20. Make your workshop child proof with padlocks, intended use. If used for other purposes, master switches or by removing safety keys. Powermatic disclaims any real or implied 21. Give your work undivided attention. Looking warranty and holds itself harmless from any around, carrying on a conversation and “horse-...
27. Keep hands clear of the blade area. Do not WARNING: Drilling, sawing, sanding or reach past the blade to clear parts or scrap machining wood products generates wood dust with the saw blade running. Never saw and other substances known to the State of freehand.
Additional knowledge can be obtained from experienced users or trade articles. Whatever accepted methods are used, always make personal safety a priority. If there are questions or comments, please contact your local supplier or Powermatic. Powermatic can also be reached at our web site: www.powermatic.com.
84 in. (213 cm) The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, Powermatic reserves the right to change specifications at any time and without prior notice, without incurring obligations.
Read and understand the entire contents of this manual, and your table saw manual, before attempting set-up or operation. Failure to comply may cause serious injury. 5.0 Unpacking 5.1 Shipping contents Figure 5-1: contents of Box #1 Open shipping cartons and check that all parts are intact.
The following instructions are for installing the Accu-Fence and Rail System on a Powermatic Model PM2000B or PM3000B table saw. The rails should bolt up to the Powermatic saw without any drilling. For mounting to a non-Powermatic saw, see sect.
Figure 6-6: for PM2000B Installing on PM3000B (non-folding legs): Position legs at inside corners of wood table at the end where the Powermatic logo is placed. See Figure 6-6b). Note: If you are using a mobile base under your saw, you may need to shift the placement of the legs so that they rest properly upon the shelves of the base.
Page 10
The Powermatic logo guide. See Figure 6-9. (You may wish to drill should face outward. The extension table is not 3/32"...
Measure distance from edge of guide tube to front rail; do this at both ends of guide tube to ensure guide tube is parallel to front rail. (The distance itself is not important, but it should be the same along the length of the guide tube.) NOTE: Install table saw switch onto front rail at the same time as the guide tube.
6.6.3 Clamping pressure adjustment Accu-Fence been pre-set manufacturer to lock securely when handle is pushed down. If adjustment is needed: Unlock fence and remove it from guide rail. Adjust each of two setscrews (C, Figure 6-17) exactly the same number of rotations until fence is held securely when handle is pushed down.
Saw properly. Place an adjustable square on the table, as shown in Figure 7-3. The following instructions are for installing the Accu-Fence and Rail System on a table saw other than a Powermatic model. Some drilling is required. ...
See Figure 7-8. Finger-tighten only at this time. The rest of the installation is the same as with a Powermatic table saw. Refer back to sect. 6.4 to mount the optional wood extension table (if Figure 7-3 applicable) and the guide tube in sect.
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1- 800-274-6848 Monday through Friday (see our website for business hours, www.powermatic.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
8.1.2 Rail Assembly – Parts List Index No Part No Description Size ....2653031B ....50" PW Rail Set for PM2000B & PM3000B ............... 2653039B ....30" PW Rail Set for PM2000B ................... PM2000B-HK-50 ..Hardware Kit for 50" Rail Assembly (includes #1 thru 9) ........ 1 1 ....
Powermatic sells through distributors only. The specifications listed in Powermatic printed materials and on the official Powermatic website are given as general information and are not binding. Powermatic reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.