Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn Mower Accessories
  5. ULTRAVAC 126-6122
  6. Setup instructions

Exmark ULTRAVAC 126-6122 Setup Instructions

Hide thumbs Also See for ULTRAVAC 126-6122:

Advertisement

Quick Links

Download this manual
This product contains a chemical or chemicals known to the State of California to
Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part No.
—
Literature Pack
Manual-Operator's
© 2017—Exmark Mfg. Co., Inc.
P.O. Box 808
Beatrice, NE 68310
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
ULTRAVAC
Setup Instructions
For UltraVac Serial Nos. 400,000,000 & Higher
(To fit Radius Models Serial Nos. 400,000,000 & Higher)
Qty.
Fill out the online warranty registration
form.
All Rights Reserved *4503-418* C
Part No. 4503-418 Rev. C
Printed in the USA.
BAGGER
®
126-6122
Use

Advertisement

loading

Related Manuals for Exmark ULTRAVAC 126-6122

Summary of Contents for Exmark ULTRAVAC 126-6122

  • Page 1 Part No. Description Qty. Fill out the online warranty registration — form. Literature Pack Manual-Operator's © 2017—Exmark Mfg. Co., Inc. All Rights Reserved *4503-418* C Part No. 4503-418 Rev. C P.O. Box 808 Printed in the USA. Beatrice, NE 68310...
  • Page 2 Models and Required Completing Kits Completing Kits Note: Use the following charts to verify the kits required for the unit you are installing the UltraVac on. E- and S-Series Deck Completing Kit 126-6196 48 inch 52 inch 126-6197 60 inch 126-6198 X-Series Deck...
  • Page 3 Installing the Hopper Mount Brackets 1. Raise the deck to the transport position. Raise the back of the machine up and support the machine with jack stands. CAUTION Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous.
  • Page 4 g185955 Figure 5 g189991 1. Weight 4. Tabbed weight bracket Figure 4 plate 2. Mount channel 5. 3/8-16 x 2 1/2 inch square 1. Upper rear mount bracket 4. Hitch cover head bolt 2. 5/16-18 x 3 1/4 inch 5. Upper support bracket (if 3.
  • Page 5 g037183 Figure 7 1. Bolt 3. Washer 2. Knob 4. Caster weight g037341 Figure 8 48 and 52 Inch Decks 3. Insert the bolt through the bracket hole and install the washer and knob. 1. 3/8-16 x 1 1/4 inch carriage bolt 4.

  • Page 6: Installing The Blower Assembly

    3. Remove the right sheave nut and sheave from the spindle shaft. 4. Install the double sheave onto the right spindle shaft. • X-Series: Reinstall the spring disc washer and nut; torque to 130-160 ft-lb (176–217 N-m). g190023 Figure 11 g007021 1.
  • Page 7 3. Pull the spring loaded idler back and slip the belt over the top deck sheave. The belt should be routed as shown in Figure 13. g038066 Figure 15 g190065 1. Blower 3. Deck lip Figure 13 2. Belt cover View from Top of Blower 7.

  • Page 8: Installing The Hopper

    2. Press the tabs on the air vent into the notches on the inside of the hopper and secure with hairpins. g211079 Figure 16 1. LH hopper mount bracket g188636 Figure 18 2. Hopper frame 1. Air vent 3. Hairpin 3.
  • Page 9 2. Insert the upper tube into the hopper seal – push in then pull out so that the seal is extended outward. 3. Align the dimple on the upper tube with the end of hopper seal and orient between the two screws as shown in Figure 20.
  • Page 10 Installing the Bags 1. Raise the hood and install the bag assemblies onto the receivers of the hopper frame. 2. In order for the hood to seal properly against the bags when latched, check if the rear of the bag is 1/2–1 1/2 inches (12.7–38.1 mm) higher than the front (see Figure 23).
  • Page 11 g038069 Figure 24 1. Drill 3. #10-24 x 3/4 inch hex screw 2. #10 washer 4. ROPS pin with lanyard 2. Place the #10 washer and lanyard cable end onto the #10-24 x 3/4 inch hex screw and install into the RH ROPS hole.