Advertisement
Quick Links
Air conditioner
Installation manual
Wired remote controller MWR-SH11N
• Thank you for purchasing this Samsung Product.
• Before operating this unit, please read this installation manual carefully and retain it for future
reference.
DB68-08073A-00
SOL 터치간단유선 유럽향 IM_EN_DB68-08073A-00.indd 1
2018-10-11 오후 3:35:04
Advertisement
Related Manuals for Samsung MWR-SH11N
Summary of Contents for Samsung MWR-SH11N
- Page 1 Air conditioner Installation manual Wired remote controller MWR-SH11N • Thank you for purchasing this Samsung Product. • Before operating this unit, please read this installation manual carefully and retain it for future reference. DB68-08073A-00 SOL 터치간단유선 유럽향 IM_EN_DB68-08073A-00.indd 1 2018-10-11 오후 3:35:04...
-
Page 2: Table Of Contents
Contents Preparation Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before installation . -
Page 3: Preparation
Preparation Safety precautions This installation manual explains how to install a wired remote controller connected to the indoor unit of your Samsung system air conditioner . Please read this manual thoroughly before installing the product . (Please refer to appropriate installation for any optional product installation . ) WARNING Hazards or unsafe practices that may result in severe personal injury or death. - Page 4 Safety precautions CaUtION Do not install the product where there’s combustible gas. f Potential risk of fire and explosion . Ensure no water gets into the wired remote controller. f Potential risk of electric shock or fire . Install the air conditioner away from direct exposure to sunlight, in room temperature range of 0 °C(32 °F) ~ 39 °C(102 °F).
-
Page 5: Before Installation
Before installation Optional accessories Wired remote M4x16 screw (4) User manual (1) Installation manual (1) controller (1) • The wired remote controller should be installed by an installation expert . • Check and confirm the power is off before installing your wired remote controller . CaUtION •... -
Page 6: Installation
Installation Wired remote controller installation Wired remote controller installation 1 . Insert a small flat head screwdriver into the square groove in the bottom of your wired remote controller, and then pull up the front cover to separate it from the rear cover . 2 . - Page 7 3 . Using more than two screws, firmly affix the rear cover of the remote controller to the wall, and then connect the communication and power cable [(F3,F4) or (3, 4)], making sure these cables have reasonable length, to the terminal at the back of the cover .
- Page 8 Wired remote controller installation tracking your indoor unit from the wired remote controller Indicates tracking in progress Displays the total number of indoor units searched 1 . Tracking of your wired remote controller will automatically start when you turn on the power after installation . 2 .
- Page 9 Individual control with your wired remote controller Individual control means that you are using one remote controller to control one indoor unit . Outdoor unit COM1(F1, F2) COM1(F1, F2) Indoor unit Indoor unit Indoor unit COM2(F3, F4) COM2(F3, F4) COM2(F3, F4) Wired remote Wired remote Wired remote...
- Page 10 Wired remote controller installation Group control with your wired remote controller Group control means that you are using one wired remote controller to control two or more indoor units at the same time . 1 . Using one wired remote controller to control three indoor Units Outdoor unit COM1(F1, F2) COM1(F1, F2)
- Page 11 Controlling 2-remote controller 2-Remote controller is controlling one indoor unit or a group of indoor units with two remote controllers . Outdoor unit COM1(F1, F2) Indoor unit COM2(F3, F4) Wired remote Wired remote controller (Master) controller (Slave) • For the slave wired remote controller settings, please refer to the sections about the additional functions of the wired remote controller .
- Page 12 Wired remote controller installation Initializing your wired remote controller communication If the number of indoor unit is decreased while you are using your remote control to control one indoor unit or a group of indoor units, then you need to initialize your remote controller communication . Press the top right corner (hidden button) of the display for more than 7 seconds .
- Page 13 Errors displayed on your wired remote controller Error codes for the wired remote controller and the indoor units connected to your wired remote controller will be displayed in the LCD display . LCD Display When an error occurs in your indoor/outdoor units (product group display : a) - The product address for the error will be displayed, followed by the error code .
- Page 14 Wired remote controller installation Wired remote controller error codes Display Description Communication error between wired remote controller and indoor units (When communication is lost for over 3 minutes after detecting the indoor unit and the wired remote controller) No communication between Master(Main) and Slave(Sub) wired remote controllers No communication between wired remote controller and indoor units (Including communication error between indoor units and outdoor units) - Exceeded maximum number of indoor unit connection (16 indoor units)
-
Page 15: Wired Remote Controller Installation/Service Mode
Wired remote controller installation/service mode additional functions of your wired remote controller Setting Sub menu value Page Main menu ①② Move menu Move page 1 . If you want to use the various additional functions for your wired remote controller, press the top right corner (hidden button) of the display for more than 3 seconds and drop it . - Page 16 Wired remote controller installation/service mode additional functions of your wired remote controller • If communication initialization is needed after the setting, the system will reset automatically and communication will be initialized . NOtE Setting value Main Function description Page Save location menu menu Value...
- Page 17 Setting value Main Function description Page Save location menu menu Value Factory default Indoor unit Use of discharge 0 - No use, 1 - Use Indoor unit discharge temperature control temperature Cooling discharge temperature 8~18 °C Indoor unit setting/ Heating discharge temperature 30~43 °C Indoor unit checking 2)*...
- Page 18 Wired remote controller installation/service mode 4)* RMC(1) : 0~F/RMC(2) : 0~F (hexadecimal digits) When RMC(1) is set as F, RMC(2) setting is only available up to E . (RMC(1): Group channel, RMC(2): Group address) • Main address of the indoor unit is displayed and entered in hexadecimal digits . Please refer to the following table . NOtE Hexadecimal Decimal Hexadecimal Decimal...
- Page 19 6)* Setting is available when there is only 1 indoor unit connection and while the indoor unit operation is not operating . 7)* You can see no . 0 (no use) and no . 1 (use) while mode master indoor unit setting . For the mode master indoor unit setting, select the no .
- Page 20 SOL 터치간단유선 유럽향 IM_EN_DB68-08073A-00.indd 20 2018-10-11 오후 3:35:07...