PRESONUS StudioLive 16.0.2 Owner's Manual page 24

5 Scenes, Presets, System Menu, and MIDI Control
5.1 Creating and Recalling a Scene
Located at position S1 is a Scene named Zero Out (Board Reset). This Scene
cannot be overwritten and returns your StudioLive to its defaut factory
setting. All you have to do is lower the faders and return all trim knobs and
output volume knobs (Solo bus, FXA and FXB output, Phones, and Monitor)
to their lowest position. Your StudioLive will be zeroed out as follows:
INPUTS & BUSES ASSIGN PAN SOLO
INPUT CHANNELS MAINS C OFF
SUBGROUPS NULL C OFF
AUXES 1-4 N/A C OFF
FX A / FX B MAINS C
FX A & B NULL C
TALKBACK NULL
MAIN BUS C
SOLO BUS
MONITOR BUS
TAPE IN
METER MODE
MASTER CONTROL
The Fat Channel will be restored to the same setting for every input and
output on your StudioLive. Each of the dynamics processors and the three
bands of the EQ will be turned off. Their parameters will be set as follows:
FAT CHANNEL PARAMETERS
HIPASS NOISE GATE LIMITER COMPRESSOR
75 Hz THR N/A OFF THR 0 dB
RAT 2:1
RESP MED
GAIN 0 dB
POWER USER TIP: Before beginning any new mixing situation, it is always recommended
to recall the Zero Out (Board Reset) Scene. This is the easiest way to ensure that there are
no lingering parameter settings that could cause you some trouble in your new mix.
40 40
PreSonus StudioLive ™ 16.0.2
SETTINGS
MUTE SELECT LINK SENDS MODE
OFF CH1 OFF NULL MUTE
OFF NULL OFF
NULL OFF PRE 1
OFF NULL
NULL POST
NULL
MAIN
NULL
FX
EQ LOW L.MID HIGH
P/S peak n/a peak
H/L n/a low n/a
FREQ 130 Hz 96 Hz 5 kHz
GAIN 0 dB 0 dB 0 dB
To recall a Scene, press the Scene button and use the
Value encoder to scroll through the Scene library.
When you have found the Scene you wish to recall,
press the Recall button. By default, the StudioLive will
recall all stored parameters (Fat Channel settings,
channel muting and soloing, Aux mixes, and internal
effects parameters) except fader, knob, and graphic
EQ positions.
If you do not wish to recall a certain set of parameters,
simply set its Recalling group to "No" by using
the Next and Prev buttons to navigate through
the screen. When the Recalling group that you
wish to disable is selected, turn the Value Encoder
counter-clockwise to move it to the No (off )
position. Once you have disabled the parameters
you do not wish to recall, press the Recall button.
Owner's Manual
The StudioLive's recallable parameters are grouped as follows:
Mute: All channel and bus mutes (Channels 1-15/16, Aux 1-4)
FX: All parameters for the internal effects assigned to FXA and FXB
Assigns: All output and bus routing (Stereo Linking, FireWire returns to
inputs, Solo and Monitor bus assignments, FXA and FXB assignments,
and Master Control (Monitor, Solo Bus, and Talkback) assignments)
EQ and Dyn: Fat Channel panning, phase, dynamics processing
(Noise Gate, Compressor, EQ, and Limiter), and High-Pass
Filter parameters for every channel and bus
Aux Mix: All aux mixes (analog Aux Mixes 1-4, FXA and FXB, and Pre1/Pre2 positions)
Faders: All fader positions
Pots: All digital knob positions (FXA and FXB Levels, Solo
Bus Output, Phones, and Monitor knobs)
GEQ: Graphic EQ settings
If you enable fader positions as a part of a Scene recall, when you press the Recall
button, the StudioLive will automatically put the meters in Fader Locate mode. The
Fader Locate button will illuminate, and the meter section of the Fat Channel will
display the recalled fader position. To recall the stored position, move the faders up
or down until only the center LED is illuminated in each meter. To recall the Aux and
Main bus faders, simply move one of them. The Fat Channel meters will display the
recalled positions using the same meters on which each output is monitored.
As long as you remain in Fader Locate mode, the faders on your StudioLive will
not be active. The level of the audio passing through them will be set according
to the stored fader position, not the current location of the physical fader.
Once you have recalled each of the faders to their Scene location, press the
Locate button again. This will take you out of Fader Locate mode and reactivate
your faders so that they control the level of their channels and buses.
If you enable knob positions as a part of your Scene recall, all of the digital
knobs (FXA and FXB levels, Solo-bus output, Phones, and Monitor) will remain
at their stored position until they are moved manually. Once a knob is turned,
its value will jump to the value of its current physical position. Therefore, if
you intend to save a Scene and recall it later with knob-position recalling
enabled, it is highly recommended that you use the recall sheet provided
in the back of this manual to note the stored position of these controls.
It is important to note that the recalling groups have no effect on what
parameters are stored with a Scene. All storable parameters are saved
with a Scene regardless of what recalling groups are enabled.
Scenes, Presets, System Menu, and MIDI Control 5
Creating and Recalling a Scene 5.1
41 41