Table of Contents
Advertisement
ft/lANUAL TUNING
1.
To select the tuner as the source, press the TUNER button ©(xi
the front panel or press the TUNER button [S on the r^note.
2.
Press the TUNER button ® on the front panel or press the
TUNER button [S on the remote to select the desired frequency
band if required.
3.
Press the F/P button ® on the front pane! to disf^ay the frequency.
4.
Press the TUNING/PRESET
A
or
T
button © on the front pane! or
press the
v button M on the remote,
5.
If FM is selected, press the MODE button ® on the front panel <x
select T-MOD in the tuner mode and press the ENT [3 butt<xi <xt
the remote coritroi to select the desired audio rhode.'^
~
(FM) MODE BUTTON OPERATION
When "AUTO" indicator is on in the display, FM stations that
broadcast in stereo will be received in stereo and the "STEREO"
indicator lights.
When "AUTO" indicator is off, all the FM stations will be received in
mono regardless of whether or not they are broadcasting in stereo.
AUTO TUNING (USING THE SR7000)
1,
Press the
button © on the front panel to display the frequency.
2.
Press the
TUNING/PRESET A
or
T
button © on the front panel
for more than 1 second to start the Auto tuning function.
AUTO TUNING (USING THE REMOTE CONTROL UNIT)
Press
V button 0 for more than
1
second to start the Auto tuning
function,
PRESET TUNING
With this unit you can preset up to 50 FM/AM stations in any order. For
each station, you can memorize the frequency and reception mode if
desired.
1-a. Manual Presetting (Using the SR7000)
1. Refer to the "MANUAL TUNING" or "AUTO TUNING" section
above to tune in a desired station.
«2.
Press the
MEMORY
button ©. "MEMO" indicator starts blinking
on the display.
While "MEMO" is still blinking (approx. 5 seconds), select the
preset number by pressing the
TUNING/PRESET
A or T button
© then press the
MEMORY
button © again.
3.
When a number has been property input, "MEMO" indicator
stops blinking and goes out.
The station is now stored in the specified preset memory location.
1*b. Manual Presetting (Using the remote unit)
1.
Tune in a desired station,
2.
Press the
MEMO
button 01,
3.
Enter the desired preset number with ten keypad E3.
' When entering a single digit number (2, for example), either input
"02'' or just input "2" and wait for a few seconds.
* If a number other than 1-50 is entered by mistake, that number
flashes in the display to indicate that if is invalid and frte display
returns to the original frequency display.
2. Auto Presetting
This function automatically scans the AM and FM band and enters all
stations with sufficient signal strength into the memory.
This function is available only for SR7000.
1.
Select the FM band with the BAND button on the remote.
2.
Tune in the lowest receivable frequency.
3.
While pressing the MEMORY button ®, press the TUNINQ/PRESET
A button ©, Auto memory starts at this point.
4. • "MEMO " will blink on the display.
5.
Each time the tuner finds a station, the scanning will pause and
the station will be played for five seconds. During this time, the
fdtowing operations are possible:
1)The band can be changed using the BAND button on the
remote.
2} The mode can be changed using the (FM) MODE button @ .
6.
If no button is pressed during this period, the current frequency is
preset in location CH-2.
If you wish to skip the current station, press the njNINGff'RESET A
or ▼ button ® during this period, the current frequency is skipped
and auto presetting continues.
7.
Operation stops automatically when all 50 preset memory
positions are filled or when auto scanning attains the highest end
of all bands.
To stop the auto preset function at anytime, press the CLEAR
"button®.
..
3. Recalling a Preset Station
1.
Press the
F/P
button © to change the display to preset.
2.
Select the desired preset station by pressing TUNING/PRESET
A or ▼ button © on the front panel or press CHA or CHT button
01
CXI the remote.
Note:
To directly access the preset stations using the numeric keypad,
select the desired preset station by entering one or two digits
using the numeric keypad 01.
To return to the Manual Tuning mode, press the
F/P
button ©,
4. Preset Scan Tuning (Using the remote control unit)
1.
Select the
SCAN
(preset scan: command page 5 in TUNER
mode) by
Jog Dial
\B and press the
ENT
button [3 on the remote
control. "P-SCAN" indicator blinks in the display. (The preset
station with the smallest preset number is recalled first. If no
stations have been preset, CH "00" blinks in the display and the
unit returns to the previous mode.)
2.
Preset stations are recalled in sequence (CH-1
CH-2, etc.) for
5 seconds each. Preset numbers that do not contain stations are
skipped.
3.
You can fast forward the preset stations by pressing the CHA
button continuously.
When the desired preset station is received, cancel the preset
scan operation by pressing the CHV button or the CLEAR button
®.
5. Clearing Preset Stations
You can remove preset stations from memory using the following
procedure.
1.
Recall the preset number to be cleared with the method
described in "Recalling" a preset station .
2.
Press the MEMORY button ® on the front panel or MEMO button
m on the remote unit. "MEMO" biinks in the display for 5 seconds.
While "MEMO" is stili blinking, press the CLEAR button ® on the
front panel or CLEAR button dl on the remote unit,
"CLEAR" appears on the display to indicate that the specified
preset number has been cleared.
Advertisement
Table of Contents
