Page 2
Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest version from www.chauvetprofessional.com.
Table of Contents TABLE OF CONTENTS 1. Before You Begin ............... What Is Included ................... Claims ......................Text Conventions ..................Symbols ......................Safety Notes....................FCC Statement of Compliance ..............RF Exposure Warning for North America and Australia........ Expected LED Lifespan................. 2.
Page 4
Table of Contents IP Address ....................... 17 Ethernet to DMX ...................... 17 Control Channel Assignments and Values............ 16Ch / 15Ch2 / 15Ch1 / 11Ch / 10Ch ..............8Ch2 / 8Ch1 / 6CH / 5Ch / 4Ch / 3Ch ..............1Ch........................Control Chart......................
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate a claim. In addition, keep the box and contents for inspection.
• In the event of a serious operating problem, stop using immediately. If a Chauvet product requires service, contact Chauvet Technical Support. onAir IP Panel 1 User Manual Rev. 3...
Before You Begin FCC Statement of Compliance This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Introduction 2. Introduction Description The onAir IP Panel 1 is an IP65 full-spectrum LED soft light with a 1x1 format for outdoor or indoor operation. Ready for any broadcast setting, the onAir IP Panel 1 features high CRI/ TLC and TM-30 scores, a smooth 16-bit dimming curve, +/- green adjustment, an emulated redshift, built-in customizable effects, and a drop-in slot for easy changing of accessories.
Introduction Product Dimensions 22 in 559 mm 19.6 in 497.8 mm 11.81 in 300 mm 13.98 in 16.18 in 355 mm 411 mm 1.1 in 28 mm 21.81 in 554 mm 17.05 in 433.1 mm 13.97 in 354.9 mm 5.74 in 146 mm onAir IP Panel 1 User Manual Rev.
Setup 3. Setup AC Power The onAir IP Panel 1 has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Setup USB Software Update The onAir IP Panel 1 allows for software updates with a USB device using the built-in USB port. To update the software using a USB flash drive, do the following: 1. Power on the product, and plug the flash drive into the USB port. 2.
If the user is not familiar with or need more information about DMX standards or the DMX cables needed to link this product to a DMX controller, download the DMX Primer from the Chauvet website: www.chauvetprofessional.com. DMX Linking The onAir IP Panel 1 can be linked to a DMX controller using a 5-pin DMX connection or a CRMX™...
Setup Lumenradio CRMX™ Connection In optimal conditions, the onAir IP Panel 1 can operate up to 300 m (900 ft) away from the CRMX™ transmitter, The CRMX™ receiver in the onAir IP Panel 1 must be paired with the CRMX™ transmitter for wireless operation.
The onAir IP Panel 1 comes with an omega bracket and a junior pin. Mounting clamps are sold separately. Make sure the clamps are capable of supporting the weight of this product. Use at least two mounting points per product. For the Chauvet Professional line of mounting clamps, go to http://www.trusst.com/products.
Operation 4. Operation Control Panel Description Button/Knob Function <MENU> Exits from the current menu or function Enables the currently displayed menu or sets the currently selected value into the <ENTER> selected function Navigates upwards through the menu list or increases the numeric value when in a <UP>...
Operation Menu Map Refer to the onAir IP Panel 1 product page on www.chauvetprofessional.com for the latest menu map. Main Menu Programming Levels Description DMX512 Protocol Artnet Sets the control protocol sACN Selects DMX address (*Highest 001–512* channel restricted to personality Address chosen) Preset...
Page 18
Operation Main Menu Programming Levels Description 600Hz 1200Hz 2000Hz Sets the Pulse Width Modulation Frequency frequency 4000Hz 6000Hz 25KHz Auto Sets the fan to auto mode Sets the fan to always on Fan Mode Sets the fan to always off Silent Sets the fan to silent Receive Off/...
Operation Home Screen The home screen of the onAir IP Panel 1 shows the current settings and status of the product. To see the home screen, press and hold <MENU> until it shows on the display. From the home screen, press <MENU>...
Operation Controlled Configuration Use control configurations to operate the product with a DMX, Art-Net™, or sACN controller. Control Mode The onAir IP Panel 1 works with wired DMX, CRMX™, Art-Net™, and sACN control signals. To select which protocol to use: 1.
Operation IP Address To set the IP address: 1. Go to the Ethernet Setting main level. 2. Select the IP Address option. 3. Select the first value of the IP address, from 2, 10, or 239. 4. Press <ENTER> to cycle through the 4 values of the IP address. 5.
Operation Standalone Configuration In a standalone mode, the onAir IP Panel 1 can be controlled through the display menu, the control knobs, and/or the preset buttons. CCT Control In CCT Control mode, the control knobs have the following functions: • <DIM/INTENSITY>: Increase or decrease the dimmer value, from 00.0–100%.
Operation Effect Macros The onAir IP Panel 1 features 8 effect macros which simulate lighting effects. 1. Go to the Effect Macros main level. 2. Select the effect macro, from Color Chase, Police Car, Firetruck, Fire, Clouds, Fireworks, Paparazzi, or Lightning. 3.
Operation Wireless Lumenradio CRMX™ Settings Toggle CRMX™ To enable or disable wireless CRMX™ control: 1. Go to the Wireless Setting main level. 2. Select the Receive Off/On option. 3. Select from Off (disabled) or On (enabled). Receiver Reset To reset the CRMX™ receiver: 1.
Maintenance 5. Maintenance Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean all lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.
Technical Specifications 6. Technical Specifications Dimensions and Weight Length Width Height Weight 22 in (559 mm) 5.74 in (146 mm) 21.81 in (554 mm) 28 lb (12.7 kg) Note: Dimensions in inches are rounded. Power Power Supply Type Range Voltage Selection Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging...