Application Advice; Maintenance & Service; Noise / Vibration - Skil 3085 Original Instructions Manual

within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level 7b is shown by the battery level indicator
when pressing button M; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• Holding and guiding the tool t
! while working, always hold the tool at the grey-
coloured grip area(s)
- always use auxiliary handle N, which can be mounted
on either side of the tool, depending on personal
preference and comfort. Loosen or fasten the auxiliary
handle as shown y
- keep ventilation slots H 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
Emergency switch-off (Anti-kickback brake technology)
•
The rapid switch-off function (Anti-kickback brake
technology) gives the user greater control over the power
tool and offers them better protection than power tools
that do not have Anti-kickback brake technology.
- The tool will switch off if it suddenly and unforeseeably
rotates around the drilling axis.
- To switch the tool back on, release the on/off switch
and then press it again.

APPLICATION ADVICE

• Use the appropriate bits u
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• Splinterfree drilling in wood i
• Dustfree drilling in walls o
• Dustfree drilling in ceilings p
• Drilling in tiles without skidding a
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots H 2)
! remove battery from tool before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Only for EU countries
• Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK countries
• Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of on Waste Electric and Electronic
Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound
pressure level of this tool is 95 dB(A) and the sound
power level 103 dB(A) (uncertainty K = 5 dB), and the
vibration Þ (triax vector sum; uncertainty K = 1.5 m/s²)
when drilling in metal <2.5 /s²
✱
when impact drilling in concrete 18.17 m/s²
✱
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Perceuse à percussion/
visseuse sans fil et sans balai
INTRODUCTION
• Cet outil est destiné au serrage et au desserrage des vis,
au perçage dans le bois, la céramique et le plastique et
au perçage à percussion dans la brique.
Cet outil n'est pas conçu pour un usage professionnel.
•
13
3085