3M DBI SALA EXOFIT X200 Series User Instructions
Full body harness
Hide thumbs
Also See for DBI SALA EXOFIT X200 Series:
- User instructions (41 pages) ,
- User instructions (37 pages)
Table of Contents
Advertisement
Quick Links
;
For identification of product codes, refer to Table 1. See "Table 1 - Product Specifications" for more product information.
11
9
2
1
11
16
12
9
3
A
8
2
1
11
16
12
9
3
B
PARK
LANYARD
HERE, SEE
INSTRUCTIONS.
1
PARK
LANYARD
HERE, SEE
INSTRUCTIONS.
OSHA 1910.140
ANSI Z359.11
OSHA 1926.502
Figure 1 - Product Overview
12
Harness
Harness
Style
Model
1402000
1402001
1402002
1402003
1402004
1402005
7
1402006
1402007
1402008
1402009
A
1402010
1402011
1402012
1402013
1402014
1402015
1402016
1402017
1402018
1402019
1402020
1402021
1402022
1402023
1402024
1402025
1402026
7
B
1402027
1402028
1402035
1402036
1402037
1402038
1402039
6
PARK
LANYARD
HERE, SEE
INSTRUCTIONS.
3
4
2
PARK
LANYARD
HERE, SEE
INSTRUCTIONS.
PARK
LANYARD
HERE, SEE
INSTRUCTIONS.
EXOFIT™ SERIES X200
FuLL BODy HARnESS
USER INSTRUCTIONS
1
2
3
4
5
6
Attachment Elements
5
7
PARK
LANYARD
HERE, SEE
INSTRUCTIONS.
5908522 R
. B
Ev
7
8
9
10
11
12
Buckles and
Adjusters
Other Elements
8
13
14
15
16
Pads
© 3M 2021
Advertisement
Table of Contents
Related Manuals for 3M DBI SALA EXOFIT X200 Series
Summary of Contents for 3M DBI SALA EXOFIT X200 Series
- Page 1 1402038 1402039 PARK PARK LANYARD LANYARD HERE, SEE HERE, SEE INSTRUCTIONS. INSTRUCTIONS. PARK PARK LANYARD LANYARD HERE, SEE HERE, SEE INSTRUCTIONS. INSTRUCTIONS. PARK PARK LANYARD LANYARD HERE, SEE HERE, SEE INSTRUCTIONS. INSTRUCTIONS. © 3M 2021...
- Page 2 Figure 1 - Product Overview Harness Harness Buckles and Style Model Attachment Elements Adjusters Other Elements Pads 1402040 1402041 1402042 1402043 1402044 1402050 1402051 1402052 ...
- Page 3 Figure 1 - Product Overview Harness Harness Buckles and Style Model Attachment Elements Adjusters Other Elements Pads 1402093 1402094 1402095 1402096 1402097 1402098 1402104 1402105 1402106 ...
- Page 4 Figure 1 - Product Overview Harness Harness Buckles and Style Model Attachment Elements Adjusters Other Elements Pads 1402145 1402146 1402147 1402148 1402149 1402150 1402151 1402152 ...
-
Page 5: Safety Information
Never exceed the maximum free fall distance specified for your Fall Protection equipment. Do not use any Fall Protection equipment that fails inspection, or if you have concerns about the use or suitability of the equipment. Contact 3M Technical Services with any questions. -
Page 6: Product Overview
Always ensure you are using the latest revision of your 3M instruction manual. Visit www.3m.com/userinstructions or contact 3M Technical Services for updated instruction manuals. PRODUCT OVERVIEW: Figure 1 illustrates available 3M™ DBI-SALA X200 Full Body Harness models. Harness models are defined by their general ®... -
Page 7: Additional Materials
Before using this equipment, record the product identification information from the ID label in the “Inspection and Maintenance Log” at the back of this manual. Table 1 - Product Specifications System Specifications Each product model is certified to, or conforms with, the applicable standards and Standards: regulations listed within Figure 1. -
Page 8: Product Application
Hazards may include, but are not limited to: high heat, chemicals, corrosive environments, high voltage power lines, explosive or toxic gases, moving machinery, sharp edges, or overhead materials that may fall and contact the user or equipment. Contact 3M Technical Services for further clarification. - Page 9 MAKING CONNECTIONS: All connections must be compatible in size, shape, and strength. See Figure 4 for examples of inappropriate connections. Do not attach snap hooks and carabiners: To a D-ring to which another connector is attached. In a manner that would result in a load on the gate. Large-throat snap hooks should not be connected to standard- size D-Rings or other connecting elements, unless the snap hook has a gate strength of 16 kN (3,600 lbf) or greater.
