Roland SC-8820 Owner's Manual page 65

36: OD Flanger (Overdrive
This effect connects an overdrive and a flanger in series.
fig.9-39
L
Overdrive
R
OD Drive (Overdrive Drive)
Adjusts the degree of overdrive distortion. The volume will
change together with the degree of distortion.
+OD Pan (Overdrive Output Pan) L63–0–R63 [2 (40 03 04)]
Adjusts the stereo location of the overdrive sound. L63 is
far left, 0 is center, and R63 is far right.
OD Amp (Overdrive Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3 (40 03 05)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
OD Amp Sw (Overdrive Amp Switch)
Turns OD Amp on/off.
FL Dly (Flanger Pre Delay)
Adjusts the time delay from when the direct sound begins
until the flanger sound is heard.
FL Rate (Flanger Rate)
Adjusts the modulation speed of the flanger effect.
FL Depth (Flanger Depth)
Adjusts the modulation depth of the flanger effect.
FL Fb (Flanger Feedback Level)
0B)]
Adjusts the proportion (%) of the flanger sound that is fed
back into the effect. Negative (-) settings will invert the
phase.
#FL Bal (Flanger Balance)
Adjusts the volume balance between the sound that passes
through the flanger and the sound that does not. With a
setting of D>0E, only the overdrive sound will be output,
and with a setting of D0<E, the overdrive sound that passes
through the flanger will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the low frequency gain.
Hi Gain (High Gain)
Adjusts the high frequency gain.
Level (Output Level)
Adjusts the output level.
Flanger) [02H, 01H]
EQ
Flanger Balance
EQ
0–127 [1 (40 03 03)]
Off/On [4 (40 03 06)]
0–100ms [6 (40 03 08)]
0.05–10.0 [7 (40 03 09)]
0–127 [8 (40 03 0A)]
-98%–+98% [9 (40 03
100:0–0:100(D:E) [10 (40 03 0C)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
0–127 [20 (40 03 16)]
37: OD Delay (Overdrive
This effect connects an overdrive and a delay in series.
fig.9-40
L
Overdrive
R
OD Drive (Overdrive Drive)
Adjusts the degree of overdrive distortion. The volume will
change together with the degree of distortion.
+OD Pan (Overdrive Output Pan) L63–0–R63 [2 (40 03 04)]
Adjusts the stereo location of the overdrive sound. L63 is
far left, 0 is center, and R63 is far right.
OD Amp (Overdrive Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3 (40 03 05)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
OD Amp Sw (Overdrive Amp Switch)
Turns OD Amp on/off.
Dly Time (Delay Time)
Adjusts the time delay from when the direct sound begins
until the delay sound is heard.
Dly Fb (Delay Feedback Level) -98%–+98% [7 (40 03 09)]
Adjusts the proportion (%) of the delay sound that is fed
back into the effect. Negative (-) settings will invert the
phase.
Dly HF (Delay HF Damp)
Adjusts the frequency above which delayed sound fed back
to the effect will be cut. If you do not wish to cut the high
frequencies of the feedback, set this parameter to Bypass.
#Dly Bal (Delay Balance) 100:0–0:100(D:E) [10 (40 03 0C)]
Adjusts the volume balance between the sound that passes
through the delay and the sound that does not. With a
setting of D>0E, only the overdrive sound will be output,
and with a setting of D0<E, the overdrive sound that passes
through the delay will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the low frequency gain.
Hi Gain (High Gain)
Adjusts the high frequency gain.
Level (Output Level)
Adjusts the output level.
Effects
Delay) [02H, 02H]
EQ
Delay Balance
EQ
0–127 [1 (40 03 03)]
Off/On [4 (40 03 06)]
0–500ms [6 (40 03 08)]
315–8k/Bypass [8 (40 03 0A)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
0–127 [20 (40 03 16)]
65