Table of Contents
Advertisement
LLJ
ciMi uuuun$»
Used to execute a function selected with the Jog Dial H].
There are 2 ENT buttons, one on each side, so that the remote
controller can be used just as easily with either hand.
The characters on the display can also be programmed.
Used to switch the remote controller to the command sets for specific
sources (amplifier, receiver, etc.), thereby allowing a single remote
controller to control up to 11 different components. To use these
buttons to switch the amplifier's source, press the desired button
twice within 2 seconds. The AMP button [E is used only to switch the
command set of the remote controller itself and therefore does not
transmit any signal. Further, the function buttons may also be
programmed to execute macros, (A macro ailo\Ars a crxnplex string of
operations to be performed in series simply by pressing a single
button.) One button can be programmed to learn sequences
containing up to 10 commands. The following is an example of a
macro sequence:
Turn the receiver ON
-¥
Switch the function to DVD
Set the
Surround Mode to Dolby Digital -> Switch the TV to video input
Set
the DVD player to Play.
dl VOLUME A up/? down buttons
Used to adjust the volume on receivers and other components
equipped with volume control.
M
CURSOR/TRANSPORTCONTROLbutlons
Used to operate on-screen and other displays used by receivers and
other components, as well as to operate the PLAY, STOP. PAUSE.
NEXT, and PREVIOUS functions of each source.
[n]
(CURSOR/TRANSPORT
CONTROL switching) button
Used to switch the function of the CURSOR/TRANSPORT CONTROL
buttons
between CURSOR and TRANSPORT CONTROL, with the
currently selected function displayed on the LCD when the DVD, LD,
or VCR functions are selected. When functions other than DVD. LD. or
VCR are selected, the < • ► button remains inactive.
iicH
I
vviiiuu'vtf
Used to transmit remote control signals based on beams of infrared
light to system components.
To ensure that these signals are
properly received, make sure that this window is pointing in the
general direction of the infrared receiver on the amplifier or other
components. This window should also be pointed toward the source
remote ccxttrofler when using Programmable Learning function.
Note:
The
MODE
IB,
MACRO
[E. and < • ► (CURSOR/TRANSPORT
CONTROL switching) O cannot be programmed,
LCD (Liquid Crystal Display)
information about currently selected functions and modes is
displayed on the LCD. Pressing any button will call up a full display of
information on the status of that function or mode. This display will
disappear after approximately 1 minute, except for the Function
Name indicator
which is always displayed.
@ Function Name indicator
Displays the name of the currently selected function (LD, TV, etc.)
using up to 5 characters.
® Command Name indicator
Displays up to 10 types of commands for each function using up to 5
characters.
M
CHANNEL A up/? down buttons
Used to controls the up/down function of tuner, or to cycle through the
tuner presets.
Used to temporarily mute the sound of preamplifiers, receivers, etc.
Used to call up the on-screen menus used to control DVD players,
digital satellite systems (DSS), and other menu-equipped systems.
Used to clear the contents of memory or programmed functions.
Bl MEMO button
Used to program your CD player's track memory, or to enter a VCR
recording program. Also can be used to provide the MEMO function
included with other components in your system.
Allows confirmation of current command page. Also, when setting or
transmitting macros, displays information such as the number of
macro steps and the time interval between command transmissions.
(9)
Transmission indicator
Indicates when the remote controller is transmitting a signal.
@ USE indicator
For normal operation the USE indicator is displayed.
Indicates when the remote controller is in the LEARN mode.
Indicates when the remote controller is in the NAME mode and a
command name is being changed.
Used to enter numeric digits, useful for finding a specific track on a
CD or for tuning to a preset radio station, etc. When the function is set
to AMP, it is possible to choose Surround Mode, etc.
© MACRO indScator
Indicates when the remote controller is in the MACRO mode.
® CURSOR indicator
Indicates w^en the CURSOR/TRANSPORT CONTROL button is in the
cursor mode.
19
Advertisement
Table of Contents