-
Page 10: Installation
Never use D-ring extensions in leading edge applications. FASTENING BUCKLES: 3M Harnesses are equipped with a variety of Buckles for fastening and adjusting Leg Straps and Chest Straps. See Figure 1 for the buckle types present on your harness. Figure 6 illustrates operation of each of the... - Page 11 Fasten and adjust the Chest Strap. The Chest Strap should be approximately 6.0 in. (15 cm) down from the top of your shoulders. When comfortably adjusted, tuck the loose end of the Chest Strap under the Strap Keeper. Adjust the Shoulder Straps for a snug, comfortable fit with the Torso Adjusters. Each Shoulder Strap should be adjusted to the same length.
- Page 12 Figure 8 - Donning the Harness Figure 9 - Securing Lanyards with Loop Ends...
- Page 13 INSTALLING A HARNESS-MOUNTED SRD: Harness-mounted SRDs are secured directly to harnesses by means of a harness interface. Harness interfaces are a type of connector specially designed for this purpose. In general, there are two types of harness interface: straight-pin and carabiner. Instructions for each style are provided below. Instructions may vary per harness interface model.
- Page 14 Figure 10 - Straight-Pin Interface Figure 11 - Carabiner Interface...
- Page 15 PARK LANYARD PARK LANYARD HERE, SEE INSTRUCTIONS. HERE, SEE INSTRUCTIONS. PULL DEPLOY 1. DEPLOY BOTH PACKS. 2. INSERT HOOK INTO LOOP ON OPPOSITE STRAP. 3. PLACE BOTH FEET INTO WEB LOOP. 4. REHOOK TO ADJUST LOOP LENGTH IF REQUIRED. 3M.com/FallProtection...
-
Page 16: Maintenance, Service, And Storage
CLEANING: 3M Full Body Harnesses must be cleaned in accordance with 3M instructions. To clean the harness, wash in a mild, bleach-free detergent and then rinse. The harness should afterwards be hung to air-dry. Water used for cleaning and temperatures used to air-dry must never exceed 130°F (54.4°C). -
Page 17: Labels And Markings
Warning: Increased free fall should be considered when using this product. RFID Tag LOCATION: 3M product covered in these user instructions is equipped with a Radio Frequency Identification (RFID) Tag. RFID Tags may be used in coordination with an RFID Tag Scanner for recording product inspection results. See Figure 15 for where your RFID Tag is located. - Page 18 Figure 15 - RFID Tag Location PARK PARK LANYARD HERE, SEE LANYARD HERE, SEE INSTRUCTIONS. INSTRUCTIONS. Figure 16 - Product Labels PARK LANYARD PARK LANYARD PARK LANYARD PARK LANYARD HERE, SEE INSTRUCTIONS. HERE, SEE INSTRUCTIONS. HERE, SEE INSTRUCTIONS. HERE, SEE INSTRUCTIONS.
-
Page 19: Inspection Procedure
Table 2 – Inspection and Maintenance Log Model Number (Serial Number): Date Purchased: Date of First Use: ··· This product must be inspected by the user before each use. Additionally, a Competent Person other than the user must inspect this equipment at least once each year. ···... - Page 20 These are general requirements and information provided by ANSI/ASSP Z359. 3M Fall Protection may impose more stringent restrictions on the use of its products; refer to your 3M instruction manual for more information. It is essential that the users of this type of equipment receive proper training and instruction, including detailed procedures for the safe use of such equipment in their work application.
- Page 21 ANSI/ASSP Z359.11 American National Standard ANSI/ASSP Z359 Requirements for Annex A Proper Use and Maintenance of Full Body Harnesses 12. Frontal – The frontal attachment serves as a ladder climbing connection for guided-type fall arresters where there is no chance to fall in a direction other than feet first, or may be used for Work Positioning. Supporting the user, post-fall or during work positioning, by the frontal attachment will result in a sitting body position, with the upper torso upright, with weight concentrated on the thighs and buttocks.
- Page 24 LIMITED REMEDY: Upon written notice to 3M, 3M will repair or replace any product determined by 3M to have a factory defect in workmanship or materials. 3M reserves the right to require product be returned to its facility for evaluation of warranty claims. This warranty does not cover product damage due to wear, abuse, misuse, damage in transit, failure to maintain the product or other damage beyond 3M’s control.