remote controller you are attempting to learn from uses
special signals that cannot be learned by the Marantz remote
controller,
6
.
Follow the same procedure to make the remote controller learn
the ten-key © operation used by the laser disc player's remote
controller,
7.
Repeat the procedure from step 3 to have the remote controller
learn the signal codes for the other components such as TV. VCR.
etc,
• If no buttons are pressed for approximately l minute while in
the LEARN mode, the remote controller automatically returns
to the USE mode.
• When programming the function buttons, first switch to the
desired function, then press the button again.
8.
When you have finished programming the remote controller, use
a ballpoint pen or other sharp point to once again press the
MODE
button Q] to return it to the USE mode. The LCD displays
the
USE
indicator, and the newly programmed codes rtow can be
used.
If FULL is displayed on the LCD
If
FULL
is displayed on the LCD © when programming in the LEARN
mode, it means that the memory has become too full to hold any
further codes.
if
FULL
is displayed no matter how many times you attempt to enter
new codes, it means that the remote controiter cannot accept any
new codes until some of the previously learned codes are deleted to
make space in the memory. Select unneeded codes for each of the
Jog Dial
control [U and
Function
buttons U], that show
FULL
and
delete them from the memory.
Note:
The power
ON
and
OFF
buttons E] can only be programmed to
learn one type of code, regardless of the function button that has
been selected.
Let's use the example of setting
disc player.
as the SIDE-B code for the laser
1
.
2
.
Use a ballpoint pen or other sharp point to press the MODE
button Q] until the LEARN indicator is displayed and starts to
Wirt<.
Place the laser disc's remote controller so that its infrared
fransmitter window is facing the infrared signal receiver window
on the Marantz remote controller at a distance of about 5
centimeters (2 inches).
3,
Press the
LD Function
button d).
4.
Rotate the
Jog Dial
ID left or right until
S
is displayed, then press
ttie
ENT
button (7].
• The
LEARN
and
NAME
indicators will both be displayed.
1
Tl
L 11
siJj'-i'e
1 IB! M 1 1 1 1 1 1
Press the
SIDE-B
button on the laser disc's remote controller
continuously until
OK
is displayed on the Marantz remote
controller's LCD, indicating that the programming has been
completed.
• If
AGAIN
appears on the LCD, some error has prevented the
command from being learned. If this happens, simply repeat
the procedure from step 4,
When the programming has been completed, the remote
controller automatically switches to the NAME mode.
The left hand position on the LCD © biinks, indicating the
character in the name to be rewritten.
/
s
/
Tl
LJJ
-•nv
1 IBM 1 1 M 1 1 1
O /A W/
• If you do not wish to rewrite the name, simply press the
OK
Cursor button US.
• If you wish to rewrite the name, input the desired characters
using the ten-key pad 0. The part of the display that is being
rewritten may be selected using the < and > Cursor buttons
03. When you are finished rewriting, press the OK Cursor
button 0.
To simply erase already existing characters, press the 0
button to replace them with a blank space.
(Refer to next section on rewriting names)
6.
Use the same procedure to program the codes for other 1-6 with
the
Jog Dial
(11.
7.
When finished programming the codes for each of the buttons,
use a ballpoint pen or other sharp point to press the
MODE
button Q] to return the remote controller to the USE mode. Once
USE
is displayed on the LCD, the newly memorized codes are
available tor use.
21
Advertisement
Table of Contents
